User manual

25
This guarantees that the Illuminator cannot remain in opera-
on unintenonally. The LED glass bre displays the operang
condion of the dimmer and baery. When the LED is green,
the baery capacity is sucient for operaon. When the LED
is red, the baery capacity is almost exhausted and the bat-
tery should be replaced or charged. The dimmer switches o
automacally when the baery capacity is too low, thus pro-
tecng your baery from being run down too far.
Congratulations! You have bought a LASERLUCHS® laser dimmer! The laser dimmer has been
specially developed for LASERLUCHS® IR laser Illuminators and makes possible innite adjustment
of the output brightness.
The LASERLUCHS® laser dimmer is compatible with all LASERLUCHS® IR laser Illuminators and
provides you with a large number of innovative functions such as single-handed operation, battery
voltage monitoring and a microprocessor-controlled pulse shift mode, which provides excellent
results when it is misty, raining or snowing. In addition, it is possible to use the Illuminator to emit
the international SOS signal in the event of an emergency so as to attract the attention of rescuers
using night vision scopes.
1. Purpose:
The dimmer is intended for use with LASERLUCHS® laser
Illuminators and controls the intensity of the IR laser.
Warning: Do not operate the dimmer in areas where the-
re is a risk of explosions. Do not operate the dimmer un-
der water. If water penetrates the housing, it may lead to
malfunctions or permanent damage. Have the dimmer re-
paired only by an authorized specialist workshop or by the
LASERLUCHS® customer service. Do not make any modi-
cations to the dimmer. Serious risks may result from incor-
rect operation or use as well as from modications made
to the dimmer. The sole power source must be batteries of
the type CR123A or lithium ion batteries of the type CR123.
Note: Remove the battery if you are not using the laser
dimmer over a longer period of time. Do not short-circuit
or swallow the battery. Do not throw it onto a re.
2. Figure
3. Description/operation
The LASERLUCHS® dimmer makes possible innite adjustment
of the output brightness from 0 – 100%. This means that the
intensity of illumination can be adapted to the user’s require-
ments: for example, so as to respond to different ambient le-
vels of brightness and to improve the contrast of the night vi-
sion scope. The dimmer has been designed in such a way that
it can be operated comfortably in one hand. An intelligent con-
trol system prevents the battery from discharging in the event
of its being operated unintentionally, e.g. during transportati-
on. The use of glass bre optics and two-tone LED as a visual
display provides information on the operating condition
of the IR laser Illuminator and prevents unintentional
illumination of the user.
4. Preparation of the IR laser Illuminator
1) Unscrew the switch of the laser Illuminator and remove
the battery and spacer tube. The spacer tube is fastened with
silicone, but it may be released by being pulled out using one
nger. Any silicone residues must be completely removed
before screwing down.
2) Place the battery into the dimmer, by rst inserting the
battery with the minus pole toward the spring.
3) Screw down into the Illuminator until there is closure with
the rubber seal.
LED glass bre display
Operating button
–
+
3V
CR123A
+
–
Press
Turn
Congratulations! You have bought a LASERLUCHS® laser dimmer! The laser dimmer has been
specially developed for LASERLUCHS® IR laser Illuminators and makes possible innite adjustment
of the output brightness.
The LASERLUCHS® laser dimmer is compatible with all LASERLUCHS® IR laser Illuminators and
provides you with a large number of innovative functions such as single-handed operation, battery
voltage monitoring and a microprocessor-controlled pulse shift mode, which provides excellent
results when it is misty, raining or snowing. In addition, it is possible to use the Illuminator to emit
the international SOS signal in the event of an emergency so as to attract the attention of rescuers
using night vision scopes.
1. Purpose:
The dimmer is intended for use with LASERLUCHS® laser
Illuminators and controls the intensity of the IR laser.
Warning: Do not operate the dimmer in areas where the-
re is a risk of explosions. Do not operate the dimmer un-
der water. If water penetrates the housing, it may lead to
malfunctions or permanent damage. Have the dimmer re-
paired only by an authorized specialist workshop or by the
LASERLUCHS® customer service. Do not make any modi-
cations to the dimmer. Serious risks may result from incor-
rect operation or use as well as from modications made
to the dimmer. The sole power source must be batteries of
the type CR123A or lithium ion batteries of the type CR123.
Note: Remove the battery if you are not using the laser
dimmer over a longer period of time. Do not short-circuit
or swallow the battery. Do not throw it onto a re.
2. Figure
3. Description/operation
The LASERLUCHS® dimmer makes possible innite adjustment
of the output brightness from 0 – 100%. This means that the
intensity of illumination can be adapted to the user’s require-
ments: for example, so as to respond to different ambient le-
vels of brightness and to improve the contrast of the night vi-
sion scope. The dimmer has been designed in such a way that
it can be operated comfortably in one hand. An intelligent con-
trol system prevents the battery from discharging in the event
of its being operated unintentionally, e.g. during transportati-
on. The use of glass bre optics and two-tone LED as a visual
display provides information on the operating condition
of the IR laser Illuminator and prevents unintentional
illumination of the user.
4. Preparation of the IR laser Illuminator
1) Unscrew the switch of the laser Illuminator and remove
the battery and spacer tube. The spacer tube is fastened with
silicone, but it may be released by being pulled out using one
nger. Any silicone residues must be completely removed
before screwing down.
2) Place the battery into the dimmer, by rst inserting the
battery with the minus pole toward the spring.
3) Screw down into the Illuminator until there is closure with
the rubber seal.
LED glass bre display
Operating button
–
+
3V
CR123A
+
–
Press
Turn
Congratulations! You have bought a LASERLUCHS® laser dimmer! The laser dimmer has been
specially developed for LASERLUCHS® IR laser Illuminators and makes possible innite adjustment
of the output brightness.
The LASERLUCHS® laser dimmer is compatible with all LASERLUCHS® IR laser Illuminators and
provides you with a large number of innovative functions such as single-handed operation, battery
voltage monitoring and a microprocessor-controlled pulse shift mode, which provides excellent
results when it is misty, raining or snowing. In addition, it is possible to use the Illuminator to emit
the international SOS signal in the event of an emergency so as to attract the attention of rescuers
using night vision scopes.
1. Purpose:
The dimmer is intended for use with LASERLUCHS® laser
Illuminators and controls the intensity of the IR laser.
Warning: Do not operate the dimmer in areas where the-
re is a risk of explosions. Do not operate the dimmer un-
der water. If water penetrates the housing, it may lead to
malfunctions or permanent damage. Have the dimmer re-
paired only by an authorized specialist workshop or by the
LASERLUCHS® customer service. Do not make any modi-
cations to the dimmer. Serious risks may result from incor-
rect operation or use as well as from modications made
to the dimmer. The sole power source must be batteries of
the type CR123A or lithium ion batteries of the type CR123.
Note: Remove the battery if you are not using the laser
dimmer over a longer period of time. Do not short-circuit
or swallow the battery. Do not throw it onto a re.
2. Figure
3. Description/operation
The LASERLUCHS® dimmer makes possible innite adjustment
of the output brightness from 0 – 100%. This means that the
intensity of illumination can be adapted to the user’s require-
ments: for example, so as to respond to different ambient le-
vels of brightness and to improve the contrast of the night vi-
sion scope. The dimmer has been designed in such a way that
it can be operated comfortably in one hand. An intelligent con-
trol system prevents the battery from discharging in the event
of its being operated unintentionally, e.g. during transportati-
on. The use of glass bre optics and two-tone LED as a visual
display provides information on the operating condition
of the IR laser Illuminator and prevents unintentional
illumination of the user.
4. Preparation of the IR laser Illuminator
1) Unscrew the switch of the laser Illuminator and remove
the battery and spacer tube. The spacer tube is fastened with
silicone, but it may be released by being pulled out using one
nger. Any silicone residues must be completely removed
before screwing down.
2) Place the battery into the dimmer, by rst inserting the
battery with the minus pole toward the spring.
3) Screw down into the Illuminator until there is closure with
the rubber seal.
LED glass bre display
Operating button
–
+
3V
CR123A
+
–
Press
Turn
Congratulations! You have bought a LASERLUCHS® laser dimmer! The laser dimmer has been
specially developed for LASERLUCHS® IR laser Illuminators and makes possible innite adjustment
of the output brightness.
The LASERLUCHS® laser dimmer is compatible with all LASERLUCHS® IR laser Illuminators and
provides you with a large number of innovative functions such as single-handed operation, battery
voltage monitoring and a microprocessor-controlled pulse shift mode, which provides excellent
results when it is misty, raining or snowing. In addition, it is possible to use the Illuminator to emit
the international SOS signal in the event of an emergency so as to attract the attention of rescuers
using night vision scopes.
1. Purpose:
The dimmer is intended for use with LASERLUCHS® laser
Illuminators and controls the intensity of the IR laser.
Warning: Do not operate the dimmer in areas where the-
re is a risk of explosions. Do not operate the dimmer un-
der water. If water penetrates the housing, it may lead to
malfunctions or permanent damage. Have the dimmer re-
paired only by an authorized specialist workshop or by the
LASERLUCHS® customer service. Do not make any modi-
cations to the dimmer. Serious risks may result from incor-
rect operation or use as well as from modications made
to the dimmer. The sole power source must be batteries of
the type CR123A or lithium ion batteries of the type CR123.
Note: Remove the battery if you are not using the laser
dimmer over a longer period of time. Do not short-circuit
or swallow the battery. Do not throw it onto a re.
2. Figure
3. Description/operation
The LASERLUCHS® dimmer makes possible innite adjustment
of the output brightness from 0 – 100%. This means that the
intensity of illumination can be adapted to the user’s require-
ments: for example, so as to respond to different ambient le-
vels of brightness and to improve the contrast of the night vi-
sion scope. The dimmer has been designed in such a way that
it can be operated comfortably in one hand. An intelligent con-
trol system prevents the battery from discharging in the event
of its being operated unintentionally, e.g. during transportati-
on. The use of glass bre optics and two-tone LED as a visual
display provides information on the operating condition
of the IR laser Illuminator and prevents unintentional
illumination of the user.
4. Preparation of the IR laser Illuminator
1) Unscrew the switch of the laser Illuminator and remove
the battery and spacer tube. The spacer tube is fastened with
silicone, but it may be released by being pulled out using one
nger. Any silicone residues must be completely removed
before screwing down.
2) Place the battery into the dimmer, by rst inserting the
battery with the minus pole toward the spring.
3) Screw down into the Illuminator until there is closure with
the rubber seal.
LED glass bre display
Operating button
–
+
3V
CR123A
+
–
Press
Turn
4.2 Figure Dimmer
5. Performance test / trouble-shoong
So as to test the proper performance of the LED IR-Illu-
minator, you need a night vision scope or a CCD came-
ra (e.g. mobile telephone camera or a digital camera).
Do not direct the beam directly into the night vision scope
so as to avoid damaging the sensive image intensier tube.