Specification

ManualsBrandsLatex-ite ManualsKitchen4.75 Gal. Optimum Driveway FIller Sealer

Dalton Enterprises, Inc., 131 Willow Street, Cheshire, CT 06410

Phone 800-851-5606 • Fax (203) 271-3396 • www.latexite.com

Revised 09/28/16

TECHNICAL DATA SHEET

Latex•ite

OPTIMUM

DRIVEWAY SEALER

Manufacturer Product#: 10852

UPC#: 090932108523

Appearance:

Thick brown liquid. Dries black.

Maximum VOC:

Less than 25 g/L

Application Temperature:

55º F and rising.

Specific Gravity:

1.3-1.5

Viscosity:

5,000-10,000 cps

Weight Per Gallon:

10.8-11.6 lbs. per gallon

Color:

Brown in liquid state. Dries black.

Consistency:

Thick liquid.

Boiling Point:

>212º F

Cure Time (50% relative humidity, 70º F):

24-48 hours.

Freeze ability:

Do not allow to freeze.

Container Size & Weight:

4.75gallons, Approximately 55 lbs.

Latex·ite

Optimum

Driveway Filler Sealer is an asphalt emulsion based sealer designed to beautify and protect. Optimum

will leave a deep black color while providing strength and flexibility with its advanced polymer system. Latexite

Optimum

an EZ-Stir formulation saving you time and making it easy to apply!

Features:



8 year warranty



Fiber reinforced for maximum strength



Premium no stir formula…save time and effort



Advanced polymer formula



Non skid formula



Apply with Seal Right Squeegee (Roller is wrong applicator and voids warranty)

*Note: Product dries black…is brown only in liquid form.

Coverage rates vary depending upon the condition of the existing blacktop. Smooth & previously sealed driveways will

average 400-500 square feet per pail. Rough & unsealed surfaces will average 300-400 sq. ft. per one 4.75 gallon pail. Rough

/ road-grade asphalts with larger aggregate can cause lower than normal coverage rates. Thin coats are recommended as thick

coats will result in uneven coverage, tracking, and curing problems. A second coat can be applied 24 hours after first

application.

Sweep and clean off entire driveway using Latex•ite

CLEANER/DEGREASER. Scrub oil, gas spots, stains and rinse with

water. Apply Latex•ite

OIL SPOT PRIMER to any oil spots/stains using a paint brush. Allow Latex•ite

OIL SPOT

PRIMER to dry ½ hour prior to sealing over. If pavement is extremely hot, apply a fine water mist prior to sealing, but avoid

PHYSICAL PROPERTIES & PERFORMANCE

FEATURES

COVERAGE

SURFACE PREPARATION

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA SHEET Latex•ite® OPTIMUM® DRIVEWAY SEALER Manufacturer Product#: 10852 UPC#: 090932108523 PHYSICAL PROPERTIES & PERFORMANCE Appearance: Thick brown liquid. Dries black. Application Temperature: 55º F and rising. Viscosity: 5,000-10,000 cps Color: Brown in liquid state. Dries black. Boiling Point: >212º F Freeze ability: Do not allow to freeze. Maximum VOC: Less than 25 g/L Specific Gravity: 1.3-1.5 Weight Per Gallon: 10.8-11.6 lbs. per gallon Consistency: Thick liquid.
PAGE 2
creating any standing water. Brush out any remaining puddles. You can edge the driveway with a large paint or wall paper brush by dipping brush into sealer and slowly edging the driveway (put a tarp over any concrete areas so you don’t accidentally get sealer onto concrete). Complete surface preparations and allow area to completely dry (24 hours recommended). Newly paved surfaces must cure for a minimum of 12 months. APPLICATION DO NOT DILUTE SEALER.
PAGE 3
!!!CAUTION!!! CAUTION! HARMFUL OR FATAL IF SWALLOWED! Latex•ite® OPTIMUM® is for exterior use only. Keep out of reach of children. Keep container capped when not in use. Nonflammable. This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. Emergency & First Aid Procedures: Eyes: Immediately flush with clean water for 15 minutes while holding eyelids open; consult a physician.