Specification

ManualsBrandsLatex-ite ManualsKitchen4.75-Gal. Color Grade Blacktop Driveway Filler/Sealer in Natural Beige

Dalton Enterprises, Inc., 131 Willow Street, Cheshire, CT 06410

Phone 800-851-5606 • Fax (203) 271-3396 • www.latexite.com

Revised 09/28/16

TECHNICAL DATA SHEET

Latex•ite

Color Grade

Manufacturer Product#: Red: 11300, Beige: 11310, Gray: 11320

UPC#: Red: 090932113008, Beige: 090932113107, Gray: 090932113206

PHYSICAL PROPERTIES & PERFORMANCE

FEATURES

Latex·ite

Color Grade

Driveway Filler/Sealer is a ready-to-use, high performance, water based blacktop driveway sealer (NOT

FOR CONCRETE) that will beautify and protect the entrance to your home. Customers have asked for a color sealant for their

blacktop walkways and driveways…so here it is! Color Grade

is a durable, tinted filler/sealer that resists hot tire pick-up, chemicals

and leaves a non-skid finish. It is available in three colors: Natural Beige, Dover Grey and Brick Red. The temperature of the blacktop

will certainly be reduced by using a lighter shade like the grey or beige. Our recent test on Beige showed an 18 degrees F reduction

versus the blacktop.

Features:

 Advance Polymer Formula

 Resists Hot Tire Pick Up

 Fortified, Non-Skid

 UV Protected

 Low VOC, Easy Clean-Up

 Apply with Seal Right Squeegee (Roller is wrong applicator and voids warranty)

 Not for use on stamped asphalt

COVERAGE

Coverage rates vary depending upon the condition of the existing blacktop. Smooth & previously sealed driveways will average

400-500 square feet per pail. Rough & unsealed surfaces will average 300-400 sq. ft. per one 4.75 gallon pail. Rough / road-

grade asphalts with larger aggregate can cause lower than normal coverage rates. Two thin coats are recommended as thick coats

Appearance:

Thick Colored Liquid.

Maximum VOC:

Less than 25 g/L

Application Temperature:

55º F and rising.

Specific Gravity:

1.3-1.5

Viscosity:

5,000-10,000 cps

Weight Per Gallon:

9.2-11.6 lbs. per gallon

Color:

Red, Beige, or Gray

Consistency:

Thick liquid.

Boiling Point: >212º

Cure Time (50% relative humidity, 70º F): 24-48

hours.

Freeze ability:

Do not allow to freeze.

Container Size & Weight:

4.75gallons, Approximately 52 lbs.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA SHEET Latex•ite® Color Grade® Manufacturer Product#: Red: 11300, Beige: 11310, Gray: 11320 UPC#: Red: 090932113008, Beige: 090932113107, Gray: 090932113206 PHYSICAL PROPERTIES & PERFORMANCE Appearance: Thick Colored Liquid. Application Temperature: 55º F and rising. Viscosity: 5,000-10,000 cps Color: Red, Beige, or Gray Boiling Point: >212º F Freeze ability: Do not allow to freeze. Maximum VOC: Less than 25 g/L Specific Gravity: 1.3-1.5 Weight Per Gallon: 9.2-11.6 lbs.
PAGE 2
will result in uneven coverage, tracking, and curing problems. If needed, a second coat can be applied 24 hours after the first application. SURFACE PREPARATION Sweep and clean off entire driveway using Latex•ite® CLEANER/DEGREASER. Scrub oil, gas spots, stains and rinse with water. Apply Latex•ite® OIL SPOT PRIMER to any oil spots/stains using a paint brush. Allow Latex•ite® OIL SPOT PRIMER to dry ½ hour prior to sealing over.
PAGE 3
Avoid applying sealer when temperatures drop below 55º F. Allow all repaired surfaces to cure 24 hours prior to sealing. For crack fillers you should wait 24 hours. If the crack filler is firm you may seal over. When transporting this product, ensure that the container is secured and the lid is secure. Do not allow the container to tumble as this may loosen the lid and allow leakage to occur. Do not transport on passenger seats or inside the passenger compartment of any vehicle.