Instructions / Assembly

ManualsBrandsLatex-ite ManualsKitchen4.75-Gal. Ultra Shield Driveway Filler Sealer

Español a termino del documento

All Latex

●

ite

asphalt driveway sealers are time-tested and performance proven. Professional grade

formulas that are user friendly for the Do-It-Yourselfer. Latex

●

ite

driveway sealing products go on easier /

faster, perform better and look the BEST! So use Latex

●

ite

asphalt driveway sealers and do it right the first

time. When you Do It Yourself you are ensured of a high quality product from Dalton, The Leaders in

Driveway Maintenance…since 1945

Once the asphalt is repaired and cleaned (and any gas or oil spot have been primed) ... you are ready to seal.

DON'T SEAL OVER PROBLEMS! Apply only if weather is clear and dry. DO NOT APPLY when rain or fog is

imminent or likely within 48 hours. Also, do not apply very late in the day. For best results both surface and air

temperature should be above 55°F and rising for proper adhesion. Early Spring or late Fall applications will most

likely result in the sealer not performing well.

Stir

Premix 1/2 of the pails you expect to use…you can even have an empty 5gal pail there

And mix them all back and forth – this is called ‘boxing or batching’.

Summary of content (7 pages)

PAGE 1
Español a termino del documento All Latex●ite® asphalt driveway sealers are time-tested and performance proven. Professional grade formulas that are user friendly for the Do-It-Yourselfer. Latex●ite® driveway sealing products go on easier / faster, perform better and look the BEST! So use Latex●ite® asphalt driveway sealers and do it right the first time. When you Do It Yourself you are ensured of a high quality product from Dalton, The Leaders in Driveway Maintenance…since 1945®.
PAGE 2
Mix additional pails as needed. If you have had the pails for a while you may want to (while still closed!) flip them over the night prior to sealing as it will be much easier to mix the next morning. Mist (Only when the pavement is very HOT) Start at the end of the driveway farthest from the street (start approximately 2 feet out). Apply a fine mist of water to the pavement to lightly dampen the pavement ... leave no standing puddles of water. Apply sealer to the dampened pavement. Re-mist as needed.
PAGE 3
Seal Once you've poured a bead across the driveway, use your squeegee to pull the sealer back and forth, in a moon shape, across the driveway starting near your house and working down towards the street. (Maintain a wet bead or edge to avoid streak marks.) See photos below. Remember to drag squeegee back and forth ... do not push. Apply pressure to leave a thin coat. Two thin coats are better than one thick coat.
PAGE 4
Curing Block off the driveway with the empty pails and stay off the driveway for a minimum of 24-48 hours. The sealer may take longer to cure if it is humid. On a nice day if you are applying a 2nd coat you should be able to apply 2 hours after first coat has been applied (if there are shaded areas allow more time). Clean Up Latex ite® water-based formulas make clean up quick and easy. Simply clean tools and empty buckets with plain water immediately after use.
PAGE 5
En Espanol 1. Limpiar… Barrer y limpiar toda la entrada Eliminar manchas de aceite y combustible - enjuagar los restos con agua. 2. Sellar… Evitar que las manchas de aceite penetren aplicando un sellador fuerte. Va con blanco… se seca transparente. El sellador para manchas de aceite se vende en latexite.com 3. Rellenar… Recortar el pico y verter el relleno en la grieta justo por debajo del borde asfáltico No rellenar demasiado. Permanece maleable. 4.
PAGE 6
. Sellar… para lograr MEJORES resultados… dejar curar el parche y las reparaciones un mínimo de 24 horas. Aplicar el sellador sólo si hay 55ºF o más y si no hay pronóstico de lluvia para las próximas 24 horas www.latexite.
PAGE 7