ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS: .A. 1.Remove hardware from box and sort by size. 2.Please check to see that all hardware and parts are present prior to start of assembly. 3.Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly. Warning! 1.Don't attempt to repair or modify parts that are broken or defective.Please contact the store immediately. 2.This product is for home use only and not intended for commercial establishment.
(S) UPPER BOTTOM PANEL (T) UPPER CROSS PANEL (U) UPPER TOP PANEL (V) UPPER BACK PANEL (W)MIRROR z NO ' ' <> <> 1PC 2PCS (X) SEAT SIDE PANEL (Y) SEAT BOTTOM PANEL <> <> 2PCS 1PC 1PC (AA) SEAT FRONT DIVIDER PANEL <:> 1PC 1PC (AB) SEAT BACK DIVIDER PANEL <:> 1PC 1PC (AC) SEAT CUSHION 1PC HARDWARE PACKAGE DESCRIPTION GLUE40g DESCRIPTION FIGURE QTY NO V 1PC 8 HANDLE L=120mm 35PCS 9 HANDLE BOLT 4i4x20mm 2PCS 1SET , FIGURE � QTY 1PC 2 WOODEN DOWEL 4i8x30mm 3 CAM BOLT 4
z HARDWARE PACKAGE NO DESCRIPTION FIGURE QTY NO DESCRIPTION 15 HINGE SCREW \1>4x15mm 14PCS 20 FIXER 16 PIPE THREAD \1>6.2x45mm 2PCS 21 FIXER SCREW \I> 3x19mm 17 LARGE BOLT \1>4.5x20mm 2PCS 22 RING BOX 18 METAL PLATE 4.5x12.3x1.2mm 2PCS 23 STICKER \I> 20mm 19 METAL PLATE SCREW \I> 3x15mm � � FIGURE QTY @ BPCS BPCS � 1PC 5PCS � 4PCS STEP 1 ,/tjp-�, 11 ( 2 \ (3)x10) / 2 @ 6 ' \ \___ ;____? ,-�', \Jl- � ' .______ _ _..
STEP2 /! I I / ,i , ® STEP3 The Glue (1) should be used in the indicated locations to help solidify the assembled unit. \ , page 5 of 13 \ -�
STEP4 The Glue (1) should be used in the indicated locations to help solidify the assembled unit. 2 2 ,--� INCORRECT CORRECT \ ( \ (7)x10 /' --.
STEP6 The Glue (1) should be used in the indicated locations to help solidify the assembled unit.
STEPS STEP9 • / / / / // (1/i ---- � ---- I � '\ (16)x2 (17)X2 \¼ / � ' - _,,/ page 8 of 13 / L--r --- 17
STEP10 Detail #2 ';J 20 \,_ - 0 /- " 'V ( (20) §�w:w.-11� \-21\)x '------ /' ' , 20 - <20 20, j I/ 18 20 ti 20 20, ., " I/ STEP11 The Glue (1) should be used in the indicated locations to help solidify the assembled unit.
STEP12 The Glue (1) should be used in the indicated locations to help solidify the assembled unit. . \ � � STEP13 page 10 of 13
STEP14 The Glue (1) should be used in the indicated locations to help solidify the assembled unit.
STEP15 / / / / / STEP16 / / / / / / / =-=-=-= �- -'=-.
Assembly Instruction as below: Step 1: Insert (2) into the holes at two sides of (C)/(D) , Insert (2) into the holes at top side of (A)/(8) , Insert (3) into the holes on the (A)/(8)/(E) , Nail (6) at bottom of (A)/(8) , then (10-CL) on (A) , (10-CR) on (B) by (11). Step 2: Connect (C)/(D) with (A) , when (3) is connected inside (4) , tightly fasten (4) clockwise. Insert (G) on and between (C)&(D) along slots. Apply the same technique to connect (C)/(D) with (8).
