Instructions / Assembly

DEFECT
CAUSE
REMEDY
1. The burner does not
turn on is has difficulty
turning on or turns off.
1. Gas is not reaching the burner.
Check that the cylinder and grill cocks are open, and that there is gas in the
cylinder. Check all of the gas lines.
2. The rubber hose, cock, Venturi tube or burner orifices
are clogged.
Disassemble the Venturi tube with the burner and remove the obstruction (e.g. a
spider nest or web), then clean the injector hole with a needle. With the air gun
connected to a compressor, blow inside the gas connection with the gas cocks
open in the maximum position.
3. The pressure reducer does not work.
Replace the pressure regulator with one to standard.
4. The Venturi tube does not wrap around the injector.
Disassemble the burner and reassemble it properly.
2. Flame very weak,
unsteady, yellow or of
different shape on the
burner’s surface.
1. Injector or Venturi tub clogged by a spider nest or web.
Disassemble the Venturi tube with the burner and remove the spider nest or web,
then clean the injector hole with a needle. With the air gun connected to a
compressor, blow inside the gas connection with the gas cocks open in the
maximum position.
2. Maybe the gas in the cylinder has run out or the gas
also contains a large amount of air.
Install a new cylinder.
3. The injector holder is not positioned correctly on the
Venturi tube.
Disassemble the burner and reassemble it properly.
4. If an adjustable pressure regulator is used, it may be
at minimum or may be broken.
Try to replace the pressure regulator.
3. Flames in the injector.
The cylinder is almost empty.
Replace the cylinder.
4. Gas leaks from a cock
on the knob side.
1. The pressure regular was not used.
First install or replace the pressure regulator with one to standard and then
completely replace the gas ramp.
2. Pressure regulator broken.
3. The pressure regulator is the adjustable type, not to
standard.
4. Faulty cock.
Completely replace the gas ramp.
5. Gas leaks from the end
of the Venturi tube on
the cock side.
1. There is a spider nest or web inside the Venturi tube or
burner.
Disassemble the Venturi tube with the burner and remove the spider nest or web.
2. Too large a gap between the Venturi tube and the
cock casting.
Close the Venturi tube with pliers so as to reduce the gap.
6. Large blaze that puts
everything on fire.
Accumulation of unburned gas on the bottom of the
tray because the cock remained wide open before the
spark went off.
Replace any damaged pieces and never repeat the incorrect operation again.
7. The lava rock flares up
a lot.
1. Too fatty food.
Wait for the fat to come out of the food, and then wash the lava rocks with boiling
water. If the problem persists, replace them with new ones.
2. Too much fat on the lava stones.
Wash them with boiling water and if the problem persists, replace them with new
ones.
3. The grease drainage system is clogged.
Clean it.
4. Grill temperature too high.
Reduce delivery.
8. The burner turns on
with a match but not
with the on push-
button.
1. The glow plug has shifted.
Adjust the tip of the glow plug in front of a burner hole.
2. Faulty push-button, wire or electrode.
Check the conditions of the ceramic components and those of the connection
cable and ignition device.
9. The knob does not turn.
1. The knob is too close to the body and gets stuck on
the fixing screw of the cock.
Move the knob slightly away from the body.
2. The knob still does not turn, even if it is at a distance.
The gas cock may have sustained damage. In this case, completely replace the
gas ramp.
DIFETTO
CAUSA
RIMEDIO
1. Il bruciatore non si
accende o ha difficoltà
di accendersi o si
spegne.
1. Non arriva il gas al bruciatore.
Controllare che il rubinetto della bombola e della bistecchiera siano aperti e che
ci sia gas nella bombola. Verificare tutti i condotti del gas.
2. Il tubo in gomma, o il rubinetto, o il tubo venturi o gli
orifizi del bruciatore sono otturati.
Smontare il tubo venturi con il bruciatore e rimuovere l’ostruzione (per esempio
un nido di ragno o ragnatela), poi con uno spillo pulire il foro dell’iniettore. Con la
pistola dell’aria collegata ad un compressore, soffiare dentro all’attacco gas con i
rubinetti del gas aperti nella posizione del massimo.
3. Il riduttore di pressione non funziona.
Sostituire il regolatore di pressione con uno a norma.
4. Il tubo venturi non avvolge l’iniettore.
Smontare il bruciatore e rimontarlo correttamente.
2. Fiamma molto debole o
instabile o gialla o di
forma diversa sulla
superficie del
bruciatore.
1. Iniettore o tubo venturi otturati dalla presenza di nido
di ragno o ragnatela.
Smontare il tubo venturi con il bruciatore e rimuovere il nido di ragno o ragnatela
poi con uno spillo pulire il foro dell’iniettore. Con la pistola dell’aria collegata ad
un compressore, soffiare dentro all’attacco gas con i rubinetti del gas aperti nella
posizione del massimo.
2. Forse il gas nella bombola è finito oppure il gas
contiene anche molta aria.
Prendere una bombola nuova.
3. Il porta iniettore è mal posizionato nel tubo venturi.
Smontare il bruciatore e rimontarlo correttamente.
4. Se è utilizzato un regolatore di pressione regolabile,
questo può essere al minimo oppure rotto.
Provare a cambiare il regolatore di pressione.
3. Fiamme nell’iniettore.
La bombola è quasi vuota.
Cambiare la bombola.
4. Fuoriuscita di gas da un
rubinetto dal lato della
manopola.
1. Non è stato usato il regolatore di pressione.
Prima mettere o sostituire il regolatore di pressione con uno a norma e poi
sostituire integralmente la rampa gas.
2. Rottura del regolatore di pressione.
3. Il regolatore di pressione è del tipo regolabile non a
norma.
4. Rubinetto difettoso.
Sostituire integralmente la rampa gas.
5. Fuoriuscita gas
dall’estremità del tubo
venturi dal lato del
rubinetto.
1. Presenza di nido di ragno o ragnatela all’interno del
tubo venturi o del bruciatore.
Smontare il tubo venturi con il bruciatore e rimuovere il nido di ragno o ragnatela.
2. Eccessivo gioco tra tubo venturi e il getto del rubinetto.
Chiudere con una pinza il tubo venturi in modo da ridurre il gioco.
6. Gran fiammata che
incendia tutto
Accumulo di gas non bruciato sul fondo della bacinella
perché il rubinetto è rimasto molto aperto prima di fare
scoccare la scintilla.
Sostituire eventuali pezzi danneggiati e non ripetere più l’operazione sbagliata.
7. La roccia lavica si
infiamma molto.
1. Cibo troppo grasso.
Attendere che esca il grasso dal cibo e poi lavare le rocce laviche con acqua
bollente. Se il problema continua sostituirle con delle nuove.
2. Troppo grasso sulle pietre laviche.
Lavarle con acqua bollente e se il problema continua sostituirle con delle nuove.
3. Il sistema di scolo del grasso è otturato.
Pulirlo.
4. Temperatura del grill troppo elevata.
Ridurre la portata.
8. Il bruciatore si accende
con un fiammifero ma
non con il pulsante di
accensione.
1. La candeletta si è spostata.
Regolare la punta della candelette davanti ad un foro del bruciatore.
2. Pulsante, filo o elettrodo difettoso.
Controllare le condizioni degli elementi in ceramica e quelli del cavo di
collegamento e del dispositivo di accensione.
9. La manopola non gira.
1. La manopola è troppo vicina alla scocca e si blocca
sulla vite di fissaggio del rubinetto.
Allontanare leggermente la manopola dalla scocca.
2. La manopola anche se è lontana dalla scocca non
gira.
Il rubinetto del gas può avere subito dei danni. In questo caso, sostituire
integralmente la rampa gas.