Version: V1.00.001 Revised date: 03-18-2019 Statement: LAUNCH owns the complete intellectual property rights for the software used by this product. For any reverse engineering or cracking actions against the software, LAUNCH will block the use of this product and reserve the right to pursue their legal liabilities.
LAUNCH X-431 V+ User Manual — Safety Precautions Copyright Information Copyright © 2019 by LAUNCH TECH. CO., LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of LAUNCH. The information contained herein is designed only for the use of this unit.
LAUNCH X-431 V+ User Manual — Safety Precautions Important Safety Precautions Important: To avoid personal injury, property damage, or accidental damage to the product, read all of the information in this section before using the product. Never collide, throw, or puncture X-431 V+, and avoid falling, extruding and bending it. Do not insert foreign objects into or place heavy objects on your device. Sensitive components inside might cause damage.
LAUNCH X-431 V+ User Manual — Safety Precautions various poisonous compounds (hydrocarbon, carbon monoxide, nitrogen oxides, etc.) Do not connect or disconnect any test equipment while the ignition is on or the engine is running. Put blocks in front of the drive wheels and never leave the vehicle unattended while testing. Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clear the outside of the equipment as necessary.
LAUNCH X-431 V+ User Manual — Table of Contents TABLE OF CONTENTS 1 INTRODUCTION ............................................................................................ 1 1.1 PRODUCT PROFILE .................................................................................... 1 1.2 FEATURES ................................................................................................ 3 1.3 KNOWLEDGE OF X-431 V+ ........................................................................ 4 1.3.
LAUNCH X-431 V+ User Manual — Table of Contents 4.1 DIAGNOSIS FLOWCHART .......................................................................... 19 4.2 USER REGISTRATION, CONNECTOR ACTIVATION & DIAGNOSTIC SOFTWARE DOWNLOAD .................................................................................................. 19 4.2.1 User registration ............................................................................. 19 4.2.2 Diagnostic software layout .............................................
LAUNCH X-431 V+ User Manual — Table of Contents 4.8.6 Profile ............................................................................................. 44 4.8.7 Change password .......................................................................... 44 4.8.8 Help ............................................................................................... 44 4.8.9 Log out ........................................................................................... 44 4.9 SETTINGS ...................
LAUNCH X-431 V+ User Manual — General Operations 1 Introduction 1.1 Product Profile X-431 V+ is a new Android-based vehicle trouble diagnostic tool. It is characterized by featuring powerful functions, and providing precise test result. Through simple wireless communication between VCI and X-431 V+ tablet, it achieves full car model and full system vehicle trouble diagnosis, which include Reading DTCs, Clearing DTCs, Reading Data Stream, Actuation Test and Special Functions.
LAUNCH 2. X-431 V+ User Manual — General Operations Commercial Vehicle version X-431 V+ is compatible with the following two Heavy-duty VCI modules. For different VCI modules, the communication methods vary. Below shows how the X-431 V+ system works. A. HD-II module: B. HD-III module: Besides the BT communication, the HD-III VCI module comes loaded with a built-in WLAN module, which can work as a wireless hotspot or a network adaptor. Below shows how the X-431 V+ system works.
LAUNCH X-431 V+ User Manual — General Operations 1.2 Features 1. Diagnose: Diagnose the electronic control system of prevailing vehicle models covering Asian, European, American and Chinese. Diagnosis functions include: Read DTCs, Clear DTCs, Read Data Stream, Special Functions etc. Specially designed for Android platform with user-friendly interface. It is simple for the VCI (Vehicle Communication Interface) to communicate with X-431 V+.
LAUNCH X-431 V+ User Manual — General Operations revenue: Electronic throttle position reset/learn and gear learning etc. 2. Repair Data: Provides a mass of service information for various vehicle models, which enables users to retrieve service data of some vehicle online. 3. Update: Lets you update your diagnostic software more efficiently. 4. Browser: Built-in Wi-Fi module makes surfing on the internet freely. 5. Email: Allows you to send and receive emails. 6.
LAUNCH X-431 V+ User Manual — General Operations In Off mode, press it for 3 seconds to turn the tablet on. In On mode: 1 POWER Key Press it to activate the LCD if the LCD is off. Press it to turn off the LCD if the LCD lights up. Press it for 3 seconds to turn it off. Press it for 8 seconds to perform forced shutdown. 2 VOLUME +/- Key 3 LCD Screen 4 Microphone 5 Data transmission/Charging Port 6 Rear Camera 7 Speakers To adjust the volume. To connect to AC outlet for charging.
LAUNCH X-431 V+ User Manual — General Operations 1.3.2 VCI connector (Only for Passenger Vehicle Version) The VCI connector works as a vehicle communication interface device, which is used to connect to the vehicle’s DLC (Data Link Connector) socket directly or via OBD II extension cable to read the vehicle data and then send it to the X-431 V+ tablet via wireless BT communication. Fig. 1-2 VCI connector 1 OBD-16 diagnostic connector To connect on vehicle’s OBD II DLC.
LAUNCH 5 Data I/O port X-431 V+ User Manual — General Operations This port is temporarily disabled and reserved for subsequent function extension. 1.3.2 VCI module (Only for Commercial Vehicle Version) A. HD-II Module As the 2nd generation of heavy-duty module, it mainly functions as a VCI device for accessing vehicle data. Fig. 1-2 HD-II VCI module LED indicators: It is defined as follows(from left to right): Power Indicator: It lights up when it is powered on.
LAUNCH X-431 V+ User Manual — General Operations Communication LED of PC Data I/O LED 2 Data I/O port 3 Communication Port of PC 4 Diagnostic Socket: To connect the included diagnostic cable. 5 DC-IN power jack: To connect the power adaptor. B. HD-III Module As the 3rd generation of heavy-duty module, it works as a vehicle communication interface device, which is used to read the vehicle data and then send it to the X-431 V+ via wireless BT/WLAN communication.
X-431 V+ User Manual — General Operations LAUNCH 1 DC-IN power jack: For connecting the power adaptor. 2 Diagnostic socket: For connecting the diagnostic cable. LED indicators: It is defined as follows: Vehicle: While communicating with the vehicle, the indicator lights up and flashes. Otherwise, it will not illuminate. Power: It illuminates solid red when the module is powered on. 3 BT: Blue indicates the module is working in wireless BT mode.
LAUNCH Connectivity X-431 V+ User Manual — General Operations WLAN (802.11b/g/n) BT 4.0 Working temperature 0℃ ~ 45℃ Storage temperature -20℃ ~ 70℃ 1.4.2 VCI connector (Only for Passenger Vehicle Version) Working voltage DC 9 ~18V Average working current About 128mA Standby current About 50mA Working temperature -20 to 55℃ Storage temperature -30 to 70℃ Storage humidity <80% Working humidity <60% 1.4.2 VCI module (Only for Commercial Vehicle Version) A.
X-431 V+ User Manual — General Operations LAUNCH Communication Via wireless BT/WLAN or data cable Working temperature -10 to 55℃ WIFI module HLK-RM08K Frequency range: 2412-2472MHz Transmit power: 19.29dBm Wireless BT module YG-218M-A2 Frequency range: 2402-2480MHz Transmit power: 16.62dBm 1.5 Package List (For Passenger Vehicle Version) Common accessories for each X-431 V+ are same, but for different destinations, the accessories (such as diagnostic software, adaptor cables) may vary.
LAUNCH X-431 V+ User Manual — General Operations 7 Battery clamps cable To supply power to the non-16pin connector from the vehicle’s battery. 8 OBD I adaptor box For connecting the VCI connector and (Optional) non-16pin adaptor cable. 9 Non-16pin adaptor cable kit To connect to the vehicle equipped (Optional) with non-OBD II management system. 1 1.
LAUNCH X-431 V+ User Manual — General Operations 8 Power adaptor For charging the tablet via AC outlet. 1 9 Cigarette lighter cable To supply power to the non-16pin connector from the vehicle’s cigarette lighter receptacle. 1 10 Battery clamps cable To supply power to the non-16pin connector from the vehicle’s battery. 1 11 Non-16pin adaptor cable kit To connect to the vehicle equipped (Optional) with non-OBD II management system. 2. For HD-III 1 X-431 V+ tablet Indicates the test result.
LAUNCH X-431 V+ User Manual — General Operations 9 Battery clamps cable To supply power to the non-16pin connector from the vehicle’s battery. 10 Non-16pin adaptor cable kit To connect to the vehicle equipped (Optional) with non-OBD II management system.
X-431 V+ User Manual — General Operations LAUNCH 2 Preparations 2.1 Charging X-431 V+ There are two charging methods available: Via Power adaptor: 1. Insert one end of the included charging cable into the power adaptor. 2. Connect the other end into the charging port of the tablet. 3. Plug the adaptor into AC outlet. Via Personal computer: 1. Insert one end of the data cable (optional) into the Universal Serial Bus port of PC. 2. Connect the other end to the charging port of the tablet.
LAUNCH X-431 V+ User Manual — General Operations period of time, the tool could fail to turn on. Please charge the tool for a minimum of 5 minutes and attempt to turn on again. 2.3.2 Power off Press [POWER] for 3 seconds, an option menu will pop up on the screen. Tap “Power off” to turn the tool off. To perform a forced shutdown, press [POWER] for more than 8 seconds until the screen goes dark. 2.4 Tips on finger operations Single-tap: To select a item or launch a program.
X-431 V+ User Manual — General Operations LAUNCH There are three on-screen buttons available on the bottom of the screen. Back: Tap Home: Tap to return to the previous screen. to jump to the Android’s home screen. Recent App: Tap applications. to view the recently launched applications and running Screenshot: Tap to capture the current screen. 2.6 Adjust brightness Tips: Reducing the brightness of the screen is helpful to save the power of X-431 V+. 1.
X-431 V+ User Manual — General Operations LAUNCH 3 Network Setup Note: Once WLAN is set as ON, the tablet will consume more power. While WLAN keeps unused, please turn it off to conserve battery power. The tablet has a built-in WLAN module that can be used to get online. Once you’re online, you can register your diagnostic App, activate VCI device, update the diagnostic software & APK, surf the Internet, get apps and send email on your network. 3.1 Connect to WLAN 1. On home screen, tap Settings > WLAN.
X-431 V+ User Manual — Vehicle Diagnosis LAUNCH 4 How to diagnose 4.1 Diagnosis Flowchart For new users, please follow the operation chart shown in Fig. 4-1 to get familiar with and start using this tool. Fig. 4-1 4.2 User Registration, Connector Activation & Diagnostic Software Download 4.2.1 User registration Tap the X-431 V+ icon on the home screen to launch the application, and then tap “Login” to enter the login interface of diagnosis software.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-2 1. If you are a new user, tap “New Registration” to enter registration page. See Fig. 4-3. Fig. 4-3 In Fig. 4-3, fill in the information in each field (Items with * must be filled). After inputting, tap “Register”, a screen similar to the following will appear: Fig. 4-4 In Fig. 4-4, input the Serial Number and Activation Code, which can be found in the password envelope.
X-431 V+ User Manual — Vehicle Diagnosis LAUNCH Product SN Product SN Activation code Fig. 4-5 Note: To exit and activate it later, tap “Skip”. In this case, you can activate your connector by tapping “Activate Connector” in “Profile”. For details, please refer to Chapter 4.8.3 Activate Connector. Tap “Activate” to finish your registration. See Fig. 4-6. Fig. 4-6 To download the diagnostic software, tap “Go to Update Center”. See Fig. 4-7. Tap “Download Later” to download and install it later.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-7 In Fig. 4-7, tap “Update” to start downloading. To pause downloading, tap “Stop”. To resume it, tap “Continue”. Once download is complete, the system will install the software package automatically. Note: In process of download, please make sure it is properly connected to the WLAN network. It may take several minutes to finish it, please be patient to wait. 2.
X-431 V+ User Manual — Vehicle Diagnosis LAUNCH 6 Login button/User image: Tap it to login or register the diagnostic system. Once users have logged in successfully, it will change to your username or photo. 4.2.3 Function menu Tap to unfold function menu, it mainly includes the following items: Name Description Diagnostic Configures the tablet to operate as a diagnostic tool. Data Provides abundant automotive technology handbook and repair case for your reference.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis vehicle’s on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. Fig.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis A. Power adaptor: Connect one end of the included power adaptor to DC IN port of X-431 V+ tablet, and the other end to AC outlet. B. Internal battery pack For non-OBDII vehicle, proceed as follows: 1. Locate vehicle’s DLC socket. 2. Select the corresponding non-16pin connector. 3. Plug the non-16pin end of the connector into the DLC socket, and the other end to the OBD I adaptor, and then tighten the captive screws. 4.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis 4.3.3 Vehicle connection (For Commercial Vehicle Version) The method used to connect the VCI module to a vehicle’s DLC depends on the vehicle’s configuration as follows: 1. OBD II Vehicle Connection: Plug one end of the diagnostic cable into the vehicle’s DLC, and the other end into the diagnostic socket of the VCI module, and then tighten the captive screws. Fig. 4-12 2.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-15 *Notes: a). For commercial vehicles, refer to the above connection method to proceed. b). For passenger vehicles, replace the “Non-16pin connector” with “OBD I adaptor” + “non-16pin connector (for passenger vehicles)”. Other connections shall also apply. 4.4 Communication Setup (For Passenger Vehicle Version) There are two kinds of ways available for the tablet to pair with the VCI connector. 1.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis 4.4 Communication Setup (For Commercial Vehicle Version) For Commercial Vehicle version equipped with HD-II, refer to Chapter 4.4.1 for wireless BT pairing. For Commercial Vehicle version equipped with HD-III, there are 2 ways available for the tablet to communicate with the VCI module: wireless BT and WLAN. Choose any one of the following ways to establish communication. 4.4.1 Pairing up via wireless BT Refer to Chapter 4.3.
X-431 V+ User Manual — Vehicle Diagnosis LAUNCH Fig. 4-18 2. Check the box “Use WIFI communication mode”, the system will search for VCI module automatically. See Fig. 4-19 & Fig. 4-20. Fig. 4-19 Fig. 4-20 3. Tap the desired VCI module and a pairing request similar to Fig.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-21 4. Tap “PAIR” to start pairing. Once the pairing is successfully done, the screen displays: Fig. 4-22 5. There are two communication modes available for the VCI module. Work as WIFI hotspot: Once enabled, the VCI module and the tablet automatically connect and form a LAN network to make communication. In this case, the tablet cannot surf the Internet.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-23 Input the network name and access password (if the network is encrypted) until it is properly connected. In this case, the tablet can surf the Internet and communicate with the VCI module.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis 4.5 Start Diagnostics Tap -> “Diagnostic” to enter the vehicle selection page. 2 approaches are provided for you to access the vehicle diagnostic software. Choose any one of the following ways: 1. VINSCAN enables you to access it more quickly. In this case, automatic scan (OBD VIN) and manual input (INPUT VIN) are available. Fig.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-25 Input the VIN, and tap “Confirm” to enter the diagnostic software of the vehicle. 2. Tap a corresponding diagnostic software logo, and then follow the on-screen instruction to access the diagnostic software. Take Demo as an example to demonstrate how to diagnose a vehicle. 1). Tap the “DEMO”, the following dialog box appears: Fig. 4-26 2). Tap “DEMO” to ignore BT connection and jump to the DEMO system selection screen.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis 3). Tap “Engine”, the system will jump to the function menu. Fig. 4-28 4.5.1 Read DTC This function displays the detailed information of DTC records retrieved from the vehicle’s control system. Tap “Read DTC” in function menu, the screen will display the diagnostic result. Fig. 4-29 Note: Retrieving and using DTCs for troubleshooting vehicle operation is only one part of an overall diagnostic strategy. Never replace a part based only on the DTC definition.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis must be followed to confirm the location of the problem. This information can be found in the vehicle’s service manual. On-screen Buttons: New Session: Tap it to return to the home screen. Search: Highlight a certain DTC item, and then tap it to search the definition of the selected DTC online. Report: To save the current data in text format. All reports are saved under the tab “Diagnostic Report” in “My Report” from “Profile” menu.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Note: If you must drive the vehicle in order to perform a troubleshooting procedure, always have a second person help you. Trying to drive and operate the diagnostic tool at the same time is dangerous, and could cause a serious traffic accident. Tap “Read Data Stream” in function menu, the system will display data stream items. Fig. 4-30 On-screen Buttons: Select Page: Tap it to select all items of the current page.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-31 On-screen Buttons: New Session: Tap to return to the home screen. Graph: After selecting, tap it to view the waveform. There are 3 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way. Graph – displays the parameters in waveform graphs. Refer to Fig. 4-32. Fig. 4-32 Value – this is the default mode which displays the parameters in texts and shows in list format.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Combine – this option is mostly used in graph merge status for data comparison. In this case, different items are marked in different colors. See Fig. 4-33. Fig. 4-33 Record: Tap to start recording diagnostic data for future playback and analysis. The saved file follows the naming rule: It begins with vehicle type, and then the record starting time and ends with .x431 (To differentiate between files, please configure the accurate system time).
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis 4.5.5 How to view History? Generally once a vehicle diagnosis is performed, X-431 V+ will record the every details of diagnostic process. The History function provides a quick access to the tested vehicles and users can resume from the last operation, without starting from scratch. 1. Tap “History”, all diagnostic records will be listed on the screen in date sequence.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis to reset the service lamp. Steering Angle Calibration 1. To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. 2.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Battery Register/Battery Maintenance This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. Battery matching must be performed in the following cases: a) Main battery is replaced.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. DPF regeneration may be performed in the following cases: a) The exhaust back pressure sensor is replaced. b) The PM trap is removed or replaced. c) The fuel additive nozzle is removed or replaced.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-34 By default, all diagnostic software is selected. To select certain software, tap “Unselect”, and then uncheck the box next to car make. Tap “Update” to start downloading. Once downloading is finished, the software packages will be installed automatically. 4.8 Profile This function allows users to manage your personal information. 4.8.1 My connector This option is used to manage all your activated connectors.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-35 * Note: please be sure to keep the VCI connector powered on while performing the operation. 4.8.3 Activate connector It is used to activate your diagnostic connector. Input the Serial Number and Activation Code, and then tap “Activate” to activate the connector. For details on how to obtain Serial Number and Activation Code, tap the link below to get help. 4.8.4 Firmware fix Use this item to upgrade and fix diagnostic firmware.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis 4.9 Settings It enables you to make some application settings and view software version information etc. 4.9.1 Units of measurement It is designed to set the measurement unit. Metric System and English System are available. 4.9.2 Orientation This option is used to set the display mode of the application. 4.9.3 Print information This option lets you define your print information. It mainly includes Workshop, Address, Telephone, Fax and License Plate.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis & [FEED] for 8 seconds, the following resetting command will be printed out: at + default = 1 ok at + reboot = 1 rebooting... 3. Tap “Reset” to configure Wi-Fi printer. Step 1: Connect the printer: Tap “Scan” to select the desired printer hotspot named with X-431PRINTER-XXXX (XXXX stands for 4 characters), and then tap “Connect” to enter Step 2. Fig.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis Fig. 4-38 4. Once the Wi-Fi network of the printer is connected and the printer is found, tap “Printing test” to test the printing. Fig. 4-39 Now you can use the Wi-Fi printer to print! If the printer is not found, please reset the printer to default factory settings (refer to Step 2 for details) and check whether the current device and the printer are on the same LAN.
LAUNCH X-431 V+ User Manual — Vehicle Diagnosis B. If you have configured the Wi-Fi printer to the LAN: 2. Tap “Connect to Printer”: a). If the local network remains as it is, tap “Test Print” directly to test the printing. b). If the local network changes, you have to reset the Wi-Fi printer. 4.9.5 Diagnostic feedback This item allows you to feedback your diagnostic problems to us for analysis and troubleshooting. 4.9.
X-431 V+ User Manual — Others LAUNCH 5 Others 5.1 Email The function allows you to send and receive email. 5.1.1 Configure an email account Note: Before sending or receiving email, you have to set up an email account. In addition, this function required a stable network connection. 1. On the home screen, tap Email. 2. Choose the desired email account type. 3. Input email address and password, tap “Next”.
X-431 V+ User Manual — Others LAUNCH 1 Return to the previous page. 2 Advance to the recently visited page. 3 Refresh the current page. 4 Close the current page. 5 Create a new tab. 6 Input a web address. 7 Add the current page as bookmark. 8 Open search bar. 9 Open bookmark list. 10 View more options. 5.2.2 Download files Files, pictures, and applications can be downloaded from the website in browser.
X-431 V+ User Manual — Others LAUNCH 5.3.2 Run on PC Perform the following steps: Locate the new disc. Copy the files. 5.3.3 Install an application Do the following steps: 1. Tap Settings > Security, and set the “Unknown sources” to ON, which allows you to install apps from unknown sources. 2. A dialog box appears on the screen, tap “OK” to confirm. 3. Set the tool as “Connected as a media device”, and copy the APK file from the PC to the tool. 5.
X-431 V+ User Manual — Others LAUNCH 6 FAQ 1. Communication error with vehicle ECU? Please confirm: 1) Whether the VCI is properly connected. 2) Whether the vehicle ignition switch is ON. 3) If all checks are normal, send vehicle year, make, model and VIN number to us using Dia. Feedback feature. 2. Failed to enter into vehicle ECU system? Please confirm: 1) Whether the vehicle is equipped with the system. 2) Whether the VCI is correctly connected. 3) Whether the vehicle ignition switch is ON.
X-431 V+ User Manual — Others LAUNCH Item 5 in this Chapter). 3. Tap “Settings” -> “WLAN”, slide the switch to ON and then choose the desired WLAN network to connect. 4. Open the browser and visit www.dbscar.com to download and install the latest App. 5. After the installation is complete, launch the application and login with your username and password. 6. Tap -> “Update” to download the diagnostic software.
Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. LAUNCH electronic product is warranted against defects in materials and workmanship for one year from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use.
Attn: Customer Service Department LAUNCH TECH. CO., LTD. Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian, Longgang, Shenzhen, Guangdong P.R.China, 518129 Launch website: http://www. cnlaunch.com http://www.x431.com Statement: LAUNCH reserves the rights to make any change to product designs and specifications without notice. The actual object may differ a little from the descriptions in the manual in physical appearance, color and configuration.
