CROSSOVER SERIES In a class by itself MODEL N O. WHWF09810M/NM MODEL N O. E HWF09810M/NM 7 W A S H E R I N S T A L L AT I O N M A N U A L 3 Laundrylux DOC. NO. DOC. NO.096417 096417 EDITION 13.2011 EDITION 13.
ATTENTION INSTALLER Fig. For coin-operated models, the coin meter housing is packed UNDER 1 the machine. DO NOT DISCARD THE PACKING MATERIALS without first removing the meter housing! See installation instructions later in this manual for details. 1 Coin meter housing ATTENTION INSTALLER Four transportation bolts are installed in the rear of the machine, to protect the suspension and tub assembly from damage during shipment.
Installation manual WHWF09810M/NM EHWF09810M/NM WARNING: ALL OPERATING AND MAINTENANCE PROCEDURES SHOWN ON THE NEXT PAGE OF THIS MANUAL MUST BE FOLLOWED DAILY FOR PROPER OPERATION OF YOUR MACHINE. PLEASE ENTER THE FOLLOWING INFORMATION AS IT APPEARS ON THE MACHINE(S) DATA PLATE(S). MACHINE TYPE OR MODEL MACHINE SERIAL NUMBER(S) ELECTRICAL CHARACTERISTICS: ________ VOLTS, _______ PHASE, _______ HZ. KEEP THIS MANUAL IN A SECURE PLACE FOR FUTURE REFERENCE.
Intentionally blank
SAFETY AND WARNINGS SIGNS Replace If Missing Or Illegible One or more of these signs must be affixed on each machine as indicated, when not included as part of the front instruction panel.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES MESURES DE SECURITE WARNING To reduce the risk of fire, electric chock, or injury to persons when using your appliance: AVERTISSEMENT Pour réduire les risques d´incendie, de choc électrique ou de blessure quand, I´appareil est utilisé: 1. Read all instructions before using the appliance. Lire toutes les instructions avant d’utiliser l’appareil. 2. This machine must be installed according to the installation instructions.
NOTICE TO: OWNERS, OPERATORS AND DEALERS IMPROPER INSTALLATION AND INADEQUATE MAINTENANCE, POOR HOUSEKEEPING AND WILLFUL NEGLECT OR BYPASSING OF SAFETY DEVICES MAY RESULT IN SERIOUS ACCIDENTS OR INJURY. TO ASSURE THE SAFETY OF CUSTOMERS AND/OR OPERATORS OF YOUR MACHINE, THE FOLLOWING MAINTENANCE CHECKS MUST BE PERFORMED ON A DAILY BASIS.
NOTICE TO INSTALLER Improper installation of this machine: • • • • May cause serious damage to the machine. May result in other property damage. May cause personal injury. Will void the manufacturer's warranty. Location Requirements • The location for your washer should have a flat and even floor. This will improve performance, minimize noise and decrease washer movement. • The unit can be installed in a laundry room, or other recessed area. Additional Requirements • A grounded electrical outlet.
Contents Contents Technical data........................................................................................... 1:1 Installation ................................................................................................. 2:1 Water connections ............................................................................... 3:1 Drain connection .................................................................................. 4:1 Connection of external liquid supplies .......................
Intentionally blank
Technical data Technical data WHWF09810M/NM EHWF09810M/NM Innerdrum volume diameter litres/ft 3 mm/inch 98/3.5 554/21 4/5 Drum speed wash extraction rpm max rpm 45 1000 306 G-factor Weight, net kg/lbs 136/300 WHWF09810M/NM EHWF09810M/NM Connections Water valves connection DN20 3/4" GH Rec. water pressure psi kPa 30-90 200-600 Functioning limits psi for water valve kPa Capacity at 45 psi (300 kPa) gallon/min liter/min 8-145 50-1000 Drain hose Draining capacity 2.
Technical data 1:2 1 2 3 4 5 6 7 8 9 Power line Air Vent for Safety Hot water Cold water Drain Coin meter (coin operated models only) Control panel Detergent dispenser Door E 6 7 1 2 3 4 5 8 A B C D F NOTES : A 1109mm = 43 5/8 inch B 1010mm = 39 3/4 inch C 592mm = 23 3/8 inch D 293mm = 11 1/2 inch E 686mm = 27 inch F 756mm = 29 7/8 inch
Installation 2:1 Installation For safety,two people should install this product. Leave the machine on the transport pallet until it can be placed in the final, prepared position. First remove all the packing materials. Upon opening of the package, water drops may be seen on the plastic bag and the drum. This is a normal phenomenon resulting from water tests in the factory. NOTE: 1. A bottom cover plate is wrapped in the top of the packing material. 2. A coin meter housing is wrapped in the base.
Installation 2:2 Transportation Bolts The washer is fitted with transportation bolts to prevent internal damage during transportation. Transportation bolts must be removed before using the washer. Removing Transportation Bolts Fig. 1. Unscrew the 4 bolts with a wrench. Remove the lower 2 bolts first, then the upper two. 2 One of the bolts retains the power cord of the washer to prevent operating without removing bolts. 2 2. Remove the bolts and the sleeves to release the power cord.
Installation 2:3 Siting Install the machine close to a drain standpipe or floor drain,and within 4 feet of the water supply spigots. In order to make installation and servicing the machine easier the following clearances are recommended: Fig. 噝 At least 20 inches (500 mm) between the machine and the wall behind. 噝 Minimum 1 inch (25 mm) to next machine if more than one machine is installed in a row. Floor 噝 The floor must be smooth and hard.
Intentionally blank
Installation Water connections All inlet connections to the machine are to be fitted with manual shut-off valves and filters, to facilitate installation and servicing. NOTE: The inlet filter screens are provided inside the machine's connection fittings. Water pipes and hoses should be flushed clean before installation. After installation, hoses should hang in gentle arcs. Hoses are to be of an approved type and grade, to comply with national regulations.
Installation 3:2 Water type Water connection 1 Fig.
Installation Drain connection Connect the machine’s drain hose to the back of the washer, using the spring clamp provided in the accessories package. Avoid sharp bends in the hose which may prevent proper draining. Fig. 1 You can connect the drain hose to a sewer stand pipe. If you do this, make sure that the outlet hose will not come out of the stand pipe. You can connect the drain outlet to a sink or basin. If you do this, make sure the outlet hose will not come out of the sink or basin. 1 C A. B. C.
Intentionally blank
Installation Electrical installation must be carried out by licensed, qualified personnel! 5:1 All optional equipment connected must be EMC-approved to EN 50081-1 or EN 500822. Connection of external price reduction control signal Fig. 1 The accessories package includes a two-wire harness for price reduction (promotion) activation. The harness mates with a connector on the machine's front main control circuit board. The price reduction harness carries a +5VDC signal lead, and a ground lead.
Installation 5: 2 Electrical Connections This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounded plug. The plug must be inserted into an outlet that is properly installed and grounded. • Improper use of the plug can result in a risk of electric shock.
Function checks Function checks Perform the following checks once the machine is installed: 噝 Open the water supply valves. 噝 Press the START button or, if needed, insert coins and press START. Check: 噝 that the drum rotates normally and that there are no unusual noises. 噝 that there are no leaks in water supply/drain connections. 噝 that water passes through the detergent compartment and fabric condi tioner compartments. 噝 that the door cannot be opened using reasonable force during a program.
Intentionally blank
Preventive maintenance To keep your machine in proper working order, follow the preventive maintenance recommendations provided below. The maintenance interval should be adjusted according to machine usage. Daily 噝 Check the door and door lock: - Open the door and try starting the machine. The machine MUST NOT START. - Close the door, start the machine and try opening the door using reasonable force.
8:1 Installation . OPL MODE SETUP To convert the machine for OPL operation, the front control / display module must be reset to “coin mode” and the prices of all six cycles and options must be set to $0.00. Fig 1 Reset Control / Display Module Method A 1. Remove top cover of machine. (Secured with two T15H security Torx fasteners). 2. Locate small “red” reset button behind the left digit in the display. Press and hold down button. 3.
4. Press four program buttons, COLD, WARM, HOT, & DELICATE to set price to 0.00 Each button increments a corresponding digit, left to right, in the price. Each digit rolls over from 9 to 0 without affecting other digits. The left-most digit cannot be programmed to “0”, but can be blanked out. 5. Press START to save value 6. Press WARM and repeat steps 3-5. Repeat until all of the programs and options (six total) are set to zero. 7. Press and release service mode switch to return normal mode. 8.
Established in 1955, Wascomat has sold more commercial washers than anyone else in the industry. Wascomat’s years of service have made it the most trusted name in commercial laundry. The heritage of the Wascomat brand is rooted in the origin of the Self Service, OPL and Facility Management laundry industry. Everyday across North America, customers choose Wascomat equipment for all their laundry needs. Having updated your laundry with Wascomant is a wise choice for many reasons.
