Installation Guide

Multi-Piece Sectional Product
Installation Instructions
4. Using a clean rag, wipe off excess water and caulk.
Figure 30
INSTALLATION INSTRUCTIONS FOR SHOWER SEATS WITH
SWING DOWN LEGS
(This style seat has four (4) adjustable height legs)
Your seat with swing down legs is fully assembled. Remove it from
the box and proceed as follows:
1. Choose the height of the seat you want. Barrier Free style
showers will typically have fold up seat installed at 17” to 19” height.
2. After selecting the height you desire, adjust each of the four legs
to that height while maintaining the seat in a level position. Lock
each of the lock nuts.
3. Place the seat against the wall of the shower where you want the
seat to be located. Seat may be centered on the wall for a Barrier
Free installation.
4. With the seat placed against the mounting wall, position the
two hinges to the wall. Using a pencil, mark the three holes (3)
holes in the ange onto the wall for each hinge. Remove seat
from wall.
5. Using a power drill with a 0.120” diameter drill through the
wall the three (3) mounting holes for each ange.
6. Apply silicone caulking around and inside each drilled hole
before installing the seat.
7. Place the seat against the mounting wall with each hinge
aligned to the mounting holes. Utilizing the six (6) #10 x 2”
Stainless Steel screws, place a Phillips screw driver into your
power drill and securely tighten each of the six (6) screws.
THIS COMPLETES THE INSTALLATION OF THE SEAT
INSTALLATION INSTRUCTIONS FOR GRAB BARS
Recommended tools for installation:
1/4” Power Drill
1/8” drill bit when drilling through berglass
#2 Phillips Screw Driver and/or Phillips drill insert
1/2” Open end wrench or a small Crescent wrench
Tape measure
Pencil/pen
Center Punch
Silicone Caulk
1. As indicated earlier in this manual, wood reinforcements must
be solidly installed behind the tile wall surface to provide a secure
mounting surface to attach the grab bars. Grab bars must be
installed at these locations only.
2. Select the particular size and style of grab bar you want to
install. Certain grab bars have snap in place ange covers, and
others have exposed anges.
3. For grab bars with snap in place ange covers, use the handle
of a Phillips screw driver to tap back the covers on the bottom
edge of the covers. It will be convenient in the installation process
if the covers are tapped together in the center of the grab bar.
4. Determine the position you want the to install the bar. Place
the bar against the wall. Using a pencil, mark the location of each
mounting hole at both ends of the bar.
5. Using a power drill with a 1/4” diameter carbide tipped drill bit,
drill, each mounting hole.
Materials Required:
Acrylic Latex Caulk
Wiping Cloths (Rags)
Clean Water
Cut off tip of caulk tube diagonally with opening
no larger than 1/8”.
(Figure 27)
Run a continuous bead of caulk at the seam between
the two parts.
(Figure 28)
Smooth caulk gently with a wet fingertip. (Figure 29)
Using a clean rag, wipe off excess water and caulk.
(Figure 30)
12
Seam Caulking Instructions
Figure 27
Figure 28
Figure 30
Figure 29
Tools Required:
Caulking Gun
Cup
Your seat with swing down legs is fully assembled. Remove it from the box and proceed as follows:
(This style seat has four (4) adjustable height legs)
1.- Choose the height of the seat you want. Barrier Free style showers will typically have fold up
seat installed at 17” to 19” height.
2.- After selecting the height you desire, adjust each of the four legs to that height while
maintaining the seat in a level position. Lock each of the lock nuts.
3.- Place the seat against the wall of the shower where you want the seat to be located.
Seat may be centered on the wall for a Barrier Free installation.
INSTALLATION INSTRUCTIONS FOR SHOWER SEATS
WITH SWING DOWN ADJUSTABLE LEGS
4.- With the seat placed against the mounting wall, position the two hinges to the wall.
Using a pencil, mark the three holes (3) holes in the flange onto the wall for each hinge.
Remove seat from wall.