OPERATOR'S MANUAL EN p. 2 16 Inch / 10 Amp Tiller / Cultivator TE1016M TE1016M Read all safety rules and instructions carefully before operating this tool.
CONTENTS CONTENTS 2 PRODUCT SPECIFICATIONS 2 SAFETY INFORMATION 3-6 SPECIFIC SAFETY INFORMATION 7-8 SYMBOLS 9-10 KNOW YOUR TILLER / CULTIVATOR 11 UNPACK 12 ASSEMBLY 13-14 OPERATING 15-17 MAINTENANCE 18-19 STORAGE 19 TROUBLESHOOTING 20 WARRANTY 21 EXPLODED DIAGRAM 22-23 PARTS LIST 24 NOTES 25 PRODUCT SPECIFICATIONS Model : TE1016M Nominal Voltage : 120V~60Hz Tilling Width : 16” (400mm) Maximum Tilling Depth : 9” (220mm) Nominal Current : 10(A) Number of tines : 6 T
SAFETY INFORMATION TO REDUCE RISK OF INJURY: Before any use be sure everyone using this product reads and understands all safety instructions and other information contained in this manual. CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
SAFETY INFORMATION DOUBLE INSULATION - The tiller/cultivator has double insulation. This means that all external metal parts are insulated from the electrical supply. This is achieved by introducing an insulation layer between electrical and mechanical parts. The double insulation guarantees you the greatest possible safety. • EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord be sure it is heavy enough to carry the current your product will draw.
SAFETY INFORMATION • DON'T ABUSE CORD - Never carry this product by the cord or yank the cord to disconnect from the receptacle. Keep cord from heat, oil, and sharp edges. • USE RIGHT APPLIANCE - Do not use this product for any job except that for which it is intended. • DON'T OVERREACH - Guide the tiller/cultivator at a walking pace only. Keep proper footing and balance at all times. • LIGHTING - Only operate your tiller/cultivator in daylight or good artificial light.
SAFETY INFORMATION WARNING: Do not operate the tiller/cultivator near underground electrical cables, telephone lines, pipes or hoses. If the tiller/cultivator strikes a foreign body, turn it off immediately, wait for the tines to stop and check for damage. If necessary, repair before restarting. If the tiller/cultivator starts to vibrate abnormally, turn it off immediately and check for the cause. Vibration is generally a warning of trouble.
SPECIFIC SAFETY INFORMATION Training 1. Read the operating and service instruction manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction. 3. Keep the area of operation clear of all persons, particularly small children, and pets. 4.
SPECIFIC SAFETY INFORMATION 9. Never operate the machine without proper guards, plates, or other safety protective devices in place. 10. Keep children and pets away. 11. Do not overload the machine capacity by attempting to till too deep at too fast a rate. 12. Never operate the machine at high transport speeds on hard or slippery surfaces. 13. Never allow bystanders near the unit. 14.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING Indicates a potentially hazardous situation, which, if not avoided,could result in death or serious injury. CAUTION Indicates a potentially hazardous situation, which, if not avoided,may result in minor or moderate injury.
KNOW YOUR TILLER / CULTIVATOR 1 2 14 3 5 6 4 7 10 8 9 12 11 13 1 Main Handle 8 Motor Housing 2 Cord Retainer 9 Motor Support Plate 3 Power Plug 10 Lower Handle Section 4 Cable Clip 11 Tine Assembly (right/left) 5 Upper Handle Assembly 12 Transport Wheels 6 Cam Lock Assembly 13 R Clip 7 Center Handle Section 14 Locking Button 11
UNPACK 1. Unpack all parts and lay them on a flat, stable surface. 2. Remove all packing materials and shipping devices if applicable. 3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. Using an incomplete or damaged product represents a hazard to people and property. 4. Ensure that you have all the accessories and tools needed for assembly and operation.
ASSEMBLY M6X57 M6X57 O6 O6 O5 O5 M5X12 Fig.
ASSEMBLY This product must be assembled correctly before use. 1. Remove the plane washers (O5) ,wave washers (O5) and screws ( M5x12 ) from wheel axis of tiller,then place one wheel (12) over each side of axle, then attach using O5 plane washer (O5) ,wave washer (O5) and screws ( M5x12 ) to secure (Fig1-1). 2. Press the wheel covers into the wheel and cover the O5 M5X12 ends of the axles. A rubber mallet may be used to seat them securely onto the wheels (Fig1-1). Fig1-1 3.
OPERATING STARTING: 1. Make sure the wheel frame is raised before you start the tiller. To raise the frame, pull out the Locking button (Step A); rotate the wheel frame upward (Step B); release the Locking button. The wheel frame will be locked in place by the Locking button (Fig.2). 2. Secure the extension cord into the cord retainer (2). The loop of the extension cord must be long enough for the cord retainer to freely slide from one side to the other.
OPERATING 5. To prevent tripping, take extra precautions when moving backwards and when pulling the tiller / cultivator back toward yourself. 6. If the tiller/cultivator digs deep enough to stay in one spot, gently rock it side to side until it starts moving forward again. Never pass the tiller/cultivator over the extension cord. 7. Make sure the cord is always in a safe position behind you. 8. When working on inclines always stand diagonally to the incline to retain a firm, safe footing. 9.
OPERATING Before use, remove any visible stones or other foreign bodies from the area. CAUTION: Before moving the tiller/cultivator from one area to another switch off the motor and wait for the tines to come to a complete stop. Be careful not to let the tines touch the ground while moving the tiller/cultivator. The tines as well as the unit itself may be damaged even if the motor is switched off.
MAINTENANCE BEFORE CARRYING OUT MAINTENANCE OPERATIONS, DISCONNECT POWER SUPPLY. Before each use check the extension cord for signs of damage or ageing. Replace the cable if it is cracked, split or otherwise damaged. Check the condition of the tines and ensure that all threaded connections are securely tightened. If the tines become dull or blunt, sharpen or replace them. Call our customer service help line. Once per season lubricate the tines and shaft.
MAINTENANCE WARNING: Injury can occur while working on the tines. Wear protective gloves. To remove the complete tine assemblies from the shaft, remove the B shape fixed pin (13)from the shaft. Remove the tine assembly from the shaft. Reverse above steps to install tines. ADDING TRANSMISSION LUBRICANT (FIG.7): Drain screw plug is located on the right side of transmission housing.
TROUBLESHOOTING Problem Possible causes Remedy Motor does Unit not plugged in Plug in the unit not start No electricity Check power supply Defective cable Check cable.Repair or replace if required Defective safety switch/plug Arrange for repair Overheat protection activated 1. Working depth too large, set to a shorter depth. 2. Tines blocked, remove the blockage. 3. Soil too hard, select correct work depth and move forward and backward several times while slowing down the operation speed.
WARRANTY We take pride in producing a high quality, durable product. This Lawnmaster® product carries a limited two (2) year warranty against defects in workmanship and materials from date of purchase under normal household use. If product is to be used for commercial, industrial or rental use, a 30 day limited warranty will apply. Warranty does not apply to defects due to direct or indirect abuse, negligence, misuse, accidents, repairs or alterations and lack of maintenance.
EXPLODED VIEW 48 47 46 45 44 43 49 42 50 51 41 52 53 69 40 54 39 55 38 56 57 58 71 37 36 35 59 72 34 60 33 61 62 32 63 31 30 29 28 27 26 14 13 25 22 24 12 23 Right Side Tine Assembly (B) 11 10 21 9 20 19 8 18 7 17 6 16 5 15 22 2 1 4 3 Left Side Tine Assembly (A)
EXPLODED VIEW 68 67 70 66 65 64 23
PARTS LIST Part No. Part Name QTY’ Part No.
NOTE 25