User's Manual

A. LAN Settings
B. HTTP
[
C. Network Test
[IP Type]: There are two options: “Fixed IP Address” and “dynamic IP Address”.
After selecting an Internet connection setting - such as fixed IP address (static) or dynamic IP
address (DHCP) – and allocating a port, users can access the indoor unit remotely via the
Internet.
1)If fixed IP address has been selected, it is necessary to set up an IP address, a subnet mask
and a gateway.
[IP Address]: Enter the IP address in this field.
[Subnet Mask]: Input numbers for the subnet mask.
[Gateway]: Enter numbers for the default gateway.
[DNS Type]: Options include “Manual DNS” and “From DHCP Server”. If users select “Manual
DNS”, they have to input numbers for primary DNS and second DNS manually.
2)If DHCP is selected, the server will allocate a IPC IP address automatically.
Save the IP address when selecting DHCP and the IPC will automatically connect with
the server. It will allocate an IP address when the connection is stable, and this address will
be displayed on the interface.
HTTP Port]: The IP address identity one indoor unit in the network, you can run several
programs on this equipment, and every program will transfer the data through some port, in fact
data is transferred from one port to another. The port setting of this page is asking user choose
which port to transfer the data for the web server. Doing port mapping, need to maintain
consistent with the port (equipment factory default port is 80).Sets up a Web browser port via
HTTP. The default port number is “80”.
[Mobile port]: Mobile monitoring port. And default value is 20510.
[Wan Test]: In this field, users can fill in the IP address or DDNS address which they set up,
and click “ ” to test the network traffic is normal or not. If all the network parameters are
set correctly, click “ ”
and “Test Success!” will be shown. Otherwise “Test Failure!” will
be shown.
NOTE:
2.7.3.1 Network--Basic Settings
Click “Parameters—Network—Basic Settings” to enter the LAN Settings interface. Default IP
address of the equipment is 192.168.0.111. The user can set up device network parameters
through the operation “Quick Setting Guide”, user can change it according to your network
environment.
2.7.3.2 Network--DDNS
Click “Parameters-Network-DDNS”to enter the DDNS setting interface. DDNS setup as follows.
User can use third part DDNS, first user must have a domain name; or
is recommended. Please remember the username, password and domain name.
Then enable DDNS, for example, select the DDNS Provider as “3322.org”. If your domain name
is “test.f3322.org”, please enter “test.f3322.org” in the option “Your Domain”, the “Username” and
“Password” is the username and password that applied in the . Click “ ” to
save. Then you can access the device by domain name.
www.dyndns.org
www.3322.org
www.3322.org
2.7.3.3 Network--Wifi(Optional, please take actual machine as quasi)
For the indoor unit with WIFI function, users can visit the device remotely by the following
methods: through network cable connection or through wireless connection. If through wireless
connection, please use the network cable to connect the device into LAN before doing settings
of wireless connection. Then click “Parameters—Network—WiFi” to enter the Wifi Setting
interface, and according to the below 1-6 steps to do the settings.
1) Open wireless, “ ” indicates WIFI status to be enabled.
2) Click the “ ” button to search the current wireless routers, and all the wireless routers
will appear on the Current Hot Point list.
3) Choose one effective router, click it to choose router SSID.
4) Input correct password of the wireless router in wireless security mode.
5) Click “ ” to check the wireless network is connected successfully or not.
6)When the wireless is connected successfully, click “ ” to save the settings, the device
will be reboot automatically, take away the Ethernet cable, then the wireless network will work
perfectly.
27
28
Note:
1. When adjust WIFI status, the device will reboot after saving the setting.
2. When enable WIFI status, the device will reboot automatically if plug or unplug the crystal head
of network cable to the RJ45 ethernet interface of the indoor unit.
3. Through Wifi connection, the “Network Type” on the Network Basic Setting suggested to be set as
“DHCP”. When configure the parameters about WIFI, user can view the indoor unit can be
allocated
IP address whether or not through the search tool “HiCamSearcher”.