Installation Guide

To register your fixture, please visit our website: SeaGullLighting.com
To register your fixture, please visit our website: SeaGullLighting.com
To register your fixture, please visit our website: SeaGullLighting.com
IMPORTANT SAFETY INSTRUCTIONS
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty,
listing and create a potential safety hazard.
• Caution risk of fire. Please keep surface of LED a minimum of
1.5 inches away from combustible materials.
• Install cable so that caution printed on cable is visible after
installation.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Turn off electrical power before modifying the lighting system in
any way.
• This LED retrofit module is a listed component of Sea Gull
Lighting’s Ambiance
®
Lighting System.
• This LED module may be dimmed. We recommend confirming
the dimming control is compatible with the low voltage power
supply being used.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty,
listing and create a potential safety hazard.
• Caution risk of fire. Please keep surface of LED a minimum of
1.5 inches away from combustible materials.
• Install cable so that caution printed on cable is visible after
installation.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Turn off electrical power before modifying the lighting system in
any way.
• This LED retrofit module is a listed component of Sea Gull
Lighting’s Ambiance
®
Lighting System.
• This LED module may be dimmed. We recommend confirming
the dimming control is compatible with the low voltage power
supply being used.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty,
listing and create a potential safety hazard.
• Caution risk of fire. Please keep surface of LED a minimum of
1.5 inches away from combustible materials.
• Install cable so that caution printed on cable is visible after
installation.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Turn off electrical power before modifying the lighting system in
any way.
• This LED retrofit module is a listed component of Sea Gull
Lighting’s Ambiance
®
Lighting System.
• This LED module may be dimmed. We recommend confirming
the dimming control is compatible with the low voltage power
supply being used.
SAVE THESE INSTRUCTIONS
HC-1715FS 110510
HC-1715FS 110510
HC-1715FS 110510
Apply Pressure Here
Exercer une pression à ici
Ponga Presión Aquí
Apply Pressure Here
Exercer une pression à ici
Ponga Presión Aquí
Apply Pressure Here
Exercer une pression à ici
Ponga Presión Aquí
ETL LISTED
CONFORMS TO
ANSI / UL STD 2108
CERTIFIED TO
CAN/CSA STD C22.2
NO.250.0
4000888
50mm x 25mm
ETL Defond.qxd 10/15/10 1:08 PM Page 1
ETL LISTED
CONFORMS TO
ANSI / UL STD 2108
CERTIFIED TO
CAN/CSA STD C22.2
NO.250.0
4000888
50mm x 25mm
ETL Defond.qxd 10/15/10 1:08 PM Page 1
ETL LISTED
CONFORMS TO
ANSI / UL STD 2108
CERTIFIED TO
CAN/CSA STD C22.2
NO.250.0
4000888
50mm x 25mm
ETL Defond.qxd 10/15/10 1:08 PM Page 1
Before You Begin
• For retrotting electronic transformer installation: Due
to electronic transormer minimum load requirements, a
60 watt zero-load transformer (96223S) is available for
retrofitting the power supply in addition to the lamp.
• If your system is powered by a magnetic power supply,
confirm the boost tap feature is not being used.
• If boost tap is being used, have a qualified electrician redo
the 120V connections so the boost tap is not used. Use
of the boost tap to supply the LED Festoon module may
reduce the useful life of the LED & void your warranty.
Installation Instructions
1. Remove existing festoon lamp.
2. Gently apply pressure to contacts of LED module so lamp
holder clips secure the LED module in place.
3. Energize power unit.
Before You Begin
• For retrotting electronic transformer installation: Due
to electronic transormer minimum load requirements, a
60 watt zero-load transformer (96223S) is available for
retrofitting the power supply in addition to the lamp.
• If your system is powered by a magnetic power supply,
confirm the boost tap feature is not being used.
• If boost tap is being used, have a qualified electrician redo
the 120V connections so the boost tap is not used. Use
of the boost tap to supply the LED Festoon module may
reduce the useful life of the LED & void your warranty.
Installation Instructions
1. Remove existing festoon lamp.
2. Gently apply pressure to contacts of LED module so lamp
holder clips secure the LED module in place.
3. Energize power unit.
Before You Begin
• For retrotting electronic transformer installation: Due
to electronic transormer minimum load requirements, a
60 watt zero-load transformer (96223S) is available for
retrofitting the power supply in addition to the lamp.
• If your system is powered by a magnetic power supply,
confirm the boost tap feature is not being used.
• If boost tap is being used, have a qualified electrician redo
the 120V connections so the boost tap is not used. Use
of the boost tap to supply the LED Festoon module may
reduce the useful life of the LED & void your warranty.
Installation Instructions
1. Remove existing festoon lamp.
2. Gently apply pressure to contacts of LED module so lamp
holder clips secure the LED module in place.
3. Energize power unit.
Customer Care Center
800-347-5483
SeaGullLighting.com
Customer Care Center
800-347-5483
SeaGullLighting.com
Customer Care Center
800-347-5483
SeaGullLighting.com