Installation Guide

IMPORTANT SAFETY INSTRUCTIONS
• Besuretheelectricitytothesystemyouareworkingonis
turnedoff;eitherthefuseremovedorthecircuitbreakersetat
off.
• Useofothermanufacturerscomponentswillvoidwarranty,
listingandcreateapotentialsafetyhazard.
• Ifyouareunclearastohowtoproceed,contactaqualied
electrician.
• Properwiringisessentialforthesafeoperationofthisxture.
• Youdon’tneedspecialtoolstoinstallthisxture.
• Besuretofollowthestepsintheordergiven.
• NorelampingforLEDluminaire.
• Donotlookdirectlyatlightedbulb.
• Thisxtureisforundercabinetuseonly.
• CAUTION–Toreducetheriskofre,electricshock,orinjuryto
persons:
a.Useonlyinsulatedstaplesorplastictiestosecurecords;
b.Routeandsecurecordssothattheywillnotbepinchedor
damagedwhenthecabinetispushedtothewall;
c.Positiontheportablecabinetlightwithrespecttothecabinet
sothelampreplacementmarkingsareabletobereadduring
relamping;NA–NorelampingforLEDluminaire.
d.Notintendedforrecessedinstallationinceilings,orsoffits;
and
e.TheNationalElectricalCode(NEC)doesnotpermitcordsto
beconcealedwheredamagetoinsulationmaygounnoticed.
Topreventredanger,donotruncordbehindwalls,
ceilings,soffits,orcabinetswhereitmaybeinaccessiblefor
examination.Cordsshouldbevisuallyexaminedperiodically
andimmediatelyreplacedwhenanydamageisnoted.
• Readinstructionscarefully.
SAVE THESE INSTRUCTIONS
Transformer Installation
Note- Do not exceed the wattage limitations for the transformer
you select.
6. Plug connecting cord from the transformer into the first LED
puck light of run or connecting hub.
7. Bundle excess cord neatly and secure.
Before You Begin
1. Carefully remove the fixture from the carton and check that
all parts are included, as shown in figure 1. Be careful not
to misplace any of the screws or parts which are needed to
install this fixture.
Installation (Surface Mounting)
1. Make sure connecting cables are properly plugged in before
installation.
2. Raise LED puck housing to desired mounting location.
3. Tighten support screws to secure housing to mounting
surface.
Surface Mounting (No Exposed Wires)
1. Drill 5/16" diameter hole and feed connecting cables through.
2. Make sure connecting cables are properly plugged in before
installation.
3. Raise LED puck housing to desired mounting location and
position over the hole with cables.
4. Tighten support screws to secure housing to mounting
surface.
Installation (Recessed Mounting) 2 3/8"
diameter hole
1. Install support springs with screws provided.
2. Make sure connecting cables are properly plugged in before
installation.
3. Feed connecting cables through openings.
4. Position the puck housings over the designated opening and
press in place.
Interconnecting LED Pucks
1. Pucks are provided with 36" interconnecting cords (other
lengths can be purchased separately).
2. LED Puck can be daisy chained (interconnected) up to 30W
of total power.
3. LED Pucks can be powered from the connecting hub (6 LED
pucks max. per hub).
Hub Connection
Raise hub to desired mounting position and secure with support
screw.
4. Plug in the cables from LED Pucks.
5. Plug in cable from transformer.
Helpful Tools
Outils Utiles
Herramientas Útiles
HC-1887FS 020812
SurfaceMounting/MontageenSurface/MontajedeSupercie
ConnectingHubtoLxSystem
RelierlePlotauSystèmeLx
ConectandoelConcentradoralSistemaLx
ConnectingHubtoRemoteTransformer
RelierlePlotauTransformateuràDistance
ConectandoelConcentradoralTransformador
Remoto
ConnectingHubtoTransformer
RelierlePlotauTransformateur
ConectandoelConcentradoralTransformador
ConnectingHubtoPlug-InTransformer
RelierlePlotauTransformateurEnchable
ConectandoelConcentrador
alTransformadordeEnchufe
RecessedMounting/MontageEncastré/MontajeEmpotrado
9488notsupplied
9488nonfourni
9488noincluido
96223Snotsupplied
96223Snonfourni
96223Snoincluido
9459notsupplied
9459nonfourni
9459noincluido
s
s
s
PuckscanbeconnectedtoSGLLXsystem
poweredwithSGLListedClass1andClass2
powersuppliesonly.ToconnectuseSGL#9488
FusedPlugOnly!

LesPuckspeuventêtrereliésausystèmeSGL
LXalimentéparunealimentationélectriqueSGL
HomologuéeClasse1etClasse2uniquement.
Pourrelier,utiliserunePriseFusibleSGLn°9488
uniquement!

EldiscopuedeserconectadoalsistemaSGLLX
impulsadosolamenteconfuentesdeenergíaSGL
conClasicaciónNivel1yNivel2.Paraconectar
utilicesolamenteEnchufeFundidoSGL#9488!
Plug-in,12V30/wZeroLoadElectronicTransformer
TransformateurElectroniqueZéroChargeEnchable12V30/w
Enchufe,TransformadorElectrónicodeCeroCarga12V30/w
• 98640S-12blacknish
Fininoir/Terminadonegro
• 98640S-15whitenish
Finiblanc/Terminadoblanco
LEDpuckconnectionhub
PlotconnexionLEDPuck/
ConcentradordeconexióndelDiscoLED
• 98641S-12blacknish
Fininoir/Terminadonegro
• 98641S-15
Finiblanc/Terminadoblanco
ConnectorCords
CordonsConnecteur/CablesConectores
• 98643S-156"WhiteFinish
6"Finiblanc/6"whitenish
• 98645S-1518"WhiteFinish
18"Finiblanc/18"whitenish
FusedPlug
PriseFusible/EnchufeFundido
• 9488-12
• 9488-15
LEDPuckLightAccessories
LumièrespaletdeLEDaccessoires
LucesLEDdePuckaccesorios
HC-1887FS020812