Manual

ManualsBrandsLBL Lighting ManualsLightingMademoiselle S

Installation Instructions for

Mademoiselle Suspension (LED)

1.0

980MADEMS

CAUTION - RISK OF FIRE

This product requires installation by a qualified

electrician. Before installing be sure to read all

instructions and TURN THE POWERTO THE

ELECTRICAL BOX OFF.

Suspension

SU697_LED

GP I :ENERAL RODUCT NFORMATION

This product is suitable for damp locations.

This product may be dimmed with a low-voltage electronic dimmer.

Shorten the Power Cord

Take note of the wire connections and remove the wire nuts

to disconnect the power cord wires from the driver wires.

POWER CORD

SET SCREW

Loosen the set screw on the strain relief.(Do Not Remove)

Remove the crossbar from the canopy by completely

unscrewing the strain relief.

STRAIN RELIEF

CROSSBAR

CANOPY

SET SCREW

STRAIN RELIEF

CROSSBAR

CANOPY

AIRCRAFT

CABLE

Feed the aircraft cable through the cable clutch in the canopy.

Pull the aircraft cable up through the canopy to determine the

fixture height.

Cut off the excess aircraft cable leaving enough for fine leveling

later.

Pull the power cord through the canopy to the desired length.

CABLE

CLUTCH

STRAIN RELIEF

POWER CORD

CANOPY

Summary of content (8 pages)

PAGE 1
Installation Instructions for 980MADEMS Mademoiselle Suspension (LED) SU697_LED 1.0 Suspension GENERAL PRODUCT INFORMATION: This product is suitable for damp locations. This product may be dimmed with a low-voltage electronic dimmer. CAUTION - RISK OF FIRE This product requires installation by a qualified electrician. Before installing be sure to read all instructions and TURN THE POWER TO THE ELECTRICAL BOX OFF.
PAGE 2
Mount the Fixture 1D 2A 9 #8-32 SCREW CROSSBAR 1 1 CORD 1 Mount the crossbar assembly to the electrical box with the two provided #8-32 screws. NOTE: The power cord does not support the fixture. 2B For a casual “lazy cord” look, cut the power cord several inches longer that the drop height of the fixture. 8 2 9 2 Once the desired look is determined, tighten the set screw on the strain relief. 3 Mark the cord underneath the strain relief.
PAGE 3
B 2C SET SCREW 2 STRAIN RELIEF ANCHOR CORD CEILING 6 Place all wires and wire nut connections properly inside the electrical box. 7 Loosen the set screw on the primary strain relief. 8 Align the canopy center hole with the crossbar center hole. 9 Slide the canopy up against the ceiling and secure it in place by tightening the primary strain relief into the crossbar. Do not turn the cord.
PAGE 4
Install the Crystals 3E 4A S 5 THREADED NIPPLE M CABLE POST L 6 pcs. 15 pcs. THIN STRIP 4 pcs. 2 pcs. 1 5 Note: The following steps to install the mesh is simply a placement diagram. The installer should ensure that the rectangular mesh is an equal length on each side and slightly rotated when draping over the fixture to create an angular look. Taking the time to notice the aesthetics of the placement of each piece will produce the best results.
PAGE 5
4B AIRCRAFT CABLE S STRAIN RELIEF S S M 2 Place 4 small pieces on the outside of each aircraft cable as shown. 3 Place a medium piece next to the aircraft cable away from the power cord as shown. 4 Place a small piece next to the strain relief as shown. S 4C AIRCRAFT CABLE 1” 4.5” S M L STRAIN RELIEF 5 Place a large piece 4.5” away from the inside of the aircraft cable away from the power cord. 6 Place a medium piece 1” away from the inside of the strain relief as shown.
PAGE 6
4E AIRCRAFT CABLE AIRCRAFT CABLE POWER CORD 2.5” 3.5” 12” M S M M 8 Place a medium piece 12” away from the inside of the aircraft cable away from the power cord. 9 Place a medium piece 2.5” away from the outside of the aircraft cable away from the power cord. 10 Place a medium piece 3.5” away from the outside of the aircraft cable next to the power cord.
PAGE 7
4H AIRCRAFT CABLE AIRCRAFT CABLE S S SS S S STRAIN RELIEF 17 Place 2 medium pieces on the outside of each aircraft cable as shown. 18 Place a small piece next to the strain relief as shown. 4I STRAIN RELIEF AIRCRAFT CABLE S THIN STRIP 19 Place 2 thin strips between the strain relief and nearby aircraft cable as shown. Pace them spread out so they cover the void of crystals in this area.
PAGE 8
SAVE THESE INSTRUCTIONS! 7400 Linder Ave, Skokie, IL 60077 800.323.3226 - 847.626.6300 www.lbllighting.com © 2014 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a registered trademark of LBL Lighting. LBL Lighting reserves the right to change specifications for product improvements without notification.