Manual

ManualsBrandsLBL Lighting ManualsLightingMO Rmt Elec Xfmr 150w 120v/12v LED

Installation Instructions for

120 Volt to 12 Volt DC Single Feed 150W Remote

Electronic Transformers

950RM15012EL

GP I :ENERAL RODUCT NFORMATION

This transformer is ETL listed for use with low voltage lighting

systems of brands offered by Encompass Lighting Group.

This product is suitable only for indoor dry locations and

approved for use at any height above the finished floor.

A typical installation is shown. Specific installation must be in

accordance with the local electrical codes.

This product may be dimmed only with a low voltage

electronic dimmer. Using a dimmer not designed for low

voltage electronic applications may work initially, but could

eventually cause transformer failure and will void the warranty.

The dimmer must be derated as indicated by the dimmer

manufacturer.

This product is intended for use with Encompass Lighting

Group brands of low voltage lighting systems only.

During installation, make sure all power connections are tight.

Read all instructions thoroughly. Read "Important Safety

Information" on next column before proceeding with the

installation.

Important Safety Information

Do not conceal or extend bus bar conductors through a

building wall.

Do not install this lighting system in a damp or wet location.

To reduce the risk of fire and burns, do not install this lighting

system where the uninsulated open bus bar conductors can

be shorted or contact any conductive materials.

To reduce the risk of the system overheating and possibly

causing a fire, make sure all the connections are tight.

Do not install fixture assemblies closer than six inches to

curtains or similarly combustible materials.

Turn the electrical power off before modifying the lighting

system in any way.

The fixtures used with the system must be identified for use

with the corresponding system.

Minimum volume of the electrical box must be 6 cubic inches

(98 cubic centimeters).

To Reduce Risk of Fire, it is important to wire the remote

transformer for the system as described in this installation

instruction.

Load the circuit of the remote transformer to 150MAXIMUM

Watt.

TRANSFORMERS

CAUTION: RISK OF FIRE

This product requires installation by qualified

electrician. Before installing be sure to read all

instructions and TURN THE POWER TO THE

ELECTRICAL BOX OFF.

1.0

1.2

Summary of content (4 pages)

PAGE 1
950RM15012EL Installation Instructions for 120 Volt to 12 Volt DC Single Feed 150W Remote Electronic Transformers 1.0 1.2 TRANSFORMERS CAUTION: RISK OF FIRE This product requires installation by qualified electrician. Before installing be sure to read all instructions and TURN THE POWER TO THE ELECTRICAL BOX OFF. Important Safety Information GENERAL PRODUCT INFORMATION: Do not conceal or extend bus bar conductors through a building wall.
PAGE 2
Install the Remote Transformer 1A 1A 1A 1B 1 1 7 3 6 4 2 2 CONDUIT TRANSFORMER COVER PHILLIPS SCREW 1 1 1 NOTE: In order to use small gage wires from the 2 transformer to the electrical box, it is recommended to install the remote transformer near (if possible) the electrical box. See "Low Voltage Wire Size Table" below. Secure the transformer housing in place (hardware not included). 3 Install a conduit and power line wires from the panel to the remote transformer.
PAGE 3
1C 1A 8 Install a conduit from the transformer to the electrical box. 9 For the best performance, use the "Low Voltage Wire Size Table" below to select the wire size. NOTE: Other wire sizes that comply with electrical code can be used, but may result in an increased voltage drop and reduced lamp intensity. NOTE: The THHN wire sizes are for 3% or less drop in voltage based on 150 watt loads. Lengths are the distance from the transformer to the system power feed connector.
PAGE 4
1D 1A 12 Connect the 120 volt power line wires at the panel. 14 14 13 After installing the entire system, operate the system for five minutes. On the low voltage side, all electrical connection points should be no more than warm to the touch. If a connection is hot to the touch, retighten the connection and check to ensure that the temperature decreases. 14 Replace the transformer cover and tighten the four Phillips screws.