Users Manual

19
20
[Door2 status]: Enable or disable the preview of Door2.
[Door1 unlock Time]: From 02 seconds to 10 seconds.
[Door2 unlock time]: From 02 seconds to 10 seconds.
[Video mode]:
Option “On” the mean is turn on the prompt tone when operation
each step. Option”Off” the mean is turn off the prompt tone when operation each step.
[Key backlight]: Option “On” indicates that all key lights on the front panel will be on.
Option “Off” indicates that all key lights on the front panel will be off.
[Door panel backlight]: This option is for outdoor bell with backlight control. Option
“On” indicates that backlight LEDs of the outdoor bell will be on. “Off” indicates that
backlight LEDs of the outdoor bell will be off.
[Return]: Exit the current menu.
From this field, select the video input mode that is consistent with cameras input,
i.e AHD-1080P, or AHD-720P or CVBS. “AHD-1080P” means that user can connect up to four
1080P cameras to the indoor monitor. “AHD-720P” means that user can connect up to two 720P
outdoor doorbells and two 720P CCTV cameras to the indoor monitor. “CVBS" means that user can
connect up to 4 CVBS cameras(2 outdoor bells and 2 cameras) to the monitor.
[Standard]: From this field, select the system output type that is consistent with camera input, i.e.
PAL or NTSC.
[keyboard sound]:
On main menu, move the cursor to “Alarm” and press “ ” to enter the “Alarm” menu to
set up the alarm type of camera 1 or camera 2.
On main menu, Move the cursor to “mode” and press “ ” to enter the “Mode” menu.
[CAM 1 Sensor type or CAM 2 Sensor type]:
CAM1] : Enable or disable the preview of camera 1.
[CAM2]: Enable or disable the preview of camera 2.
[CAM 1 ring time]: The alarm ring time of camera 1, if camera 1 has been triggered by
activity detected by the sensor, values can be set from 0~30
seconds.
[CAM 2 ring time]: The alarm ring time of camera 2, if camera 2 has been triggered by
activity detected by the sensor, values can be set from 0~30
seconds.
[Return]: Exit the current menu.
Each camera channel corresponds to
an I/O status (see the following status explanations), which means that when an alarm
is triggered, it will activate the indoor monitor to issue an alert, the duration of the alert
will be according to “CAM1 ring time” or “CAM2 ring time”.
I/O status types:
NO: “Normally open”, it means that in its normal state, the sensor is kept under
constant low voltage. If the output voltage changes from low to high, then the
alarm will be triggered.
NC: “Normally closed”, the normal state of the sensor is under constant high voltage.
If the output voltage changes from high to low, then the alarm will be triggered.
Off: Set the sensor type to “Off”, it means external sensor alarms are not in use.
[
2.3 Set the mode of the indoor monitor
2.4 Alarm
Return
CAM1 sensor type: NO
CAM2 sensor type: NO
CAM1: On
CAM2: On
CAM1 ring time: 20 sec
CAM2 ring time: 20 sec
Door2 status: On
Door1 unlock time: 03 sec
Door2 unlock time: 03 sec
Video mode: CVBS
Standard: PAL
Keyboard sound: On
Key backlight: On
Door panel backlight: On
Return
On the color menu the video color of Door1/Door2/CAM1/CAM2 attributes can be
adjusted for the best image quality. Choose on the option “Door1” or “Door2” or “CAM1”
or “CAM2” to enter the corresponding menu to adjust values of brightness, contrast and
saturation depending on the actual conditions. Scroll the button “ ” upward or
downward to adjust values.
[Brightness]: values can be set up from 0 to 50.
[Contrast]: values can be set up from 0 to 50.
[Saturation]: values can be set up from 0 to 50.
[Return]: Exit the current menu.
2.5 Set the color parameters
25
25
35
Return
Door1
Door1 Door2
CAM1 CAM2
Return
On main menu, move the cursor to “Color” and press “ ” to enter the “color” menu.