Users Manual

14
13
2. Menu Operations On Indoor Monitor
2.1 Mouse Control
Internal communication function requires at least two indoor and one outdoor units to be connected.
Outdoor camera call indoor
monitor and conversation
is underway
Press the “ ” button
to activate
call transfer to other
extension.
the function of
A continuous ring
tone is heard
NOTICE:
When you are transferring a call to other extension, the original
conversation indoor unit will return to standby mode, and the
indoor unit which the call is being transferred will also sound a
continuous ring tone and the video image will appear on its
screen.
Press the talk
button on any of
indoor units
Talking
with visitor
At least 2 indoor units is required.
Standby Mode
Press the “ ”
button
Press the talk
button on any of
indoor units
Start conversation
among indoor units
.
Press Hang
up button
End
NOTICE：
In internal communication mode, if a visitor press the call
button on either of outdoor unit, the internal communication
mode will be switched off. The just visitor' s image will appear
on its screen and continuous ringing will be heard, you can
press the talk button to reactivate conversation with the
visitor.
The Electric
lock can
be opened
End the call
and return to
standby mode.
Call Transfer To Other Extension
Internal Communication Among Indoor monitors
A continuous ring tone
is heard
TF
In standby mode, press the button “ ” to access the main menu interface, shows the main
as shown below. On menus, scroll “ ” upward or downward to move the cursor to the option “Return”,
then press “ ” to exit; or press “Hang up” to return.
interface
The button “ ” is a three-in-one key, but also composite keys:
In standby mode, press the button “ ” once to enter the main menu settings. In main
scroll the button “ ” upward or downward to select sub-menu, then press “ ” again to enter
sub-menu. In sub-menu settings, press “ ” to select menu options, scroll “ ” upward or downward
to adjust values of each option, then press “ ” to confirm. When select option “Return” on main menu,
press the button “ ” to exit menu interface, or press “Hang up” button, the indoor monitor will be
into standby mode.
menu settings,
Hang up
Hang up
System Ring Mode
Alarm Color
Return
Attention before using:
1. This indoor monitor includes OSD menu on it’s own device, users could set up some
parameters on the indoor monitor.
2. User can connect the device through web browser on PC, please refer to section
“3. Web Browser Operation”.
3. Also user can connect the indoor monitor through mobile phone/tablet with the
“uCareHome” app, please refer to “uCareHome app for IP Indoor Monitor User Manual”.
4. The motion detection function only supports for one channel, it means that when
activating motion detection function of the Door 1, the motion detection function of the
other channel can’t be activated at the same time. User can set up the motion detection
parameters through IE browser or the “uCareHome” app.
5. The TF card can be formatted remotely via the “uCareHome” app or through IE browser,
the file system of the TF card must be FAT32.
6. The TF card will be used to store video record or snapshot when calling on the outdoor
bell, please refer to the configuration on section “5.3.6 Event-Record”.
7. When all the button LEDs is flashing, the indoor monitor is ready in AP mode.
8. When unlocking, the app unlock time is set separately from the monitor’s own unlock
time. If unlock from the app “uCareHome”, the unlock time of Door1 and Door2 are the
same, will be consistent with the menu option value “Device Information->Unlock Time”.
If unlocking on the monitor, the unlock time of Door1 and Door2 can be different, will be
consistent with the menu option value “Mode->Door1 unlock time/Door2 unlock time”.
9. If users don’t do any operate or enter any interface about the indoor monitor, the indoor
monitor will be into standby mode after 1 minute automatically.
10. When the menu option “Key backlight” is set to “ON”, when user presses any button or
some visitor calls on the outdoor doorbell, all back-light LEDs of the button will be on. If
the indoor monitor is in standby mode, if user doesn’t do any operate on the device in 10
seconds, the back-light of each button will be off.
11. During editing parameters on the monitor, the red characters indicate that the option
has been selected. When the red characters flash, it indicates that the option is in edit state.