User Manual

ManualsBrandsLDARC / KINGKONG ManualsAircraftsTINY WING 450X V2 (White Orange Black)

LDARC 450X V2

112mm

Roll and Pitch Center of gravity

Tools:Screwdriver, foam glue, art knife and other tools

User manual and video please visit：WWW.LDARC.COM

Departments 》 FPV FLY Wing 》 LDARC 450X V2

-1-

Note: Be sure to open the transmitter first, then power on the plane; and be sure to the

transmitter has been set up fail safe

Operate Step: Open TX > > > >Power on airplane ESC & FC self test ARM Flying

Wingspan : 431mm

Length : 277mm

Material : EPP

Prop : 3.8*3E

Battery : 7.4V 450mAh

Voltage : Only 2S

FC : FC01

ESC : 6A BLheli

Servo : WK-P0025(2.5g)*2

Motor : XT1105*5000KV

VTX : 200mW 48CH(FPV version)

Camera : RunCam micro swift 3(FPV version)

Transmitter : LDARC X6(RTF version)

Wing weight(no receiver & battery) :

PNP : 70g

FPV : 91g

RTF : 70g

Package weight :

PNP: 600g

FPV : 610g

RTF : 1150g

Package size :

PNP : 470*290*60mm

FPV : 470*290*60mm

RTF : 470*290*150mm

Configuration : □ PNP □ FPV □ RTF

200709

Summary of content (8 pages)

PAGE 1
200709 User manual and video please visit：WWW.LDARC.COM LDARC 450X V2 Configuration : □ PNP □ FPV Departments 》 FPV FLY Wing 》 LDARC 450X V2 □ RTF Wingspan : 431mm Length : 277mm Material : EPP Prop : 3.8*3E Battery : 7.4V 450mAh Voltage : Only 2S FC : FC01 ESC : 6A BLheli Servo : WK-P0025(2.
PAGE 2
Pre-flight check: Please switch to manual mode after the self-test is complete on the aircraft, at which point the left and right ailerons must be on the same horizontal surface as the wing root; if not inconsistent, it can be adjusted by the length of the steel rod. FC ESC S GND 2S Input(Battery) + Mode & Self test LED 30mm Pneumatic gauge GND LED 4.2V+ S 41mm S 4.2V+ LED GND S Servo port 4.2V+ 1.25-3P GND 37mm GND Servo port 4.2V+ 1.25-3P S 26mm + - S.bus 4.
PAGE 3
2.Mix level(LED is green flashing,you can flip it 360 degrees; air pressure set high, current height hold) 3.Manual(LED is blue light,handfree operation,FC without any intervention) Transmitter setting: 1.Create a new standard fixed-wing model(AIRPLANE),wing type(1AIL),tail type(NORMAL). 2.Channel sort definition: ① AIL; ② ELE; ③ THR; ④ RUD; ⑤ AUX(ARM/Dis-ARM); ⑥ MOD(Flight mode). FC function: 1.
PAGE 4
RTF version 450X radio instructions : FLIGHT MODE INDICATOR RADIO BATTERY INDICATOR DIS-ARM/ARM BUTTON Flight mode indicator FLIGHT MODE SWITCH BUTTON 450X DIS-ARM, the LED on 450X wings will ■always on on radio ■always on Click the 【DIS-ARM/ARM BUTTON】on radio will ARM 450X 450X ARM, the LED on 450X wings will ■always on，fight mode 【SELF LEVEL】, altitude hold enable Flight mode indicator on radio ■always on Click the 【DIS-ARM/ARM BUTTON】on radio will DIS-ARM 450X Click the 【FLIGHT MODE SWITCH BUTT
PAGE 5
KIT Configuration Lists KIT Include 2PCS KIT *2PCS Part 1 *2PCS *4PCS Stiker*2PCS Part 3 Part 2 *4PCS *4PCS Prop*10PCS orange,white,clear *2PCS Part 4 *2PCS *2PCS *2PCS *2PCS *4PCS Orange & Black *2PCS *8PCS Part 5 *4PCS *2pairs *4PCS *16PCS ST2.0*6*4PCS ST1.5*5*16PCS Heat shields*2pairs M2*5*8PCS *2PCS *2PCS *4PCS Part6 *1PC Heat shields*2pairs *1PC M2*5*4PCS ST1.
PAGE 6
PNP PNP*1PC *1PC M2*5*4PCS *2PCS *1PC Prop*10PCS (orange,white,clear) *2PCS M2*8*8PCS *2PCS Battery*1PC *1PC Sticker*1PCS Heat shields*2Pairs ST1.2*4*8PCS FPV FPV*1PC *2PCS Prop*10PCS (orange,white,clear) M2*8*8PCS Battery*1PC Sticker*1PCS *2PCS Prop*10PCS (orange,white,clear) M2*8*8PCS Battery*1PC TX*1PC *1PC RTF PNP*1PC *1PC M2*5*4PCS *1PC ST1.
PAGE 7
FPV install step: 1.Weld OK the FC and VTX connect wire 2.Use M2*3.5 screw install camera, and use gule stick the canopy & magnet together. 3.Connet VTX antenna,stick EVA,and fixed the antenna well. 4.Install VTX,then connect together with FC & camera. Install steps: 1.Weld the motor, ESC, FC and power cable together , recommend that the power cable and signal cable cut to 30mm.
PAGE 8
2.Use foam glue to stick EPP, plastic parts, magnets, reinforced bars well 3.Use ST1.5*5 screw install LED, servo, rudder angle, steel wire rod and lampshade. A 4.Use ST1.5*5 screw install FC,ST2.0*6 screw install motor set,then stick the EPP well.