WUS MOTO Gen3 HD Mounting process Distribution: Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent Internal Status: Confidential Ref : C 317 109 0000 Version : A1 External Restricted ✘ Extended ✘ TITLE: WUS MOTO Gen3 HD Mounting process Reference : C 317 109 0000 Version A1 Internal Approval Name and Department Date Author Check Approver L.LAFRANCHIS (MD) D.LUCE (MD) P.
Ref : C WUS MOTO Gen3 HD Mounting process 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent VERSIONS HISTORY Version Update Date Chapters / Pages modified Modification origin Author Comments A0 A1 04/02/19 28/08/19 All Chapter 9 Creation Added L.LAFRANCHIS P. GABAUDAN Initial version C317-109-0000-A1-WUS Gen3 HD Mounting Specification.
WUS MOTO Gen3 HD Mounting process Ref : C 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent Table des matières 1.PURPOSE................................................................................................................................... 4 2.TERMINOLOGY, ACRONYMS AND ABBREVATIONS.............................................................4 2.1.Terminology.....................................................
WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 1. Ref : C 317 109 0000 Version : A1 PURPOSE This document describes the requirements for the mounting of WUS. 2. App NA NR TBD TBC HW Q SW RF WUS PL WL MD TERMINOLOGY, ACRONYMS AND ABBREVATIONS 2.1. TERMINOLOGY 2.2.
WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 3. Ref : C 317 109 0000 Version : A1 DESCRIPTION The wheel unit sensor (WUS) is a pressure and temperature sensor composed with: • A molded black plastic housing, • A metal Screw M5 with Torx T15 head, with a captive washer. • An anodized aluminum valve oriented at 90°; including an EPDM seal and a short core mechanism. 4.
Ref : C WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 4.1. 317 109 0000 Version : A1 SPECIFICATIONS Screwing torque for valve core mechanism: 0.3 +/- 0.1 Nm. Screwing torque for valve cap: 0.2 to 0.35 Nm. Manual screwing torque for T15 Screw: 2,1Nm +/- 0.1 Nm. Operating Relative Pressure Range: 0 to 3,5 bars.
WUS MOTO Gen3 HD Mounting process Ref : C 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent ¨ The valve cap must always be in place (except for inflating, pressure release or pressure checks). 5.2. WUS MOUNTING ¨ Check the external surface of the rim cleanness ; remove grits and other paint marks ¨ Orientation of the Wheel Unit Sensor on the rim: the WUS Case laser marked must be visible after mounting.
Ref : C WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 5.3. 317 109 0000 Version : A1 WUS SCREWING RECOMMENDATIONS Make sure the following recommendations are respected : Screwing speed : max of 2 turns in 1 second. ¨ Apply a torque of 2,1 Nm +/- 0,1 Nm with the good screwing speed. ¨ For the manual process please use a torque controlled tool.
Ref : C WUS MOTO Gen3 HD Mounting process 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent Electronic part. This part is situated inside the wheel RIM Valve including the seal ; is situated on the external part of the wheel 5.4. DETAILED VIEWS OF WUS ASSEMBLY Step N° 1 The plastic round shape shall go inside the valve hole Step N°2 The valve seal must face the rim valve hole on the external side.
Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent WUS MOTO Gen3 HD Mounting process Step N°3 Ref : C 317 109 0000 Version : A1 Maintain the WUS Case and push on the valve (schema page 7). Step N°4 - Torque the T15 Srew with a torque screwdriver (T15). Do note exceed 2 rounds per second. - Final torque 2,1 Nm +/- 0,1 Nm.
Ref : C Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent WUS MOTO Gen3 HD Mounting process 317 109 0000 Version : A1 - Check that the external part of the valve does not meet any obstacle during rim rotation (like break system). Step N°6 - Check that the external seal is correctly set and that the valve is in contact with the rim. 5.5.
Ref : C WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 6. 317 109 0000 Version : A1 TIRE MOUNTING 6.1. PRECAUTIONS ¨ Before any mounting operation of the tire, make sure that the Wheel Unit Sensor has been correctly mounted and tightened to the rim. ¨ The tire must be lubricated so as to facilitate its mounting. Respect manufacturer recommendations.
WUS MOTO Gen3 HD Mounting process Ref : C 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent For manual mounting only – standard dealer shop machine For clockwise tire mounting machine First sidewall : Step N°1 Start putting the tire on the rim on the opposite side of the valve WUS Step N°2 The first sidewall is now introduced C317-109-0000-A1-WUS Gen3 HD Mounting Specification.
WUS MOTO Gen3 HD Mounting process Ref : C 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent Second sidewall : Step N°3 30° to 80° Start introducing manually the second sidewall At almost 50° far away the valve Step N°4 At the end of the mounting process, the second sidewall end climbing on the rim when the shoe is in front of the valve C317-109-0000-A1-WUS Gen3 HD Mounting Specification.
Ref : C WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 7. 317 109 0000 Version : A1 DISMOUNTING A TIRE EQUIPPED WITH A WUS ¨ Before detaching the tire, make sure that the Wheel Unit Sensor is still correctly mounted and tightened on the rim, by checking that the valve is tightened.
WUS MOTO Gen3 HD Mounting process Ref : C 317 109 0000 Version : A1 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent Scheme: Universal tire mounting and dismounting procedure Valve dans la position de départ. Valve START position. Outil de montage (immobile). Mounting tool (static). Environ 50°. About 50°. Pneu. Tire. Jante. Rim. Sens de rotation de la roue sur l’appareil Wheel spin direction on the Mounting machine.
Ref : C WUS MOTO Gen3 HD Mounting process Version : A1 Step N°4 Step N°3 Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 317 109 0000 Slide the tool head under the tire Then make the tire turn to disengage the first sidewall Disassembly of the second sidewall.
WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 8. Ref : C 317 109 0000 Version : A1 WUS DISMOUNTING It is MANDATORY to interchange the seal if a complete disassembly of the WUS is done (if you change the rim for example), all unscrewing action on the T15 Screw is equivalent to a complete disassembly. 8.1.
WUS MOTO Gen3 HD Mounting process Document is the property of LDL-Technology and cannot be reproduced or transmitted without written consent 9. Ref : C 317 109 0000 Version : A1 REGULATIONS FCC: “Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment”. “This device complies with Part 15 of the FCC rules.
