User's Manual

ManualsBrandsLear ManualsElectronicsRemote Control Transmitter

Lear UGDO

Lear UGDO Owner’s Guide Version 3.2 Page 1 3/27/2006

Lear Car2U Transmitter

The Lear Universal Garage Door Opener (LEAR Car2U ™) is a universal transmitter and can

replace up to three different remote control transmitter units used to operate the following types

of devices:

x Garage Door Opener

x Security Devices

x Home Lighting Systems

Additional Lear Car2U ™ information can be found on the internet at www.learcar2U.com or by

calling 1-866-57Car2U.

Types of Garage Door Openers (Fixed Code and Rolling Code)

Lear UGDO™ has the capability of programming rolling code and fixed code garage door

openers:

x Rolling code garage door openers are used for garage doors produced after 1996 and are

code protected. Rolling code means the coded signal is changed every time your remote

control garage door opener is used.

x Fixed code garage door openers are used for garage doors produced prior to 1996. Fixed

code uses the same coded signal every time, which is manually programmed by setting

DIP switches for a unique personal code.

If you do not know if your garage door opener is a rolling code or fixed code device, open your

garage door opener’s remote control battery cover. If a panel of DIP switches is present as

shown in the typical remote device shown below, your garage door opener is a fixed code device.

If not, your garage door opener is a rolling code device.

Summary of content (8 pages)

PAGE 1
Lear UGDO Lear Car2U Transmitter The Lear Universal Garage Door Opener (LEAR Car2U ™) is a universal transmitter and can replace up to three different remote control transmitter units used to operate the following types of devices: x x x Garage Door Opener Security Devices Home Lighting Systems Additional Lear Car2U ™ information can be found on the internet at www.learcar2U.com or by calling 1-866-57Car2U.
PAGE 2
Lear UGDO Programming the Lear UGDO™ Transmitter Depending on your garage door opener manufacturer, Lear UGDO™ provides two easy ways to program your garage door opener. 1. Rolling Code Garage Door Openers: If your garage door opener is a rolling code device and do not have a row of dip switches use the “Programming Rolling Code Garage Door Opener” procedure on page 4. 2.
PAGE 3
Lear UGDO CAUTION Programming the Rolling Code Garage Door Opener involves time-sensitive actions. Read the ENTIRE procedure prior to beginning so you will know which actions are time-sensitive. If you do not follow the time-sensitive actions, the device will time out and you will have to repeat the procedure. Make sure that your key is ON and engine OFF while programming the transmitter. Use the following steps to program up to three different devices. Lear UGDO Owner’s Guide Version 3.
PAGE 4
Lear UGDO Programming Rolling Code Garage Door Opener or Device 1. Firmly PRESS the outer two Lear UGDO™ buttons for immediately release them. one — two seconds and 2. Go to the garage. Locate the garage door motor head and Press and Release its “learn” button. You may need a ladder to reach the unit and you may need to remove the unit’s cover to locate the “learn” button.
PAGE 5
Lear UGDO 4. The indicator light will blink rapidly until programming is complete Press and release the button again. The garage door should move confirming that programming is successful and complete. 5. To program another rolling code device such as an additional garage door opener, a security device, or home lighting, repeat steps 1 – 4 substituting a different function button in Step 3 than what you used for the garage door opener.
PAGE 6
Lear UGDO Programming Fixed Code Garage Door Opener or Device Make sure that your key is ON and engine OFF while programming the transmitter. Use the following steps to program up to three different devices. 1. To program a fixed code garage door opener you will need the garage door hand-held transmitter and a paper and pen or pencil. Between 8 and 12 coding switches are revealed under the battery cover of the hand-held transmitter. Do not change the switch positions. 2.
PAGE 7
Lear UGDO 5. After inputting the switch settings, simultaneously Press and Release all 3 Car2U buttons. The indicator lights will turn on. 6. Press and HOLD the Car2U Button you would like to use to control the garage door. The indicator light above the selected button should slowly blink. You may need to hold the button from 5 to 55 seconds. Press ANY one of the three Lear UGDO™ buttons to assign the fixed code sequence to the garage door opener. 7.
PAGE 8
Lear UGDO Erasing Lear UGDO™ Buttons Note The system allows for three devices to be programmed. If you need to change or replace any of the three devices after it has been initially programmed, it will be necessary to erase the current settings using the “Erasing Lear UDGO™ Buttons” procedure and then reprogram ALL of the devices being used. In order to erase either rolling code or fixed code on the LEAR UGDO™ device, use the following procedure: 1.