INSTRUCTION MANUAL SMWB/E07-941 Wireless Microphone Transmitters and Recorders SMWB/E07-941 SMDWB/E07-941 Featuring Digital Hybrid Wireless® Technology US Patent 7,225,135 Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.
SMWB/E07-941 Series Table of Contents Introduction.............................................................................................................................................................................................4 About Digital Hybrid Wireless® ...............................................................................................................................................................................................................................................
Digital Hybrid Wireless Belt-Pack Transmitters ISEDC Notices: This device operates on a no-protection no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. Please consult Industry Canada’s document CPC-2-1-28, Optional Licensing for Low-Power Radio Apparatus in the TV Bands, for details. Ce dispositif fonctionne selon un régime de non-brouillage et de non-protection.
SMWB/E07-941 Series Introduction The design of the SMWB/E07 transmitter delivers the advanced technology and features of Digital Hybrid Wireless® in a Lectrosonics belt-pack transmitter at a modest cost. Digital Hybrid Wireless® combines a 24-bit digital audio chain with an analog FM radio link to eliminate a compandor and its artifacts, yet preserve the extended operating range and noise rejection of the finest analog wireless systems.
Digital Hybrid Wireless Belt-Pack Transmitters Features Modulation Indicators REC Battery Status LED -40 -20 0 microSDHC memory card port microSDHC memory card port Antenna Port Audio Input Jack IR (Infrared) Port Battery Status LED Indicator AA batteries can be used to power the transmitter. The LED labeled BATT on the keypad glows green when the batteries are good. The color changes to red when the battery voltage drops down and stays red through most of the battery life.
SMWB/E07-941 Series Battery Installation The transmitter is powered by two AA batteries. Because rechargeable batteries run down quite abruptly, using the Power LED to verify battery status will not be reliable. However, it is possible to track battery status using the battery timer function available in Lectrosonics Digital Hybrid Wireless receivers. The battery door opens by simply unscrewing the knurled knob part way until the door will rotate.
Digital Hybrid Wireless Belt-Pack Transmitters Transmitter Operating Instructions Recorder Operating Instructions • Install battery(s) • Install battery(s) • Turn power on in the Standby mode (see previous section) • Insert microSDHC memory card • Connect microphone and place it in the position where it will be used. • Format memory card • Have user talk or sing at the same level that will be used in the production, and adjust the input gain so that the -20 LED blinks red on louder peaks.
SMWB/E07-941 Series SMWB Main Menu From the Main Window press MENU/SEL. Use the UP/Down arrow keys to select the item. Files Files Format? SEL (erases) BACK Record SEL BACK Gain SEL Freq. SEL Gain Use arrow keys to initiate formatting the memory card No Yes RECORDING OR Stop SEL BACK SAVED Use arrow keys to select input gain Select from listing 22 BACK b 21 80 550.
Digital Hybrid Wireless Belt-Pack Transmitters SMWB Power Button Menu From the Main Window press the power button. Use the UP/DOWN arrow keys to select the item. Resume Press SEL to return to the previous screen Pwr Off Press SEL to turn the power off Rf On? SEL BACK No Yes Use arrow keys to turn RF signal on/off AutoOn? ProgSw SEL BACK No Yes Use arrow keys to enable auto power restore Remote Remote SEL BACK Enable Ignore BatType BatType SEL BACK 1.5 V Alk. Lith.
SMWB/E07-941 Series Setup Screen Details Locking/Unlocking Changes to Settings Changes to the settings can be locked in the Power Button Menu. Clock Locked LED Off About Locked? LOCKED No Yes (menu to unlock) When changes are locked, several controls and actions can still be used: • Settings can still be unlocked • Power can still be turned off by using the power menu or removing the batteries.
Digital Hybrid Wireless Belt-Pack Transmitters Format Files For mat Record Gain Formats the microSDHC memory card. WARNING: This function erases any content on the microSDHC memory card. Selecting Frequency The setup screen for frequency selection offers several ways to browse the available frequencies. Record or Stop Begins recording or stops recording. (See page 7.
SMWB/E07-941 Series Selecting Frequency Using Two Buttons Hold the MENU/SEL button in, then use the arrow buttons for alternate increments. 100 kHz Mode Freq. b 19 10 MHz steps and 1 block steps 1.6 MHz steps to nearest 100 kHz channel 51 494.500 100 kHz steps to next 100 kHz channel 10 MHz steps 1 block steps 1.6 MHz steps 51 41 494.
Digital Hybrid Wireless Belt-Pack Transmitters Selecting Step Size Choosing Takes for Replay This menu item allows frequencies to be selected in either 100 kHz or 25 kHz increments. Rolloff Compat StepSiz Phase StepSiz StepSiz 100 kHz 25 kHz 100 kHz 25 kHz If the desired frequency ends in .025, .050 or .075 MHz, the 25 kHz step size must be selected. Normally, the receiver is used to find a clear operating frequency.
SMWB/E07-941 Series 5-Pin Input Jack Wiring The wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some microphones may require extra jumpers or a slight variation on the diagrams shown. Audio input jack wiring: PIN 1 Shield (ground) for positive biased electret lavaliere microphones. Shield (ground) for dynamic microphones and line level inputs.
Digital Hybrid Wireless Belt-Pack Transmitters Microphone Cable Termination for Non-Lectrosonics Microphones TA5F Connector Assembly Mic Cord Stripping Instructions 1 4 5 2 3 VIEW FROM SOLDER SIDE OF PINS 0.15" 0.3" Crimping to Shield and Insulation Strip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness.
SMWB/E07-941 Series Input Jack Wiring for Different Sources In addition to the microphone and line level wiring illustrated below, Lectrosonics makes a number of cables and adapters for other situations such as connecting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog. A lot of information regarding microphone wiring is also available in the FAQ section of the web site at: www.lectrosonics.
Digital Hybrid Wireless Belt-Pack Transmitters Microphone RF Bypassing Line Level Signals When used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with microphone/transmitter compatibility.
SMWB/E07-941 Series Belt Clips and Pouches SMWB Single Battery Model SMDWB Dual Battery Model SMWBBCUP SMDWBBCSL Wire clip for single battery model; antenna points UP when unit is worn on a belt. Wire clip for dual battery model antenna points UP when unit is worn on a belt; can be installed for UP or DOWN antenna. SMWBBCDN Wire clip for single battery model; antenna points DOWN when unit is worn on a belt. SMDWBBCSL Spring-loaded clip for dual battery model; can be installed for UP or DOWN antenna.
Digital Hybrid Wireless Belt-Pack Transmitters Miscellaneous Accessories SMKITTA5 Mic cable not included TA5 connector kit; with sleeves for small or larger cable; mic cable not included SMSILVER Small vial of silver paste for use on battery door retaining knob threads 55010 MicroSDHC memory card with SD adapter. UHS-I; Class 10; 16 GB. Brand may vary. P/N 35924 FOAM INSULATING PADS Attached to the side of the transmitter when it is worn very close to or on the user’s skin.
SMWB/E07-941 Series LectroRM Android By New Endian LLC LectroRM is a mobile application for iOS and Android operating systems. Its purpose is to remotely control Lectrosonics Transmitters, including: • SM Series • WM • L Series The app remotely changes settings on the transmitter through the use of encoded audio tones, which when received by the attached microphone, will alter the configured setting. The app was released by New Endian, LLC in September 2011.
Digital Hybrid Wireless Belt-Pack Transmitters Silver Paste on SM Series Transmitter Thumbscrews Silver paste is applied to thumbscrew threads on new units at the factory to improve the electrical connection from the battery compartment through the housing on any SM Series transmitter. This applies to the standard battery door and the battery eliminator. Threads provide electrical contact Simply hold the cloth around the threads and turn the thumbscrew. Move to a new spot on the cloth and do it again.
SMWB/E07-941 Series Firmware Update Firmware updates are made using a microSDHC memory card. Download and copy the following firmware update files to a drive on your computer. • smwb_e01 vX_xx.ldr is the firmware update file, where “X_xx” is the revision number. In the computer: 1) Perform a Quick Format of the card. On a Windows-based system, this will automatically format the card to the FAT32 format, which is the Windows standard. On a Mac, you may be given several options.
Digital Hybrid Wireless Belt-Pack Transmitters Recovery Process In the event of a battery failure while the unit is recording, a recovery process is available to restore the recording in proper format. When a new battery is installed and the unit is turned back on, the recorder will detect the missing data and prompt you to run the recovery process. The file must be recovered or the card will not be usable in the SMWB/E07.
SMWB/E07-941 Series Specifications Transmitter Recorder Operating Frequency Range: 941.525 - 951.975 MHz 953.025 - 956.225 MHz 956.475 - 959.825 MHz For FCC Part 74 and ISED RSS-123 licensed users. Channel Spacing: RF Power output: Compatibility Modes: Pilot tone: Frequency stability: Spurious radiation: Equivalent input noise: Input level: If set for dynamic mic: Selectable; 25 or 100 kHz Selectable; 25, 50 or 100 mW Nu Hybrid, IFB 3.5 kHz deviation (Nu Hybrid) ± 0.
Digital Hybrid Wireless Belt-Pack Transmitters Troubleshooting It is important that you follow these steps in the sequence listed. Symptom: Possible Cause: Transmitter Battery LED off when Power Switch “ON” 1. Batteries are inserted incorrectly. 2. Batteries are low or dead. No Transmitter Modulation LEDs when Signal Should be Present 1. 2. 3. 4. 5. 6. Receiver Indicates RF But No Audio 1. Audio source or cable connected to transmitter is defective. Try using an alternate source or cable. 2.
SMWB/E07-941 Series Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop attempt anything other than the simplest repair.
Digital Hybrid Wireless Belt-Pack Transmitters Rio Rancho, NM 27
LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor.