Installation and Operating Instructions

ManualsBrandsLeetron ManualsElectronicsremote control

INSTALLATION AND OPERATING INSTRUCTIONS

Model: FC202-01

FCC ID: 2ATZEFC20201

MULIT-FUNCTION WIRELESS REMOTE CONTROL SYSTEM

FOR OPERATING A LATCHING SOLENOID VALVE, MANUALLY OR WITH A THERMOSTAT FUNCTION

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT

ATTEMPT TO INSTALL OR OPERATE

INTRODUCTION

This remote control system was developed to provide a safe, reliable, and user-friendly remote control

system for gas heating appliances. The system is operated manually from the transmitter. The system

operates on radio frequencies (RF) within a 20' range using non-directional signals. The system

operates on one of 16777216 security codes that are programmed into the transmitter at the factory;

the remote receiver's code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY SECTION under TRANSMITTER section under REMOTE RECEIVER

section. This signal safety feature shuts down the fireplace system when a potentially unsafe condition

exists.

TRANSMITTER FC202-01

This remote control system provides remote control operation for a battery-powered latching solenoid

valve, such as those used with gas valves, for gas heaters, air convection heaters, positive displacement

water heaters, wall-mounted heating Furnaces, commercial gas appliances, and all other gas

appliances that have high requirements for temperature control.

The solenoid circuit uses the battery power from the receiver to operate a solenoid. The circuit has

LCD

BUTTON

OFF

BUTTON

MODE

BUTTON

DOWN

BUTTON

BATTRY

COMPARTMENT

WALL CLIP

SLOT

Summary of content (11 pages)

PAGE 1
INSTALLATION AND OPERATING INSTRUCTIONS Model: FC202-01 FCC ID: 2ATZEFC20201 MULIT-FUNCTION WIRELESS REMOTE CONTROL SYSTEM FOR OPERATING A LATCHING SOLENOID VALVE, MANUALLY OR WITH A THERMOSTAT FUNCTION IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating appliances. The system is operated manually from the transmitter.
PAGE 2
reversing polarity software which reverses the positive (+) and negative) output of the receiver's battery power to drive a latching solenoid ON/OFF. The SYSTEM is controlled by the remote transmitter. The transmitter operates on a (2) 1.5V AAA batteries. It is recommended that ALKALINE batteries always be used for longer battery life and maximum operational performance. Before using the transmitter, install the (2) AAA transmitter batteries into the battery compartment.
PAGE 3
4.A：Thermostat function 5.M：Manual function 6. ：Remote control battery display 7.0F or 0C：Indicates degrees Fahrenheit or Celsius. INSTRUCTIONS When the remote control is loaded with the battery and any button on the remote control is pressed, the full screen lights up. Then the ambient temperature is displayed. The default unit is °F, manual mode, and the battery level is displayed. MANUAL FUNCTION In the manual mode of the operating system, please do the following.
PAGE 4
the display lights up and the “M” icon goes out. Press the “MODE” button again to switch back to the manual mode. The “A” icon on the display is off, and the “M” icon is on and the cycle is switched. TO CHANGE THE SET TEMPERATURE In the automatic constant temperature mode, directly press the “∧” and “∨” keys to adjust the target temperature value (the manual mode cannot be adjusted). When adjusting, the “TEMP” icon is off. After the target temperature is adjusted, do not press any button.
PAGE 5
between SET temperature and ROOM temperature, which determines when the fireplace will be activated. The remote control has the manual function of turning on and off. The "ON" and "OFF" keys must be executed at all times. When the "OFF" is pressed, a signal is sent to the receiver to perform the action of closing the solenoid valve. At the same time, after 10 seconds, the display is turned off.
PAGE 6
responds to commands from the transmitter to control system operation. FUNCTIONS: ●With the slide switch in the OFF position (toward the LEARN button), the system is off. ●With the slide switch in the REMOTE position (centered), the system will only operate if the remote receiver receives commands from the transmitter. ●With the slide switch in the ON position (away from the LEARN button), the system will remain on until the slide switch is placed In the OFF or REMOTE position.
PAGE 7
figure to the down) MPORTANT NOTE: Operation of this control is dependent on which wire is attached to which terminal. If operation of control does not correspond to operating buttons on transmitter, reverse wire installation at the receiver or at the control. NOTE: Up to 6.3 VDC of power is provided at the receiver terminal.
PAGE 8
every 4 seconds until a transmitter ON or MODE Button is pressed to reset the receiver. The intermittent 4-second beeping will go on for as long as the receiver batteries last, which could be in excess of one year. To "reset the RECEIVER and operate the appliance, you must press the ON or MODE button on the transmitter. By turning the system to ON, the COMMUNICATION -SAFETY operation is overridden and the system will return to normal operation depending on the MODE selected at the transmitter.
PAGE 9
or three more times. TRANSMITTER WALL CLIP The transmitter can be hung on a wall using the clip provided. If the clip is installed on a solid wood wall, drill 1/8" pilot holes and install with the screws provided. If It is installed on a plaster/wallboard wall, first drill two 1/4" holes into the wall. Then use a hammer to tap in the two plastic wall anchors flush with the wall; then install the screws provided.
PAGE 10
● Make sure the batteries are correctly installed in the RECEIVER. One reversed battery will keep receiver from operating properly. ● Check battery in TRANSMITTE to make sure contacts are touching (+) and (-) ends of battery. Bend metal contacts in for tighter fit. ● Be sure RECEIVER and TRANSMITTER are within 20’-25’ operating range. ● Keep RECEIVER from temperatures exceeding 130° F. Battery life shortened when ambient temperatures are above 115° F.
PAGE 11
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.