LDCS 91 OWNER'S MANUAL Mobile Video System CAR DVD/VCD/CD/MP3 CASSETTE RECEIVE ST TAPE IN MODE POWER CLK STOP PLAY/PAUSE MUTE ST/MO ANGLE REPEAT TITLE/PBC LO/DX SETUP BAND OSD SEL EQ A/P + 3 IN 1 DVD & CASSETTE & RADIO UP F.FWD NEXT VOL ENTER F.BWD PREV.
CONTENTS Safety Information ........................................................................................2 Disc Notes .....................................................................................................3 Tape Notes.....................................................................................................4 Installation .....................................................................................................5 Electric Connection ...............................
SAFETY INFORMATION CAUTION: THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND - DO NOT REPAIR YOURSELF. REFER SERVICINGTO QUALIFIED PERSONNEL.
DISC NOTES Disc formats supported by this player DVD 12 cm disc (Single-sided disc only) Video CD 12 cm disc CD 12 cm disc MP3 12 cm disc Label side up Do not touch the underside of the disc Discs which cannot be played with this player • DVD-ROM • DVD-R/DVD-RAM • CDV • CD-G Do not bend Wipe the disc from center toward the outside edge Handling and Cleaning • Dirt, dust, scratches and warping disc will cause misoperation. • Do not place stickers or make scratches on discs. • Do not warp discs.
TAPE NOTES 1. 2. 3. 4. Take care of your tape cassette to preserve the quality of the recordings. Do not allow them to be exposed to direct sunlight. Store them in a place protected from dirt and dust and avoid handing with greasy or oily hands. Also, keep the away from magnets, and motors of the permanent magnet type. It is not advisable to use cassette tapes longer than C-60 (30 minutes per side) in automobile players, since the tape is too thin and tends to become easily entangled.
INSTALLATION NOTES: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
INSTALLATION 1. 2. 3. 4. 5. Install brackets and screws removed from your old radio (not provided with this unit). Slide unit and frame into dash opening. Trim ring has precutgrooves on the back of it. The size of the trim ring can be reduced (made smaller) for different types of installations. Hold the trim ring firmly in one hand, and using a pair of pliers, grasp the trim ring above the score line (groove) and bend gently back and forth a couple of times. Then the piece should break away.
INSTALLATION CAUTION: DO NOT INSTALL THE DETACHABLE PANEL BEFORE CONNECTING THE WIRE. 1. The unit is designed for negative terminal of the battery which is connected to the vehicle metal. Please confirm it before installation. 2. If the car interior is extremely hot, as after being parked in the sun, do not use the player until the car has been driven for a while to cool off the interior. 3. Press the REL button to take away the front panel (see fig.1), and put it in the protective case (see fig.
ELECTRIC CONNECTION MAIN UNIT ANTENNA CONNECTOR FUSE IGNITION SWITCH (B+) MEMORY BACK-UP (B+) RED YELLOW FUSE BLACK GROUND (B–) POWER ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER BLUE FUSE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIIOLET/BLACK DESCRIPTION OF RCA JACK (ON THE BACK OF THE UNIT) FRONT RCA OUTPUT V. OUT = VIDEO OUT FL OUT = FRONT LEFT AUDIO OUT FR OUT = FRONT RIGHT AUDIO OUT AUXILIARY IN V. IN = VIDEO IN L. IN = LEFT AUDIO IN R.
REMOTE CONTROL 11 1 MODE POWER CLK 12 13 2 3 BAND 5 7 STOP PLAY/PAUSE MUTE ST/MO ANGLE REPEAT TITLE/PBC LO/DX 14 SETUP 4 OSD 6 SEL 8 16 EQ A/P 18 + UP 15 17 19 F.FWD NEXT VOL ENTER F.BWD PREV. VOL 20 DN - 9 1 2 3 4 5 6 7 8 9 0 +10 21 SW 10 1. 2. 3. 4. MENU CLK MODE SETUP OSD (BAND) 22 Press it to change the display to clock display. Press it to change between radio or disc mode. Display the SETUP menu.
REMOTE CONTROL Preparing the Remote Control Inserting the Batteries 1. Open the battery compartment cover. 2. Insert the new batteries.Make sure that the positive and negative terminals of the batteries are oriented indicated. 3. Close the cover Using the Remote Control Face the remote control towards the player front face IR mark (remote control signal receiver). Operation angle: About ± 30 degree in each the direction of the front of the IR mark.
BASIC OPERATION 1 16 5 19 13 CAR DVD/VCD/CD/MP3 CASSETTE RECEIVE ST TAPE IN 2 18 26 3 6 24 7 8 25 14 15 12 23 21 11 9 10 11 22 4 20 17
BASIC OPERATION 1. OPEN BUTTON Press it to flip down the front panel then you can insert the TAPE into the tape compartment. 2-3. VOL +/ VOL- & SEL BUTTON Press it to change audio mode through volume, bass, treble, balance, and fader modes. Use VOL +/ VOL- buttons to adjust the selected mode. When mode has not been adjusted for several seconds, display returns to normal radio or CD display. VOL BAS TRE BAL FAD A. Volume: Adjust volume level by using VOL +/ VOL- buttons.
BASIC OPERATION a. Continuously repeat at the current chapter/track, when selected REP-ONE mode. b. Select REP-ALL mode to continuously repeat all chapter/track on the current disc. c. REPEAT feature does not support VCD2.0 (with PBC ON). E. Press 3/INT button to scan disc. a. In the state of VCD/CD disc playing, press the 3/INT button on the front panel to play the previous 10 seconds part of each track/chapter on disc (depend on the disc used for VCD). b.
BASIC OPERATION 17. / BUTTONS / button (more than 2 seconds) during play, A. When long pressing the the speed of rapid forward/reverse changes according to the disc as follow. DVD: VCD/ C D : Normal Playback 2X 4X 6X 8X Normal Playback 2X 3X 4X MP3: Normal Playback 2X 4X B. Shortly press the / button during playback to skip to next track or back one track. Note: For some VCD2.0 discs (PBC-playback control), and buttons may be unavailable. C.
BASIC OPERATION 24. FLASHING LED If the front panel is not on the main unit, LED will be flashing. 25. RESET BUTTON RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: A. Initial installation of the unit when all wiring is completed. B. All the function buttons do not operate. C. Error symbol on the display.
BASIC OPERATION c. Press OSD for the third time: On-Screen Display Function Press the OSD button during playback to display the contents of the current disc on the screen. T:01/18 P: 00:00:25 LR TOTAL ELAPSED A. Example for DVD: d. Press OSD for the fourth time: a. Press OSD for the first time: T:01/18 P: 00:00:25 LR TOTAL REMAIN TITLE 01/03 CHAPTER 002/025 P:00:00:25 TITLE ELAPSED Note: For CD and Mp3, the message will always display on the screen. C.
BASIC OPERATION Multi-subtitle Language Function (For DVD only) Press SUBTITLE during playback. Each time the button is pressed, number of the subtitle language changes in sequential order. Notes: The language number is different according to the disc. Some discs only contain one subtitle language. When no different subtitle language are recorded, will be displayed at screen left top corner. Multi-audio Language Function A. DVD: Press AUDIO during playback.
SETUP INITIAL SETUP GENERAL SETUP --- MAIN PAGE--- --- GENERAL PAGE --- GENERAL SETUP TV DISPLAY NORMAL/PS SPEAKER SETUP PIC MODE NORMAL/LB AUDIO SETUP ANGLE MARK WIDE PREFERENCES OSD LANG CAPTIONS SCR SAVER EXIT SETUP 1. Press SETUP in the stop mode. (Press the stop button twice to ensure the player under STOP mode.) MAIN PAGE TV Screen 2. The initial SETUP menu is displayed. 4:3 Video Material Normal 3. Select the preferred item by using the / buttons.
SETUP --- GENERAL PAGE --- --- GENERAL PAGE --- TV DISPLAY TV DISPLAY PIC MODE AUTO PIC MODE ANGLE MARK HI-RES ANGLE MARK OSD LANG N-FLICKER OSD LANG CAPTIONS CAPTIONS SCR SAVER SCR SAVER MAIN PAGE MAIN PAGE ENGLISH 2. PIC MODE SETUP Select AUTO, the player PIC mode will depend on DVD disc. Select HI-RES format for best image resolution. Select N-FLICKER format on format on image or picture under noise affect. 4.
SETUP --- GENERAL PAGE --- AUDIO SETUP --- AUDIO SETUP --- TV DISPLAY PIC MODE AUDIO OUT ANALOG OP MODE SPDIF/RAW LPCM OUTPUT SPDIF/PCM ANGLE MARK OSD LANG CAPTIONS DYNAMIC SCR SAVER ON OFF MAIN PAGE SCR SAVER SETUP Select the SCR SAVER output ON/OFF. MAIN PAGE 1. AUDIO OUT This is to activate the audio output from ANALOG mode to SPDIF/RAW mode to SPDIF/PCM mode.
SETUP --- AUDIO SETUP --- PREFERENCES SETUP --- PREFERENCES PAGE --- AUDIO OUT TV TYPE MULTI OP MODE AUDIO NTSC LPCM OUTPUT SUBTITLE PAL DYNAMIC LPCM 48K DISC MENU LPCM 96K PARENTAL PASSWORD DEFAULTS SMART NAV MAIN PAGE MAIN PAGE 1. TV TYPE SETUP This player can play discs recorded in either PAL or NTSC format. Select NTSC format, when you connected to NTSC TV. Select PAL format, when you connected to PAL TV.
SETUP --- PREFERENCES PAGE --- --- PREFERENCES PAGE --TV TYPE TV TYPE 1G AUDIO AUDIO 2 SUBTITLE ENGLISH SUBTITLE 3 PG DISC MENU FRENCH DISC MENU 4 PG 13 PARENTAL SPANISH PARENTAL 5 PASSWORD CHINESE PASSWORD 6 PG-R DEFAULTS JAPANESE DEFAULTS 7 NC-17 SMART NAV OFF SMART NAV 8 ADULT MAIN PAGE NO_PARENTAL MAIN PAGE 3. SUBTITLE LANGUAGE SETUP Select the preferred SUBTITLE language by using the cursor buttons. 5.
SETUP --- PREFERENCES PAGE --- DEFAULTS TABLE TV TYPE General Setup TV Display AUDIO SUBTITLE PIC Mode AUTO Angle Mark ON OSD Language English DISC MENU PARENTAL PASSWORD DEFAULTS Normal/PS RESET Captions OFF SCR Saver OFF Speaker Setup Downmix Stereo Audio Setup Audio Out Analog OP Mode SMART NAV Line Out Dynamic MAIN PAGE LPCM Out Preferences TV Type 7. DEFAULTS Select reset to become factory initial setting.
SPECIFICATIONS Supply voltage Current consumption Signal system Discs played : : : : Audio Signal Output Characteristics : : TAPE SECTION Wow & Fluter S/N Ratio (Normal) Separation Frequancy response : : : : 12V DC (11V-15V) Less than 10A Compositive video 1.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory terminal,switch the ignition key to “ACC“. The fuse is blown. Replace the fuse.
88-V2940-01