Product Brochure

5454
UNDER-CABINET LIGHTING & POWER SYSTEMUNDER-CABINET LIGHTING & POWER SYSTEM
How to Specify the System
The adorne Under-Cabinet Lighting System is a fully customizable and modular solution for eliminating kitchen clutter. It is compatible
with any kitchen layout, such as a galley, L-shaped, or U-shaped, as well as with any home wiring. In order to ensure you have specified
the correct products for your system, we recommend you follow the steps outlined below.
1. Planning Your System Layout
First, determine where you want to install the system.
Then measure your cabinets to determine the length of
Modular Track required:
• Measure each cabinet length at back of cabinet.
• For installations with a corner, allow 3” on each side
for Corner Connector.
• When totaling up the length of required Modular Track,
be sure to include the length of the desired Control Box or
Direct Wire Connector. For a 1-gang box, allow 5”.
For a 2-gang box, allow 5.25”. For Direct Wire Connector,
allow 6”. For more detail on Control Box options, see page 53.
• If your selection of Modular Tracks does not match the exact
length of your cabinets, you can use a Modular Track Extender
to complete the track. This piece can be cut down to 6”.
Standard 12”, 18”, and 27” Modular Tracks cannot
be shortened.
2G
1G
1G
18
27
27
18
27
18
12
EX
12 EX DWC27 2718
c
c
c
(cut to 6.75”)
(cut to 9.75”)
12” Modular Track
18” Modular Track
18” Modular Track Extender
Modular Track Corner Connector
27” Modular Track
• One 2-Gang Control Box is placed at
one end of system for hardwired power
connection and lighting control
• Total length of cabinets can be exactly
matched with combination of standard
Modular Tracks
• As needed, Control Boxes can be placed
anywhere in system
• 1-Gang Control Boxes are placed
at both ends of the system for hardwired
power connection and lighting control
• Modular Track Extender is custom-cut
to match exact length of cabinets
• Direct Wire Connector is placed at
one end of system for hardwired
power connection
• Light control located in nearby wallbox
• GFCI circuit breaker located in
electrical panel
*
Sample Installation: Length of cabinets is equal to
combined length of standard Modular Tracks
Sample Installation: Length of cabinets is greater than
combined length of standard Modular Tracks
Sample Installation: Direct wire with system controls
in a remote location
56”
57”
60”
42”
36”
36”
Visit www.adornemyhome.com to watch planning and
installation videos.
5555
9” Modular Track
2. Selecting the Control Box and Power Options
Next, select the type of lighting and power connection you’d like to include. For a hardwired installation, there are five options to
choose from which enable expanded lighting control options such as dimming:
• Control Box with Paddle Dimmer
• Control Box with Paddle Dimmer and GFCI protection
• Control Box, 1-Gang (No Devices)
• Control Box, 2-Gang (No Devices)
• Direct Wire Connector
For hardwired installations, there must be three separate circuits from the electrical panel:
• Receptacle Circuit: 20 Amps; GFCI-protected; Use #12 wire
• Lighting Circuit: 15 Amps; Use #12 or #14 wire
• Accessory Circuit: 15 Amps; Use #12 or #14 wire
Compatible with all adorne 2-module devices. The CFL/LED Paddle Dimmer (ADPD453LM2) is recommended for use with the adorne system.
3. Selecting the LED Lights
The adorne Under-Cabinet Lighting System is only compatible with adorne LED lights. Recommended placement for lights is every
18” along Modular Track.
You can select any combination of Linear lights to complete your system. In addition, if you are mounting a light under the cabinet
and wish to move it further to the front of the counter, you can use the LED Light Extender. This enables you to increase the length
of any light from the Modular Track from a standard 11” to up to 22”. This is especially useful in corner installations.
4. Choosing Accessories to Complete the System
The final step is to select the accessories to perfectly complement your system. adorne offers a range of options, including USB
charging ports, mobile and tablet cradles. Each of these accessories provides flexibility in that it can be added or removed at any
time – simply swap it with an existing outlet or blank module to increase your system capabilities.
2-Gang Control Box
with Paddle Dimmer
and 15A GFCI
1-Gang Control Box
with Paddle Dimmer
Direct Wire Connector Control Box,
No Devices, 1-Gang*
Control Box,
No Devices, 2-Gang*
LED Linear Light Light Extender
Hardwired Control Boxes
We’re here to help!
We have a dedicated project services team on staff to help you plan your projects, including supplying a full takeoff
with a wiring diagram based on your floor plans.
Give us a call at 315.468.8413 or email us your project info at [e-mail].
LED Slimline Light