Installation Guide

3
Catalog No./Item Description/Specifications
B13-14 External Elbow – For outside
Internal Twisted Elbows – For 90°
twist with 90° turn including a flat
run on sidewall to a flat run on
ceiling or on door edge or window
trim.
B16 Tee – For branches at right angles.
B81 Box Connector (Galvanized) –
For connecting raceway to conduit
boxes, panel boxes, etc., having a
KO for conduit. May also be used
with conduit type fittings.
B17 Combination Connector – For
connecting raceway, without
offsetting, to any 3 1/4" [83mm] or
4" [102mm] outlet box mounted
on the surface with a KO for 1/2"
[12.7mm] conduit. The base end
and bottom has two 1/2" trade size
KOs. Break off cover extension to
use with 700 Series. Spring steel
bushing included for end connection
to box, eliminating conduit nipple
and locknut.
V57240 15A, 125V Single Pole Switch
and Box – Accommodates other
standard single-gang switches in
place of furnished standard single
pole switch. Cover has twistouts
on each end. Twistout on ends
permits running raceway
close to interior trim. Base
has 1/2" trade size KOs.
V57242 Utility Box – For use as tee, cross,
pull box, junction box, blank box,
etc. Cover has 1/2" trade size
KO and twistouts on each end and
side. End twistouts permit running
raceway close to interior trim. Base
has 1/2" trade size KOs.
Catalog No./Item Description/Specifications
V500+ Raceway – .040" [1.0mm] steel.
Comes in 10 ft. [3.05mm] lengths,
one 5701 Coupling furnished
with each length. Five ft. [1.525m]
lengths also available, order part B1.
B9-10-11 Accessory Pack – Includes:
Bushing – Protects wires from
abrasion. Bushing slips into open
end of raceway where it enters
a fitting.
Mounting Strap (1- or 2-Hole) –
Convert to one-hole by breaking off
at score. Lanced tab holds strap in
place while fastening to surface.
Connection Cover – To cover
openings where lengths of V500
Series Raceway, not squarely cut,
come together.
Coupling – For joining and
supporting lengths of V500
Series Raceway. One coupling
supplied with each length.
Supporting Clip – For supporting
lengths of V500 Series
Raceway at any point desired.
B6 90° Flat Elbow – For right angle
turns on same surface.
B7 Inside Elbow – For inside
surfaces at right angles.
B8 Outside Elbow – For outside
surfaces at right angles.
V500 Series Raceway Accessories Ordering Information
2 3/4"
[70mm]
NOTE: Use #6 flat head screws with all fittings requiring screws except V504/V704, and V57200 Series; with V504/V704 use #8 pan head
screws; with V57200 Series use #8 flat head screws.
3/4"
[19.1mm]
17/32"
[13.5mm]
3/4"
[19.1mm]
2"
[51mm]
2"
[51mm]
2 1/2"
[64mm]
2 1/2"
[64mm]
2 1/2"
[64mm]
2 1/2"
[64mm]
7/8"
[22.2mm]
2 1/2"
[64mm]
2 1/2"
[64mm]
1/2" [12.7mm] Male (5781)
3"
[76mm]
1 5/16"
[33mm]
1 3/8"
[33mm]
1/2"
[12.7mm]
3/4"
[19.1mm]
2"
[51mm]
1 3/8"
[35mm]
4 1/8
[105mm]
2"
[51mm]
1 3/8"
[35mm]
4 1/8"
[105mm]