Table of Contents Page 3 Page d Page 5 Page Page? Paged Introduction NYP100-xx Single Zone Player Front and Back Panel Features NYP200-xx Single Zone Player Front and Back Panel Features NYP3100-xx Trippe Zone Player Front and Back Panel Feature: NYP3500-xx Triple Zone Player Front and Back Pane! Features... NVP30G-xx Singe Zone Pr-Amplifier Front and Back Pane! Feature: 1. Institutionalization 1.1 Network Requirements . 1.2 Connecting the Gateway to the Ne two 1.
acidulous Welcome tu the exciting world of the Null Player Portfolio Audio System. Now your favorite music, In any room yon want t, anytime you want It, is as close as the touch of a button en any of your Apple or Android WI-Hl enabled portable devices. True high fidelity music, from your own personal library or streaming from the Interact, is more Alford able and accessible than you ever imagined. This is your guide to quickly and easily filling a home with music.
1, Volume Own: Press io decrease audio volume, 2, Volume tp: Press to increase audio volume, 3. Mute: Press to audio, 4. LED Indicator: Indicates status of NYP100-xx {see table in section 6.1 for details). stings Tone Player Back Panel Features (Wireless or Ethernet Connectivity) 1. Ethernet: This RIS port allows for a wired connection directly to the NVGW100-xx Gateway or directly to the Newark router, 2.
£ Panel Spitfires Wireless wr Filibuster Connectivity Volume Down Press to decrease audio volume, 2, Volume Upp: Press to Increase audio volume. 3. Mute: Press to mute fun-mute audio, 4, Bluetooth: Press to cause the NVP200-xx to change to the next paired device in the fist, Press and hold to break any current connections, become discover able, and accept paling requests. 5. LED Indicator: Indicates status of NVP200-ux {see table in section 6.1 for details).
satiates Theme Conglomeration) Standby LED Indicator: Indicates whether the NYP3100-iis powered on, and whether iris in active or standby mode. 2. Zone 1LE Indicator: Indicates status of HYP3100-x Zone Ti see table In section 6,1 for details). 3. Zone 2 LED Indicator: indicates status of HVP3100-1x Zone 2 {see tale in section 6.1 for details), 4. Zone 3 LED Indicator: Indicates status of HVP3100-xx Zone 3 (soe table in section 6.1 for details).
1. Power Button: The Power button toggles the power on and off to the NYP3500-xx component. [tis alas used in the reset procedure for each of the zones. 2. Setup Buttons: Each of the three zones housed in the NYPI500-xx have a separate setup doubloon used in the initial system setup process, These buttons are also side in the zone est procedure, When the system is set up, each zone has an associated LED that Indicates that zones power status (see table in section 6.
1. Exhume Down: Press to decrease audio volume, 2, Volume Up: Press te kinase audio volume. 3, Mute: Press to mute fun-mule audio. 4. LED indicator: Indicates status of NVP300 {see table in section 6.1 for details). T. Audio fn; This is a combination 3.5mm steed line level and mint TO SUNK apical Input. This input will automatically decipher the difference between an analog ne level input and TO SLINK apical input.
tin Alive Internet connection s necessary for complete setup, operation, and music enjoyment of your Site Player Portfolio Audio System. Once the system is set up and run nine, interned is not necessary for listening to music streaming from a network source. For wired Ethernet connectivity a minimum 100mb wired network is necessary for ‘proper communication. This should not be penetrable.
te Make sure that the installation's router is connected to the network modem (this Is generally supplied by the Infest Service Provider, ISP) with a single CATS network cable. The Gateway has five Theme ports and acts as a standard Ethernet switch. Simply connect the included able, or any Ethernet cable with a standard RIDS modular plug, nits one of the five ports on the back of the Gateway and connect the other end Into an available port on the back of the installation’s router, as shown in fig. 3. Fig.
sig the HYP100wg and MYP3500-xx Zone Players {yor are installing the NUP3100-xc or HYPNOSES-xx rack mount component, the network connection is completed by connecting one of the KVP3100-sx {or NYP3580-301} tw Ethernet ports directly to the home's network using a standard Theme cable. Either of the twa Ethernet ports will communicate when connected, as shown in fig, 5. The second port is used for daisy chaining multiple P3100 or P3500 units for more audit zones, as shown in fig.
Sy Sealers vo the BYPATH-0 and PREYED-0 The NYP T00-xx and WXP200-%t zone players are equipped with “5-way” binding posts far connecting the amplified audio signal to speakers, These can be bookshelf, flora standing, er installed in the wall or ceiling. 16 gauge speaker wire is recommended for this purpose, The binding posts provide five different methods far terminating the wire. The post can be ascribed to expose a bole for the speaker wire.
a System Finn the HIS or Android App nce you have connected the system to the local network you are ready ta begin adding components in this desired locations, naming those locations for local control and creating your multi-zane music system, The process easily done from any Pod Touch, Phone, iPad, or Android device using the Nutted Wireless Audio System app.
The next step is to place your first component in its devised location. When ts plugged in and powered on, the front LED light wil flash white wile the player is booting up. When iris ready the front panel LED will be solid green, Touch the “Next” button to proceed to the next step, as shown in fig. 13.
White the connection Is being made, the front panel LED will flash. The app will indicate when the connection Is complete and the LED wil be solid white, Touch "Next" to proceed, as shown in fig, 15. 3 \ The "Add" button will repeat the setup process for the next zone, If you have completed the setup on alf of the desired zones, touch the “Done” button. The app wi go te the hammer screen, deferred to as the Dashboard view, as shown In fig.
1 Eugenicist Systems Once a system is set up, adding additional TYPING-xx, BYPLAY-xx, P1100, NVP3500-3¢ or NYP30U-x zone players is easily done. Tod this, go to the “Settings” button at the bottom of the Dashboard, which is the section of the app defined by the zone icons, as shown in fig. 19, Fig. 20 Touch the “Add a Hugo Component” but ton as shown in fig. 20. This wil take you 1 the zone setup procedure described fi section 2.
Additional Gateways tn an Blasting System Up 10 two additional Gateways can he added to 3 system when additional WI-F range Is needed, Additional Gateways must be hardwired to the network along with the aright nal Gateway. This can be done by plugging the new Gateways) into the fist Gateway, Into the installations router, or a switch from the router. When a new Gateway Is added 10 the system, ge to the Settings menu and select “Add a Nuncio Component”, as shown in fig. 21.
