Installation Guide

WIREMOLD
®
Plugmold
®
Multioutlet Systems
Catalog Number(s): PM22XX-USB
Country of Origin – Made in China
I MPORTANT:
Please read all instructions before beginning installation.
Legrand electrical systems conform to and should be properly
grounded in compliance with requirements of the current National
Electrical Code or codes administered by local authorities.
All electrical products may present a possible shock or fire hazard
if improperly installed or used. Legrand electrical products may
bear the mark of a Nationally Recognized Testing Laboratory and
should be installed in conformance with current local and/or the
National Electrical Code.
No: 1021111_A – 0318 Installation Instructions
WARNING! Loss of ground continuity can cause electrical hazard.
Do not apply additional paint inside of base.
No: 1021111_A – 0318
© Copyright 2018 Legrand All Rights Reserved.
860.233.6251
1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca
NOTE: Not for temporary installation. Mount on a permanent surface.
NOTE: Installation can be completed by back feeding, end feeding or
coupling to another Plugmold unit.
IMPORTANT: This product must be provided with GFCI and AFCI protection
when installed in kitchens and GFCI protection when installed
in bathrooms. Refer to latest National Electrical Code for
more details.
Tools & Fasteners Required:
• Drill
• Tape Measure
• Pencil
• Phillips Screwdriver
• Slotted Screwdriver
• Wire Stripper
• Hammer/Rubber Mallet
• Pliers
• Mounting Hardware (See Step 4)
2 Blank End Fittings (Not installed)
Cover
EACH PLUGMOLD PACKAGE INCLUDES
USB Receptacle 5V, 3.1A Prewired
2 Grounding Type Receptacles 15A, 125V Prewired
2 White W30 Connectors & 1 Green W30G Connector
1/2" Trade Size Entrance Knockout
Coupling
Mounting Hole
Select permanent surface to mount to, including
a wall or underside of a cabinet.
1
INSTALLATION:
Cabinet
Wall
Cabinet
Wall
BACK FEED WIRING THROUGH ENTRANCE KNOCKOUT
Remove a 1/2" trade size entrance knockout using a slotted screwdriver
and rubber mallet or hammer. Protect counter top or work surface by
covering with cardboard or a cloth prior to attempting to remove knockout.
With base in orientation shown, strike at point between holding tabs. Twist
out using pliers.
Attach 1/2" trade size feed connector (not included) per manufacturer's
instructions to knockout opening.
2
NOTE: Feed Connector shown for reference only (Not included).
COVER INSTALLATION
Engage lower bead of cover in base. Starting at one
end and progressing along unit, snap in upper bead
by STRIKING SHARPLY WITH HEEL OF HAND. If
necessary, a rubber mallet can be used to attach cover.
6
COVER REMOVAL
Use two screwdrivers, progressing along raceway as shown.
Cover
FIGURE C – W30 & W30G Connectors
W30 – Common connection of 2, 3 or 4 solid conductors No.14 or No.12 AWG.
W30G – For connection of equipment grounding of 2, 3, or 4 solid conductors No.14 or No.12 AWG.
Rating – 300 volts maximum, 20 AMP. 105° C maximum.
NOTE: W30 Connector has a white finish, W30G Connector has a green finish.
S
TR
IP
G
A
G
E
A. Strip wire ends to width of product (1/2" [12.7mm]).
B. Insert wire ends the full stripped distance.
2000USB, 2000TR, 2000TRUSB, 2000 TRUSBA Series Raceway Wire Fill Capacities for Power
CABLE TYPE WIRE SIZE
THHN/THWN
O.D. NO. OF CONDUCTORS (40% FILL)
Inches [mm] 2000TRUSB
POWER WIRING
WITH DEVICES
(Plugmold Series)
12 AWG 0.122 [3.1] 3**
14 AWG 0.105 [2.7] 3**
**Including one hot, neutral, and ground wire from the receptacle.
PLUGMOLD SERIES WIRING SPECIFICATIONS
Base