Installation Guide

ManualsBrandsLegrand ManualsElectricalRadiant Smart WiFi Outdoor Tri-Tap Plug-In Switch with GFCI, Black

Smart Plug-In Outdoor

Switch, Wi-Fi

Summary of content (12 pages)

PAGE 1
Smart Plug-In Outdoor Switch, Wi-Fi
PAGE 2
before you start Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities. Caution: To reduce the risk of injury and/or overheating and damage to other equipment: • Connect the smart plug-in switch to a 120 VAC, 60 Hz power source ONLY. • To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet.
PAGE 3
general Legrand’s Smart Plug-In Outdoor Switch with GFCI function provides personal ground fault protection. Conventional over-current protection devices such as fuses and circuit breakers cannot protect people from electrical shock. Those devices are designed to disconnect the power when currents of several amperes flow from the hot wire to ground. However, currents as low as a few milliamperes can be dangerous to normal healthy human beings. One ampere equals 1000 milliamperes.
PAGE 4
installation 1 | Plug unit into 120 VAC power socket protected by fuse or circuit breaker. 2 | With no load connected the unit will automatically become energized and the indicator will blink green and amber after 10 seconds. 3 | Press “Test/Off” button. 4 | Verify the lamp indicator changes to blink white and amber (this step denotes that power is off). 5 | Press and release “Reset/On” button for use. 6 | Connect the desired load equipment to cord receptacle and operate equipment normally.
PAGE 5
setup up your system a Download and launch the Smart Lights, Wi-Fi app by Legrand. The app is available on the App Store or on Google Play. SCAN TO DOWNLOAD b Connect your Smart Plug-In Outdoor Switch to your home network by following the step by step instructions in the app. c Use the app to control your Smart Plug-In Outdoor Switch. SCAN TO WATCH HOW TO SET UP THE APP Google Play and the Google Play logo are trademarks of Google LLC. App Store is a service mark of Apple Inc., registered in the U.S.
PAGE 6
getting to know your switch Item Name Description 1 LED Locator Light 2 Off Button 3 On Button • Indicates the current state of the device. See LED locator Light Explanations for detail. • Turns the device off. Also used to test GFCI function. • Turns the device on. Also used to reset the GFCI function. LED LOCATOR LIGHT EXPLANATIONS LED State of Color Light Explanation Green Blinking Amber Device is attempting to connect to the network.
PAGE 7
warnings If the GFCI fails to trip when the Test button is pressed (lamp indicator fails to turn white) or, if the GFCI fails to reset when the Reset button is pressed (lamp indicator fails to remain green), the device should be replaced. If the GFCI tests properly without any appliance plugged into it, but trips each time the appliance is plugged in, the appliance has a ground fault and needs to be repaired or replaced. DO NOT BYPASS THE GFCI. IF THIS CONDITION OCCURS, A REAL SHOCK HAZARD MAY EXIST.
PAGE 8
regulatory information FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 9
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the transmitter’s radiating structure(s) and the body of the user or nearby persons. NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.
PAGE 10
specifications Load Rating Resistive Incandescent/halogen Ballast Motor LED 120 VAC, 60 Hz,15 A 1800 W 15 A standard/electronic 1/2 HP 5A Legrand reserves the right to change specifications without notice. notes Legrand’s Smart Plug-In Outdoor Switch will provide protection against ground faults when used with a 2-wire outlet receptacle and a 3-wire to 2-wire adapter.
PAGE 11
questions? we're here to help PHONE: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F) EMAIL: smartlighting@legrand.us CHAT: https://www.legrand.us/radiant/smart-lighting.