TM Leica DISTO touch TMD810 Leica DISTO X310 The original laser distance meter The original laser distance meter The original laser distance meter
Table of Contents Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Basic measuring screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Selection screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 Pointfinder (Viewscreen) - - - - - - - - - - - - - - - - - - - - - - - -
Instrument Set-up Introduction EN Overview The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them. The symbols used have the following meanings: Display WARNING Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
Instrument Set-up Basic measuring screen EN Selection screen Status bar FUNC Function / Settings Main line Active function Tap here to start ON/DIST in a distance function Settings Help function Favorites Leica DISTOTM D810 touch 799093 3
Instrument Set-up Pointfinder (Viewscreen) EN Zoom stage 1x Illumination adjustment with navigation keys left and right Active function Crosshair 24.
Instrument Set-up Charging the Li-Ion battery via USB EN Charge the battery before using it for the first time. Use the provided cable to charge the battery. Plug the small end of the cable into the port of the device, and plug the end of the charger into an electrical socket. Select the appropriate connector for your country. The device cannot be used while it is charging. The computer can also be used to charge the device, but this takes more time.
Operations Using the Touch Screen i EN Use only fingers to use the touch screen. Do not allow the touch screen to come into contact with other electrical devices. Electrostatic discharges can cause the touch screen to malfunction. Do not allow the touch screen to contact water. The touch screen may malfunction in humid conditions or when exposed to water. To avoid damaging the touch screen, do not tap it with anything sharp or do not apply excessive pressure to it with your fingertips.
Operations Switching ON/OFF ON EN Clear OFF i 2 sec 1x If no key is pressed for 180 sec, the device switches off automatically. Device is turned OFF. Message Codes 2x If the info icon appears with a number, observe the instructions in section "Message Codes". Example: Leave actual function, go to default operation mode. Undo last action. Multifunctional endpiece i The orientation of the endpiece is automatically detected and the zero point is accordingly adjusted.
Operations Add / Subtract EN 2x 1 2 7.332 m 3 The next measurement is added to the previous one. The next measurement is subtracted from the previous one. i 4 7.332 m This process can be repeated as required. The same process can be used for adding or subtracting areas or volumes. 20.179 m 12.847 m Pointfinder (Viewscreen) 1x 1 1x 2 4x 3 4 2x 0.00m i 1x 0.00m Exit pointfinder (viewscreen). OV* This is a great help for outdoor measuring.
Operations Screenshot 2 sec EN 1x 1 0.00m Leica DISTOTM D810 touch 799093 Screenshot photo is saved in gallery.
Settings Overview 1 EN Tilt units Distance units Beep Digital level Keypad lock Bluethooth® Smart Tilt calibration Favorites Illumination Touch screen Date and Time Compass adjustment Offset Reset Information 2 Tilt units 1 2 3 Switch between the following units: 360.0° 0.00 % ± 180.0° 0.0 mm/m ± 90.0° 0.00 in/ft Leica DISTOTM D810 touch 799093 4 5 Confirm setting. Exit settings.
Settings Distance units EN Art. No. 792297: 1 2 3 Switch between the following units: 4 0.00 m 0.000 m 0.0000 m 0.0 mm 0.00 ft 0.00 in 0 in 1/32 0'00" 1/32 US-Model Art. No. 799097: 0.00 m 0 in 1/16 0.000 m 0'00" 1/16 0 in 1/8 0.0000 m 0.0 mm 0'00" 1/8 0.00 ft 0 in 1/4 0.00 in 0'00" 1/4 0 in 1/32 0.000 yd 0'00" 1/32 5 Confirm setting. Exit settings.
Settings Beep ON/OFF 1 EN 2 3 Exit settings. To switch ON, repeat procedure. OFF ON Digital level ON/OFF 1 2 i 3 To switch ON, repeat procedure. Exit settings. OFF ON De-/Activate keylock 1 Switch on with keylock To deactivate, repeat procedure. The keylock is active if device is 3 switched off. 2 1 Exit settings. OFF Leica DISTO TM The digital level is displayed in the status bar.
Settings Bluetooth® Settings 1 EN 2 OFF ON i OFF i 3 Explanation see info box below. Exit settings. Default mode: Bluetooth® is switched on and black Bluetooth® icon is displayed in status bar. Blue Bluetooth® icon in status line is displayed if device is connected with Bluetooth®. OFF Switches Bluetooth® off. Figure Mode: Use this mode if the data needs to be transferred in figures, e.g. working with spread sheets. Ft/in fractional is converted into ft/in decimal.
Settings Calibration of tilt sensor (Tilt Calibration) 1 2 EN 3 4 180° Place device on absolutely flat surface. 180° 5 6 7 Turn the device horizontally by 180° and place it again on absolutely flat surface. 8 Place device on absolutely flat surface. 9 180° 180° 10 i After 2 sec the device goes back to the basic mode. Turn the device horizontally by 180° and place it again on absolutely flat surface.
Settings Personalized favorites EN Favorite 1 2 3 4 Select favorite function. i 5 Press selection key left or right. Function is set as favorite above the corresponding selection key. Select your favorite functions for quick access. Short cut: Press 2 sec on a selection-key in the measuring mode. Exit settings. Illumination 1 2 3 4 1/6 2/6 3/6 4/6 5/6 6/6 1/6 i 5 Confirm setting. Exit settings. To save power reduce brightness if not necessary. Select brightness.
Settings Compass Adjustment EN Adjusting the magnetic declination i Depending on your geographic location, the angle of declination may vary from other locations, as the geographic and magnetic poles are aligned. However, if the reference location is not selected, the difference in declination between the poles can differ greatly. For best results, select the nearest geographic reference point using the steps below.
Settings Offset 1 EN 2 3 4 Select digit. i 6 Exit settings. 1.012 m 5 1.012 m Adjust digit. Approve value. An offset adds or subtracts a specified value automatically to or from all measurements. This function allows tolerances to be taken into account. The offset icon is displayed. Reset Second confirmation with selection keys: 1 2 3 Refuse: Confirm: i 4 Exit settings. Leica DISTOTM D810 touch 799093 Reset returns the instrument to the factory settings.
Functions Overview EN Timer Triangle Area Calculator Long Range Mode Adjusting measuring reference Height-profile Measurement Memory Measuring on sloped objects Sinlge Distance Measurement Height Tracking Smart Horizontal Mode Trapezium Level Stake out Area Pythagoras (2-point) Volume Pythagoras (3-point) Photo Width Compass Diameter Gallery Area from Photo Timer 1 2 3 30 sec 10 sec 5 sec 2 sec Off Leica DISTOTM D810 touch 799093 i 4 Select release time.
Functions Calculator 1 EN 2 Select key on display. 3 Confirm every key. C/CE = Use selection keys for clear or result. i The measurement result from the main line is taken over to the calculator and can be used for further calculations. Ft/in fractions are converted into ft/in decimal. To takte over a result from the calculator in the basic mode press DIST before leaving the calculator function.
Functions Memory EN Switch between measurements. 1 2 3 i 4 Delete memory. 8.449 m Take over value for further actions. Use Up/Down navigation keys to show more detailed results of the specific measurement. Short cut Measuring single distance 1 2 3 i 4 Aim active laser at target. 8.532 m Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or semi-permeable surfaces or when aiming at high gloss surfaces.
Functions Level 1 EN 2 i 0.3° 3 90° 0° Displays inclinations of 360° with a transverse inclination of +/- 10°. Instrument beeps at 0° and 90°. Ideal for horizontal or vertical adjustments. Area 1 2 3 4 5 Aim laser at first target point. 6.228 m 6 3.9I0 m 20.276 m 24.352 m 2 Leica DISTOTM D810 touch 799093 First distance Second distance Circumference Aim laser at second target point. i The result is shown in the main line and the measured value above.
Functions Volume 1 EN 2 3 4 Aim laser at first target point. 5.744 m 8 Second distance 2.431 m Third distance 32.653 m 3 Leica DISTOTM D810 touch 799093 6 7 Aim laser at second target point. First distance 2.338 m 5 9 Use Up/Down navigation keys to show more results. Aim laser at third target point. 2 13.430 m 2 Ceiling/floor area 39.300 m Wall areas 16.
Functions Photo EN 1x 1 2 3 4x 4 5 2x 1x Take photo. Exit. OV* i Tap on the camera icon in the middle of the bottom line to take a photo. For screenshots, press camera key for 2 sec.
Functions Compass 1 EN 2 3 0.0°N i At the following places the compass probably does not work correctly: • Inside of buildings • Close to high voltage lines (e.g. on train platforms) i The arrow always points to true north. Check that multifunctional endpiece is not folded out. Keep the device away from any magnet. 4 Exit. If an error message occurs, the device is tilted too much (>20° over the front / > 10° sidewise).
Functions Gallery EN 1x 1 2 3 1x 1x 1x 4 Exit. 2013 201 13 - 07 - 03_13:25 2013 0 - 303_13:25 - 077 - 03_13:25 03_13::25 2013 - _13:25 07 i If the device is connected to the computer via USB cable, you can download or delete the gallery. It is not possible to upload any data.
Functions Triangular area 1 EN 2 3 4 5 Aim laser at second target point. Aim laser at first target point. 8 4.248 m First distance 4.129 m Second distance 2.425 m Third distance 4.855 m 2 6 9 Use Up/Down navigation keys to show more results. 7 Aim laser at third target point. 33.60° 10.
Functions Height-profile measurement EN 5 1 2 3 4 5 4 3 1 0 REF REF Aim at additional points 1-x. 2x i 7 2.042 m 0.054 m Leica DISTOTM D810 touch 799093 d Horizontal distance to device h Height difference to reference point (REF). d 0 Aim at reference point (REF). 6 2 h Exit function. Ideal for measuring of height differences to a reference point. Can be also used to measure profiles and terrain sections.
Functions Sloped objects 1 2 EN 3 4 5 Aim laser at upper target point. 6 11.00 ° 30.367 m -3.440 m 5.452 m i P2 angle P2 distance Vertical height between both points 7 Aim laser at lower target point. Use Up/Down navigation keys to show more results. 39.10 ° -4.230 m Included angle between both points Horizontal distance between both points Distance between both points Indirect distance measuring between 2 points with additional results.
Functions Height tracking EN Px Px 1 2 3 4 5 P0 P0 Aim laser at upper points and angle/ height tracking starts automatically. Aim laser at lower point. Px -10.55 ° 29.89 ° 3.475 m P0 x 6.271 m -10.55 ° 7 = Tracking angle if device is turned on tripod y = Tracking height if device is turned on tripod y 6 z Stops height tracking. 6.271 m 44.80 ° 8.478 m P0 8 Use Up/Down navigation keys to show more results. i 7.
Functions Trapezium 1 EN 2 3 4 Aim laser at upper point. h y 70.80° 5.790 m 7 Use Up/Down navigation keys to show more results. Leica DISTOTM D810 touch 799093 x h 78.383 m2 20.9 ° y 13.459 m 16.440 m Aim laser at 2nd point.
Functions Stake out i EN Two different distances (a and b) can be entered to mark off defined measured lengths. a= b a= b 1 1 2 3 3 b b b b 4 1.012 m Select digit. 7 8 Approve value "b" and start measurement. Leica DISTOTM D810 touch 799093 2 a a 3 1 2 5 Adjust digit. Move device slowly along the stake-out line. The distance to the next stake out point is displayed. 1.012 m 0.240 m is missing up to next 0.625 m distance. 6 Approve value "a". Next stake out distance 0.
Functions Pythagoras (2-point) 1 2 EN 3 4 5 Aim laser at second target. Aim laser at first target. 6 25.133 m 21.383 m 13.207 m Leica DISTOTM D810 touch 799093 i The result is shown in the main line. Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement. We recommend to use the pythagoras only for indirect horizontal measuring. For height measuring (vertical) it is more precise to use a function with the inclination measuring.
Functions Pythagoras (3-point) 1 2 EN 3 4 Aim laser at first target. 24.298 m 8 21.264 m 23.018 m 20.571 m Leica DISTOTM D810 touch 799093 5 6 Aim laser at second target. i 7 Aim laser at third target. The result is shown in the main line. Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement. We recommend to use the pythagoras only for indirect horizontal measuring.
Functions Width EN 1x 1 2 B=1 6.42m 3 It is absolutely necessary to aim with the laser perpendicular to the object. -.--- m 1x 4 4x 2x 1x OV* Leica DISTOTM D810 touch 799093 5 If necessary, use the Zoom for precise aiming. * OV = Overview 16.42 m Select arrows with the cursor keys or by tapping on the display and adjust with softkeys. Corresponding width is calculated. 6 Exit.
Functions Diameter EN 1x 1 2 3 Ø Aim laser perpendicular to the middle of the round object. -.--- m 1x 4x 4 2x 1x OV* 6 7 Confirm measurement. Leica DISTOTM D810 touch 799093 5 If necessary, use the Zoom for precise aiming. 0.237 m * OV = Overview Use Up/Down navigation keys to show more results. 0.744 m 0.044 m2 Circumference Circular area Select arrows with the cursor keys or by tapping on the display and adjust with softkeys. Corresponding diameter is calculated. 8 Exit. 0.
Functions Area from Photo EN 1x 1 2 3 Aim perpendicular to the horizontal center line of the area. This area must be perfectly flat on the vertical plane. -.--- m2 4 2.015m 4x 2x 1x OV* Leica DISTOTM D810 touch 799093 5 If necessary, use the Zoom for precise aiming. * OV = Overview 9.232m2 Select arrows with the cursor keys or by tapping on the display and adjust with softkeys. Corresponding area is calculated. 6 Exit.
Technical Data EN Distance measurement Typical Measuring Tolerance* Maximum Measuring Tolerance** Typical Range* Range at unfavourable condition **** Smallest unit displayed Power Range Technology™ Ø laser point at distances Photos / Screenshots ± 1.0 mm / ~1/16" *** ± 2.0 mm / 0.08 in *** 200 m / 660 ft 80 m / 260 ft -0.1° / +0.2° Autom. laser switch off Autom.
Functions Distance measuring Min/Max measuring Permanent measuring Stake-out Addition/Subtraction Area Triangle area Volume Trapezium Painter function (area with partial measurem.
Safety Instructions EN The person responsible for the instrument must ensure that all users understand these directions and adhere to them. • Measuring distances • Tilt measurement • Data transfer with Bluetooth® Areas of responsibility Prohibited use Responsibilities of the manufacturer of the original equipment: Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Internet: www.disto.
Safety Instructions Disposal CAUTION Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations. The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Adhere to the national and country specific regulations.
Safety Instructions Déclaration FCC, applicable aux Etats-Unis Ce produit a été testé et ses limites ont été jugées conformes à celles prescrites pour les dispositifs numériques de classe B, décrites dans le paragraphe 15 des règles FCC. Ces limites ont pour but de fournir une protection raisonnable contre des interférences nocives dans une installation résidentielle. Les appareils de ce type génèrent, utilisent et peuvent rayonner de hautes fréquences.
Safety Instructions Use of the product with Bluetooth® EN Laser classification WARNING Electromagnetic radiation can cause disturbances in other equipment, in installations (e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals. Precautions: Athough this product conforms to the most stringent standards and regulations, the possibility of harm to people and animals cannot totally excluded.
Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems (ISO standard 9001) and Environmental Management Systems (ISO standard 14001). Copyright Leica Geosystems AG, Heerbrugg, Switzerland 2012 Original text (799093 EN) Pat. No.: Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) www.disto.
