Leica DISTOTM E7300 The original laser distance meter
Table of Contents EN Instrument Set-up -------------------------Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 2 2 2 Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 3 3 3 3 3 3 4 4 4 4 Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Clear - -
Instrument Set-up Overview EN Display The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them.
Operations Switching ON/OFF ON EN Clear OFF i 2 sec Message Codes 1x Press ON button 2 sec to start continuous laser mode. Device is turned OFF. 2x Undo last action. If the message "InFo" appears with a number, observe the instructions in "Message Codes" section. Example: Leave actual function, go to default operation mode. Adjusting measuring reference i 1 Press button 2 sec and reference from front is set permanently. 2 Distance is measured from the front of the device.
Operations Beep ON/OFF EN Illumination ON/OFF 2 sec simultaneously Keypad lock ON 2 sec simultaneously Keypad lock OFF 2 1 2 sec simultaneously Leica DISTOTM E7300 788218a PRESS MINUS within 2 sec 4
Measuring Functions Measuring single distance 1 EN 2 i 3 8.532 m Aim active laser at target. Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or semi-permaeble surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time increases. Permament / Minimum-Maximum measuring min. 1 The minimum and maximum distance measured is displayed (min, max.). The last value measured is displayed in the main line. max.
Measuring Functions Area EN 1x 1 2 3 4 Aim laser at first target point. i 5 24.352 m Aim laser at second target point. 2 The result is shown in the main line and the measured value above. Partial Measurements: Press + or - after starting the first measurement. Measure and add or subtract distances. Finish with DIST. Measure 2nd length. Volume 2x 1 2 3 4 Aim laser at first target point. 5 6 Aim laser at second target point. Memory (last 10 results) 7 Aim laser at third target point.
Measuring Functions Pythagoras (2-point) EN 4x 1 2 3 4 Aim laser at upper point. i 5 8.294 m Aim laser rectangular at lower point. The result is shown in the main line and the measured distance above. Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement. Pythagoras (3-point) 5x 1 2 3 Aim laser at upper point. 5 Aim laser at rectangular point. i 7 4 6 Aim laser at lower point.
Measuring Functions Stake out EN 6x 1 2 1 2 3 3 1.000 m 4 Move device slowly along the stake-out line. The distance to the next stake out point is displayed. Leica DISTOTM E7300 788218a Adjust value. 0.625 m Approve value and start measurement. i 0.625 m 0.240 m When approaching a stake out point to less than 0.1 m the instrument starts to beep. The function can be stopped by pressing the CLEAR/OFF button. 0.240 m is missing up to next 0.625 m distance.
Technical Data Message Codes General Typical Measuring Tolerance* Maximum Measuring Tolerance** Range at Leica target plate GZM26 Typical Range* Range at unfavourable condition **** Smallest unit displayed Power Range Technology™ Laser class Laser type Ø laser point at distances Protection class Autom. laser switch off Autom. power switch-off Battery durability (2 x AAA) Dimension (H x D x W) Weight (with batteries) Temperature range: - Storage - Operation Functions ± 1.0 mm / ~1/16" *** ± 2.0 mm / 0.
Care Safety Instructions • Clean the device with a damp, soft cloth. • Never immerse the device in water. • Never use aggressive cleaning agents or solvents. The person responsible for the instrument must ensure that all users understand these directions and adhere to them. Disposal The symbols used have the following meanings: CAUTION Flat batteries must not be disposed of with household waste.
Safety Instructions EN Hazards in use Areas of responsibility WARNING Responsibilities of the manufacturer of the original equipment: Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Internet: www.disto.com The company above is responsible for supplying the product, including the User Manual in a completely safe condition. The company above is not responsible for third party accessories.
Safety Instructions FCC statement (applicable in U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems (ISO standard 9001) and Environmental Management Systems (ISO standard 14001). Total Quality Management - Our commitment to total customer satisfaction. Ask your local Leica Geosystems agent for more information about our TQM program. Copyright Leica Geosystems AG, Heerbrugg, Switzerland 2012 Original text (788218a EN) Pat.