Leica DISTOTM D1 The original laser distance meter
Overview 2 Technical data 3 Instrument Set-up 5 Operations 11 Message Codes 14 Care 15 Warranty 16 Safety instructions 17 Leica DISTO™ D1 1
Overview Ov e rv ie w The Leica DISTO™ is a laser distance meter operating with a class 2 laser. See chapter Technical data for scope of use.
Technical data T e c h n ic a ld a ta General Accuracy with favourable conditions * 2 mm / 0.08 in *** Accuracy with unfavourable conditions ** 3 mm / 1/8" *** Range with favourable conditions * 0.2 - 40 m / 0.6 - 120 ft *** Range with unfavourable conditions ** 0.2 - 30 m / 0.6 - 100 ft *** Smallest unit displayed 0.1 mm / 1/32 in Laser class 2 Laser type 635 nm, <1 mW ø laser point | at distances 6 /30 /60 mm | 10/ 50/ 100 m Protection class IP54 (dust- and splash water protected) Auto.
Technical data Functions Distance measuring yes Permanent measuring yes Beep yes Illuminated display yes Bluetooth® Smart yes Leica DISTO™ D1 4
Instrument Set-up In s tru me n tS e t-u p Introduction The safety instructions (see Safety Instructions) and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them.
Instrument Set-up Insert batteries To ensure a reliable use, we recommend using high quality Alkaline batteries. Change batteries when battery symbol is flashing.
Instrument Set-up Switching ON/OFF Device is turned OFF.
Instrument Set-up Clear Undo last action. Leica DISTO™ D1 Leave actual function, go to default operation mode.
Instrument Set-up Message Codes If the message "i" appears with a number, observe the instructions in Message Codes section.
Instrument Set-up Settings Press both keys simultaneousley. Switch between the following units: 0.000 m 0'00" 1/16 0.0000 m 0.000 in 0.
Operations Op e ra tio n s Measuring single distance surfaces the measuring time increases. Aim active laser at target. Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or permeable surfaces or when aiming at high gloss surfaces.
Operations Permanent measuring The last value measured is displayed in the main line. Leica DISTO™ D1 Stops permanent measuring.
Operations Bluetooth® Smart DISTO™ sketch. Use App for Bluetooth® data transfer. Bluetooth® Smart is always active when the device is switched on. Connect the device with your smart-phone, tablet, laptop.. Measurement values will be transferred automatically right after a measurement. The efficient and innovative Bluetooth® Smart module (with the new Bluetooth® standard V4.0) works together with all Bluetooth® Smart Ready Leica DISTO™ D1 devices.
Message Codes Me s s a g e Co d e s No. Cause Correction 204 Calculation error Perform measurement again. 220 Hardware error Contact your dealer 240 Data transfer error Connect device and repeat procedure 252 Temperature too high Let device cool down. 253 Temperature too low Warm device up. 255 Received signal too weak, measuring time too long Change target surface (e.g. white paper). 256 Received signal too high Change target surface (e.g. white paper) .
Care Ca re l Clean the device with a damp, soft cloth. l Never immerse the device in water. l Never use aggressive cleaning agents or solvents.
Warranty Wa ra n ty Warranty under PROTECT by Leica Geosystems Lifetime Manufacturer´s Warranty Warranty coverage for the entire usage time of the product under PROTECT according to Leica Geosystems International Limited Warranty and PROTECT General Terms & Conditions set out under www.leica-geosystems.com. Free of charge repair or replacement of all products or any parts under PROTECT that suffer defects as a result of faults in materials or workmanship.
Safety instructions Sa fe ty in s tru c tio n s The person responsible for the instrument must ensure that all users understand these directions and adhere to them.
Safety instructions Symbols used The symbols used have the following meanings: Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. WARNING Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
Safety instructions Permitted use l Measuring distances l Data transfer with Bluetooth® Leica DISTO™ D1 19
Safety instructions Prohibited use l Using the product without instruction l Using outside the stated limits l l l l l l l l Deactivation of safety systems and removal of explanatory and hazard labels Opening of the equipment by using tools (screwdrivers, etc.) Use of accessories from other manufacturers without express approval Carrying out modification or conversion of the product Deliberate dazzling of third parties; also in the dark Inadequate safeguards at the surveying site (e.g.
Safety instructions Hazards in use WARNING Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified. Carry out periodic test measurements. Particularly after the instrument has been subject to abnormal use, and before, during and after important measurements. CAUTION Never attempt to repair the product yourself. In case of damage, contact a local dealer.
Safety instructions Limits of use Refer to section Technical data. The device is designed for use in areas permanently habitable by humans. Do not use the product in explosion hazardous areas or in aggressive environments.
Safety instructions Areas of responsibility Responsibilities of the manufacturer of the original equipment: Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Internet: www.leica-geosystems.com The company above is responsible for supplying the product, including the User Manual in a completely safe condition. The company above is not responsible for third party accessories.
Safety instructions Disposal CAUTION Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations. The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Adhere to the national and country specific regulations.
Safety instructions Electromagnetic Compatibility (EMC) WARNING The device conforms to the most stringent requirements of the relevant standards and regulations. However, the possibility of causing interference in other devices cannot be totally excluded. Japanese Radio Law Compliance This device is granted pursuant to the Japanese Radio Law 電 波 法 . This device should not be modified otherwise the granted designation number will become invalid.
Safety instructions FCC statement (applicable in U.S.) This equipment has been tested and found to comply with the limits for a Class B digital instrument, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety instructions ISED Statement (applicable in Canada) This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: l l This device may not cause harmful interference, and this device must accept any interference, including interference that may cause undesired operation of the device.
Safety instructions Use of the product with Bluetooth® WARNING Electromagnetic radiation can cause disturbances in other equipment, in installations (e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals. Precautions: Although this product conforms to the most stringent standards and regulations, the possibility of harm to people and animals cannot be totally excluded.
Safety instructions Laser classification The device produces visible laser beams, which are emitted from the instrument: It is a Class 2 laser product in accordance with: l IEC60825-1 : 2014 „Radiation safety of laser products“ Pulse duration > 400 ps Pulse repetition frequency 320 MHz Beam divergence 0.16 x 0.6 mrad Laser Class 2 products: Do not stare into the laser beam or direct it towards other people unnecessarily.
Safety instructions Labelling Subject to change (drawings, descriptions and technical data) without prior notice.