Leica Zeno FLX100 plus Smart Antenna User Manual Version 1.
Introduction Congratulations on the purchase of the Leica Zeno FLX100 plus smart antenna. Purchase This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to 1 Safety Directions for further information. Read carefully through the User Manual before you switch on the product. The content of this document is subject to change without prior notice. Ensure that the product is used in accordance with the latest version of this document.
Name Description/Format Leica FLX100 plus smart antenna User Manual All instructions required in order to operate the product to a basic level are contained in the User Manual. Provides an overview of the product together with technical data and safety directions. – ü Refer to the myWorld web page for all Leica FLX100 plus smart antenna documentation/software: https://myworld.leica-geosystems.com • https://myworld.leica-geosystems.com offers a wide range of services, information and training material.
Service Description myDownloads Downloads of software, manuals, tools, training material and news for Leica Geosystems products.
Table of Contents 1 2 3 4 5 6 7 Safety Directions 6 1.1 1.2 1.3 1.4 1.5 6 7 7 7 8 General Introduction Definition of Use Limits of Use Responsibilities Hazards of Use Description of the System 13 2.1 2.2 2.3 13 14 15 General Information Instrument Components Accessories Operation 16 3.1 3.2 3.3 3.4 3.5 3.
1 Safety Directions 1.1 General Introduction Description The following directions enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid operational hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them. About warning messages Warning messages are an essential part of the safety concept of the instrument. They appear wherever hazards or hazardous situations can occur.
1.
Person responsible for the product The person responsible for the product has the following duties: To understand the safety instructions on the product and the instructions • in the User Manual To ensure that it is used in accordance with the instructions • To be familiar with local regulations relating to safety and accident pre• vention To stop operating the system and inform Leica Geosystems immediately if • the product and the application become unsafe To ensure that the national laws, regulations and
DANGER Risk of electrocution Because of the risk of electrocution, it is dangerous to use poles, levelling staffs and extensions in the vicinity of electrical installations such as power cables or electrical railways. Precautions: ▶ Keep at a safe distance from electrical installations. If it is essential to work in this environment, first contact the safety authorities responsible for the electrical installations and follow their instructions.
WARNING Inadequate securing of the working site This can lead to dangerous situations, for example in traffic, on building sites and at industrial installations. Precautions: ▶ Always ensure that the working site is adequately secured. ▶ Adhere to the regulations governing safety, accident prevention and road traffic. WARNING Improperly repaired equipment Risk of injuries to users and equipment destruction due to lack of repair knowledge.
For the AC/DC power supply and the battery charger: WARNING Unauthorised opening of the product Either of the following actions may cause you to receive an electric shock: Touching live components • Using the product after incorrect attempts were made to carry out repairs. • Precautions: ▶ Do not open the product! ▶ Only Leica Geosystems authorised service centres are entitled to repair these products.
CAUTION Before any cleaning procedure, ensure that the instrument is switched off and the battery has been removed. CAUTION Unused connectors must be protected using the attached dust cap.
2 Description of the System 2.1 General Information Design The instrument Four satellite-system (BeiDou, GPS, GLONASS, Galileo), support access to • external differential signal to get typical 2 cm (2D) positioning results FLX100 plus smart antenna with integrated helix antenna and Bluetooth • capability Small and lightweight, wearable • Low power consumption, long battery duration • Rubber bumper for drop protection • Is designed to be used on the pole or on the Universal Handheld Tray.
2.2 Instrument Components Description g a b c d e f 25020_001 a b c d e f g 14 Connection LED – blue when Bluetooth connected GNSS correction indicator – green when receiving correction data Satellite LED – green when position available Battery LED indicator – Green during normal operation – Red when power < 10% – Red when charging – Green when fully charged Power button to turn on/off the receiver Holes for the screws to fix the pole adapter USB-C port supports USB 2.
2.3 Accessories Operation with pole Pole setup. a b a c b c 25023_001 Operation with smartphone Leica FLX100 plus smart antenna AZ219 Pole Mount GLS30 Carbon Pole Using the AZ220 Universal Handheld Tray for FLX100 plus smart antenna. a b a c 25024_001 Operation with tablet b c Leica FLX100 plus smart antenna AZ220 Universal Handheld Tray Smartphone Using the AZ220/AZ225 Universal Handheld Tray for FLX100 plus smart antenna.
3 Operation 3.1 Power On/Off, Reset, Charging Description a a b b 25013_001 Power on/off button Battery LED indicator Function Description Power on/off Turn on: Press and hold the power button until all LEDs switch on. The device sounds a beep when ready for use. The device starts booting after the LEDs switch on. Once it is ready, the device sounds a beep. Turn off: Press and hold the power button until all LEDs switch off and the device sounds a long beep.
Setup with Universal Handheld Tray Use the Universal Handheld Tray to attach the FLX100 plus smart antenna with phone/tablet. The Universal Handheld Tray keeps the FLX100 plus smart antenna and phone/ tablet together. This setup maximises the productivity in the field. The Universal Handheld Tray has a spring-loaded frame to hold a phone/tablet of different sizes.
3.3 Phase Centre of the FLX100 plus Smart Antenna Phase centre The phase centre of the FLX100 plus smart antenna location is at the dot near the top of the device. Pole mode In pole mode, the offset from the phase centre to the top of the pole, including the pole adapter mount, is automatically accounted. Make sure to provide the appropriate antenna height in the software. Handheld mode In handheld mode, the location is measured at the dot. Make sure the FLX100 plus smart antenna is placed properly.
3.5 Configure Real-time Corrections Step-by-step This step-by-step procedure describes the configuration of the real-time correction in Zeno Mobile and Zeno Connect. RTK Profile Wizard 1. In Zeno Mobile 1. 2. Go to Settings within a project. Access GPS and then Realtime Corrections. In Zeno Connect 1. 2. Open the app and go to Settings. Go to Realtime Corrections. 2. Tap on + in the top-right corner of the screen to start the RTK profile wizard. 3. Enter profile details.
Further configuration Access again the Realtime Corrections menu to access the profiles. Modify any detail by tapping on the three dots next to the profile name. When position is available, activate/deactivate the automatic connection to the profile here. 3.6 Firmware Upload Step-by-step This step-by-step procedure describes how to upload the firmware on the FLX100 plus smart antenna. Download Firmware ☞ 1. The latest firmware is always available on myWorld. https://myworld.leica-geosystems.
4 Care and Transport CAUTION Unapproved chargers or cables Connecting the charger improperly may cause serious damage to the device. Any damage caused by misuse is not covered by the warranty. Unapproved chargers or cables can cause the battery to explode or damage the device. Precautions: ▶ Use only Leica-approved chargers, batteries, and cables. 4.1 Transport Transport in a road vehicle Never carry the product loose in a road vehicle, as it can be affected by shock and vibration.
4.3 Cleaning and Drying Product and accessories • Damp products Dry the product, the container, the foam inserts and the accessories at a temperature not greater than 40 °C/104 °F and clean them. Do not repack until everything is dry. Always close the container when using in the field. Use only a clean, soft, lint-free cloth for cleaning. If necessary, moisten the cloth with water or pure alcohol. Do not use other liquids; these may attack the polymer components.
5 Technical Data Instrument Positioning Type Description Satellites tracked GPS: L1C/A, L2C QZSS: L1C/A, L2C GLONASS: L1OF, L2OF BeiDou: B1I, B2I Galileo: E1B/C, E5b SBAS: WAAS, EGNOS, MSAS, GAGAN (L1 C/A) Channels 184 Update rate Up to 10 Hz Re-aquisition <2s RTK initialisation Typically > 120 s Cold start time Typically < 24 s Hot start Typically < 15 s Initialisation reliability > 99.9% Differential RTCM3.
Power Environmental specifications 5.1 Internal battery 3.8 V, 6120 mAh USB-C charging, supports 1.44 A fast charge Input voltage 5 V DC/2 A Power consumption < 1.5 W Working time > 20 hours Charge time Typically 4 hours Type Operating temperature [°C] Storage temperature [°C] Instrument −40 to +65 −40 to +80 External influences Protection Water, dust and sand IP67 Humidity Up to 100% (non-condensing) Shock resistance Designed to endure to a 2 m pole drop and 1.
GNSS frequency bands Type Frequency band [MHz] FLX100 plus smart antenna GPS, QZSS, SBAS: L1 1575.42 GPS, QZSS: L2 1227.60 GLONASS: L1 1602.5625-1611.5 GLONASS: L2 1246.4375-1254.3 Galileo: E1 1575.42 Galileo: E5b 1207.14 BeiDou: B1 1561.098 BeiDou: B2 1207.14 Frequency bands, output power Type Frequency band [MHz] Output power1) [dBm] Bluetooth 2402–2480 5.90 Bluetooth LE 2402–2480 1.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. • • • • Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user's authority to operate the equipment.
☞ Technical Data Damaged or defective batteries are prohibited from being carried or transported onboard any aircraft. Therefore, ensure that the condition of any battery is safe for transportation.
6 Leica FLX100 plus Smart Antenna Bundle 6.1 Standard Configuration Description The following table shows all parts for the standard configuration. Description Qty. Leica FLX100 plus smart antenna 1 Power adaptor with 4 plugs (US, UK, EU and AU) 1 Cable USB-C/USB-C, 1.5 m 1 Cable USB-C/USB-A, 1.5 m 1 AZ222 Arm/Belt pouch 1 Soft bag for Leica FLX100 plus smart antenna, black 1 Cardboard box 1 6.
The Pole is an optional accessory for the Leica FLX100 plus smart antenna. To use the Leica FLX100 plus smart antenna on a Pole, the appropriate adapter is required. This mounting allows customers to use the instrument vertically for precise and stable support. The Universal Handheld Tray is an optional accessory for the Leica FLX100 plus smart antenna. 6.
Part number, Package Description 6015970 FLX100 plus Pole Start package with Zeno Mobile Leica Zeno FLX100 plus smart antenna including: Multi-constellation support, • GPS, GLONASS, Galileo and BeiDou Power adapter • USB-C charging cable • USB-C/USB-A cable • Arm/Belt pouch arm bag • Softbag • Zeno Tab 2 Android tablet • Pole Mount Kit for Zeno Tab 2 • GLS30 GNSS telescopic carbon fibre pole • 5/8 pole mount to attach a FLX100 plus smart • antenna to a Leica GNSS pole Zeno Mobile Professional with 1-
7 Software Licence Agreement/Warranty International Limited Warranty This product is subject to the terms and conditions set out in the International Limited Warranty which you can download from the Leica Geosystems AG home page at Leica Warranty or collect from your Leica Geosystems AG distributor.
970060-1.0.0en Original text (970060-1.0.0en) Published in Switzerland, © 2022 Leica Geosystems AG Leica Geosystems AG Heinrich-Wild-Strasse 9435 Heerbrugg Switzerland www.leica-geosystems.
Specific Absorption Rate (SAR) information: This Smart Phone meets the government's requirements for exposure to radio waves. The guide lines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 0.
