Datasheet
Plug caps
B
L
ø A
N
Part number
BFG.00.100 PCSG
BFG.0B.100.PCSG
BFG.1B.100.PCSG
BFG.2B.100.PCSG
BFG.3B.100.PCSG
Note: this cap is available only with an alignment key (G). Upon request
this cap can be supplied in black and the last letter «G» of the part num-
ber should be replaced with «N».
Fitting the cord
Slide the plug into the loop of the cord.
Place the loop into the groove in front of the collet nut and
tighten the loop.
● Body material: Polyoxymethylene (POM) grey (or black)
● Cord material: Polyamide 6, grey (or black)
● Gasket material: Silicone rubber
● Maximum operating temperature: 100°C
● Watertightness: IP51 according to IEC 60529
BFG
Plug caps
L
B
sliding loop
ø A
N
BFA.0E.100.NAS
BFA.1E.100.NAS
BFA.2E.100.NAS
BFA.3E.100.NAS
BFA.4E.100.NAS
BFA.4S.100.NAS
BFA.5E.100.NAS
BFA.5S.100.NAS
BFA.6S.100.NAS
BFA
Dimensions (mm)
Series
ABLN
0E 14.0 6 12.5 85
1E 16.0 6 15.5 85
2E 19.5 6 17.5 85
3E 23.0 6 22.0 120
4E 29.0 10 22.5 120
4S 25.0 10 22.2 120
5E 44.0 10 27.0 150
5S 36.0 10 30.2 150
6S 46.0 10 33.0 150
● Body material: Nickel-plated brass (Ni 3µm)
● Lanyard material: Stainless steel
● Crimp ferrule material: Nickel-plated brass + polyolefin
● O-ring material: Silicone rubber or FPM
● Maximum operating temperature: 135°C
● Watertightness: IP68 according to IEC 60529 for E series
Note: the last letter «S» of the part number stands for the material of the O-
ring (silicone rubber). O-ring’s made from FPM are also available; if required,
replace the letter «S» by «V».
Part number
Dimensions (mm)
Series
ABLN
00 7.5 9.8 10.0 60
0S-0B 9.5 12.0 12.2 85
1S-1B
12.0 15.0 13.8 85
1D
2S-2B 15.0 18.0 15.0 85
3S-3B 18.5 22.0 18.5 95
136
www.lemo.com
®
®
Accessories
Plug caps with key (G)
L
B
sliding loop
ø A
N
BFG.0K.100.NAS
BFG.1K.100.NAS
BFG.2K.100.NAS
BFG.3K.100.NAS
BFG.4B.100.NAS
BFG.4K.100.NAS
BFG.5B.100.NAS
BFG.5K.100.NAS
BFG.6E.100.NAS
BFG
Dimensions (mm)
Series
ABLN
0K-0L 14.0 6 12.5 85
1K-1L 16.0 6 15.5 85
2K-2L 19.5 6 17.5 85
3K 23.0 6 22.0 120
4B 25.0 10 20.2 120
4K 29.0 10 22.5 120
5B 36.0 10 27.2 150
5K 44.0 10 27.0 150
6E 54.0 10 31.0 150
● Body material: Nickel-plated brass (Ni 3µm)
● Lanyard material: Stainless steel
● Crimp ferrule material: Nickel-plated brass + polyolefin
● O-ring material: Silicone rubber or FPM
● Maximum operating temperature: 135°C
● Watertightness: IP68 according to IEC 60529 for E and K series
Note: this cap is available only with an alignment key (G). The last letter
«S» of the part number stands for the material of the O-ring (silicone rubber).
O-ring’s made from FPM are also available; if required, replace the letter
«S» by «V».
Part number