Datasheet

149www.lemo.com
®
®
Part number
Supplier
LEMO
BALMAR
BUCHANAN
DPC.91.701.C
85230
621101
According to specification
MIL-C-22520/7-01.
For LEMO contacts ø 0.5-0.7-0.9-1.3 mm
Pneumatic crimping tools
DCE.91.050.0VC DCE.91.050.0VM
These positioners are suitable for use with both manual and
pneumatic crimping tools according to the MIL-C-22520/7-01
standard.
Connector + Contact
Conductor
Type
AWG
302
303 0.5 0.45 1 28-30-32
304
Positioners part number
For male For female
contact contact
Positioners for crimp contacts ø 0.5-0.7-0.9 and 1.3 mm
DCE
male female
00
DCE.91.090.BVC DCE.91.090.BVM
DCE.91.090.AVC DCE.91.090.AVM
DCE.91.070.BVC DCE.91.070.BVM
DCE.91.050.BVC DCE.91.050.BVM
0.9 1.10 1 20-22-24
0.9 0.80 2 22-24-26
0.9 0.45 2 28-30-32
0.7 0.80 1 22-24-26
0.7 0.45 2 28-30-32
306/307
0.5 0.45 1 28-30-32
309
0B
0K
0S
DCE.91.131.BVC DCE.91.131.BVM
DCE.91.091.BVC DCE.91.091.BVM
DCE.91.071.BVC DCE.91.071.BVM
DCE.91.051.BVC DCE.91.051.BVM
1.3 1.40 1 18-20
1.3 1.10 2 20-22-24
0.9 1.10 1 20-22-24
0.9 0.80 2 22-24-26
0.7 0.80 1 22-24-26
0.7 0.45 2 28-30-32
310/314
0.5 0.45 1 28-30-32
316
306/307
308
1B
1K
1S
DCE.91.132.BVC DCE.91.132.BVM
DCE.91.132.CVC DCE.91.132.CVM
DCE.91.092.BVC DCE.91.092.BVM
DCE.91.092.AVC DCE.91.092.AVM
DCE.91.072.BVC DCE.91.072.BVM
1.3 1.40 1 18-20
1.3 1.10 2 20-22-24
1.3 0.80 2 22-24-26
0.9 1.10 1 20-22-24
308/310 0.9 0.80 2 22-24-26
0.9 0.45 2 28-30-32
0.7 0.80 1 22-24-26
0.7 0.45 2 28-30-32
2B
2K
2S
Note: see table on page 51 for connector selection and the table
on page 131 for contact selection.
Note:
1)
only these types are available in S series.
Supplier
LEMO
DANIELS
ASTRO
DPC.91.701.V
1)
DPC.91.101.A
2)
DPC.91.102.V
MH860
1)
AF8
2)
M300BT
616336
1)
615708
2)
–
1)
According to specification MIL-C-22520/7-01.
2)
According to specification MIL-C-22520/1-01.
Manual crimping tools
Part number
contact ø 0.5-0.7 contact ø 1.6-2.0 contact ø 3.0-4.0
0.9-1.3 (Fig. A) (Fig. B) (Fig. B)
ø A
ø A
ø C
ø C
Fig. 1
ø A
ø C
ø A
ø C
Fig. 2
ø A ø C Fig.
Note: a wide variation of strand number and diameter com-
binations are quoted as being AWG, some of which do not have
a large enough cross section to guarantee a crimp as per
either MIL-C-22520/1-01 or /7-01. Our technical department is
at your disposal to study and propose a solution to all your appli-
cations.
312/314
316/318
319
Fig. A
Fig. B
302
1)
303
304
1)
305
302
1)
303
304/305
306
1)
307
304
1)
305
Crimping tools for electrical contacts