MDV-6 Home Cinema Set FOREWORD
THANKS Thank you for purchasing this product! Your choice of the product sufficiently displays your expertise in acoustic equipment. We are honored to provide you with more satisfactory products.
FOREWORD…………………………………………………………………………………….2 CONTENT………………………………………………………………………………………..3 WARNING……..……………………………………………………………………………...….3 FRONT PANEL...………………………………………………………………………………..4 BACK PANEL……………………………………………………………………………………5 REMOTE CONTROL……………………………………………………………………………6 CONNTECTION WITH TV……………………………………………………………………...7 CONNECTION WITH AMPLIFIER…………………………………………………………….8 SYSTEM CONNECTION……………………………………………………………………….9 BASIC OPERATION………………………………………………………………………..10-16 DVD MENU SETUP…..
8.. DISPLAY SCREEN 9. FAST REWIND/FAST FORWARD (TUNE-/+) BUTTON 10. VOLUME+/11. PREVIOUS/NEXT(CH-/+) BUTTON 12. FM BUTTON、SEARCH BUTTON 13. DVD BUTTON、SAVE BUTTON 1. REMOTE CONTROL SENSOR 2. POWER ON/OFF BUTTON 3. STOP BUTTON 4. DISC DOOR 5. EJECT BUTTON 6. AUDIO BUTTON、MONO/STEREO BUTTON 7.
BACK PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
REMOTE CONTROL NOTE: 1. Place the batteries in the remote control and turn on the player, put the emitter against the sensor of player for remote control. 2. The distance of remote control should not exceed 7 meters, or else, it will be invalid. 3. If the sensor or remote control emitter is stuck with foreign matters, it may result in the malfunction in signal reception or not at all. 4.
CONNECTION WITH TV 1. If you TV has AV terminal, connect this unit to TV with A/V cables, and set TV to be AV status 2. If your TV has S-Video terminal, please use the S-Video connection cable to connect the player 3. If your TV has chromatics output terminal, please use three connection cables to connect the 4. This unit has an output interface for SCART output, which can directly be connected with TV. after confirming the connection is correct. (Figure 1) and TV, to obtain a higher quality image.
CONNECTION WITH AMPLIFIER Setup of Digital Audio Output Connect the optical or coaxial output jack to the amplifier. While in of play or stop mode, press the setup button on the remote control to open the system setup page, switch to audio setup page by pressing the directional buttons, then move the cursor to Audio Out, select SPDIF/RAW or SPDIF/PCM, press Play/Enter button to finish. Press setup button again to exit the setup.
SYSTEM CONNECTION Please refer to the following figure to connect your acoustic equipment! To keep all the connection correctly and firmly! Power supply can be connected finally.
BASIC OPERATION PREPARATIVE 1). Before turning on, check whether all the connection are correct and reliable. Plug the power plug into the corresponding power socket. 2). Press Power button on the front panel to turn on. 3). Press Eject button on the remote control or panel to carry the disc tray outside, put the disc into the tray, press Eject button again, this unit starts to read and play.
BASIC OPERATION TIME SELECTION In play mode, press T/F button on the remote control, the TV screen displays, VCD Display: VCD TRK 01/XX VCD Display: DVD TT 01/XX PBC 00:00:00 CH 007/XXX 00:00:00 You can press ◄ ► directional buttons to move the cursor to the time position, then input the corresponding numbers by pressing the numeric buttons, then press Play/Enter button to enter the desired part for playing. The optional time range depends on the volume of the played disc.
BASIC OPERATION SHORTCUT When play DVD discs, press the Shortcut button to jump over the initial title, menu or warnings. (Only for some discs, subject to the quality or recorded status of the played discs) SOUND FIELD In play status, press S.Field button, you can select different sound field effect. Note: While in DVD playing, this function is invalid. RESET In any status, press Reset button can return the original setup or default value.
BASIC OPERATION NUMBER BUTTONS 1). While playing songs, press the numeric buttons to directly select the songs you need. 2). If the desired track number is # 10 or above, you can select it by pressing the 10+ button once, and then pressing a numeric button (1--10). For example: If the 16th song is needed, you can press the 10+ button followed by the 6. PROGRESSIVE SCAN/INTERLACE Press the INT./P.SCAN button to switch four video output modes: INTERLACE-YUV, TV-RGB, P-SCAN YPBPR, S-VIDEO.
BASIC OPERATION SLOW In play status, every time the Slow button is pressed, the speed of the disc will play in 1/2,1/3,1/4,1/5,1/6,1/7. MP3 DISC PLAYING FUNCTION 1). Press the Eject button on the panel or remote control to open the deck, put in an MP3 disc, then press the Eject button to close the deck. This unit begins to read it , and the TV screen will display the following figure, Play file selection area Contents Area 2).
BASIC OPERATION MPEG4、JPEG PICTURE DISC PLAYING FUNCTION 1). Place the MPEG4/JPEG disc into the deck, this unit will begin to read, the main directory will be displayed on the TV screen. Play File Selection Area Directory Area 2). Press the direction button ▲▼ to move the cursor to the corresponding directory, press Play/Enter button to enter the next layer, and so on, until the desired picture is found for play. During play, number buttons or button can be used to select pictures.
BASIC OPERATION FM RADIO OPERATION 1. Enter FM Function In the turn-on or play status, press the FM button on the remote control, enter FM status. 2. Select Bands 1) directly input frequency: press the T/F button on the remote control, input the frequency that 2) Select band by pressing Tune- or Tune+ button: under some frequency, press the button, the you want directly. frequency will be up or down on the step. The step of FM is 0.05 MHz .
DVD Menu Setting Press the Setup button on the remote control to open the menu setup function, the TV screen will display the following figures. 1. SYSTEM SETUP PAGE 1). TV System Perform adjustment according to different disc applicable for different TV systems, includes four options: NTSC, PAL, PAL60, AUTO. 2). Screen Saver This option is used to open or close screen saver program, includes: ON and OFF. 3). Video Output According to your requirement, you can input different video source.
DVD Menu Setting 5). Password and Rating The password is used to prevent the children watching unproper discs. (1) Input a four-digit password. (The initial password of this unit is 0000.) (2) Move the cursor to rating option, press Play/Enter button to select the desired rating. (3) Press the direction buttons to exit. Note: You can not play the discs with a rating higher than your set rating, unless input the correct password upon the system prompt.
DVD Menu Setting 3.AUDIO SETUP PAGE 1). Audio Out Each DVD disc has various audio output types for selection. You can set the type according to the acoustic system type you are using. Three options are available: SPDIF/OFF: no signal output from either coaxial or optical output port SPDIF/RAW: this option is chosen when the coaxial and optical port is connected with power amplifier.
DVD Menu Setting 4.VIDEO SETUP PAGE 1). Brightness This option is used to change the brightness of the screen, press the up/down direction button to adjust the brightness, press left direction button to exit. 2). Contrast This option is used to change the contrast of the screen, press the up/down direction button to adjust the contrast, press left direction button to exit. 3).
DVD Menu Setting 5. DIGITAL SETUP PAGE 1). OP Mode (1) Line Output : to compress the input signal linearly, lower in volume and applicable to night. (2) RF Remod: no compression for the input signal, higher volume and applicable to day. 2). Dynamic Range When the output mode is Line Output, this unit will automatically adjust the linear compression ratio to acquire different compression effect of signals.
SPECIFICATION DVD Disc Type MP3 CD PLAYBACK Video Format MPEG 2 for DVD, MPEG 1 for VCD Audio Format MPEG 1, MPEG 2, PCM, STEREO Video system: NTSC, PAL, PAL60, AUTO Signal Output Video output 1.0 V p-p Audio: stereo Chromatic aberration output, S-Video output, Stereo, Output Joint Video output, Optical Fiber output, Coaxial output and Scart output Power Supply AC220V 50Hz Max.
TROUBLESHOOTING Please use the following methods to solve the following problems while using this unit.