CS 172 BT OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • RDS (Radio Data System) Operation • Digital Compact Disc Player • Bluetooth Function • Automatic Memory Storing • Fold Down Full Detachable Panel • Preset Equalization • Remote Control
CONTENTS Selecting tracks in single step .........14 Selecting directory up/down ............14 Pausing playing................................14 Previewing all tracks ........................14 Repeating the same track ................14 Playing all tracks in random .............14 Selecting tracks by AS/PS(MP3) button ..........................14 Display information ..........................15 Disc notes ...........................................26 Bluetooth operation .........................
INSTALLATION Notes: TAKE OUT SCREW BEFORE INSTALLATION • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before install the unit, please remove the two screws. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Take out screw before installation • Use only the parts included with the unit to ensure proper installation.
INSTALLATION Sleeve Spring Washer L Key Outer Trim Ring Front Panel Hex Nut Metal Strap Mounting Bolt Plain Washer Tapping Screw R Key 6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. 10.
INSTALLATION DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Side view showing Screw Holes marked T, N Screw Factory Radio Mounting Bracket Hook Screw Hook Dashboard or Console To fasten the unit to the factory radio mounting brackets. 1.
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel To Reinstall the Front Panel 1. Press the OPEN button, then the front panel will be folded down. 1. When the metal plate is folded down, insert the front panel into the metal plate then push them into the main body. A ‘click’ sound will be heard. Open 2. Remove the front panel by pulling its middle-hand side outward. 2.
WIRING CONNECTION MAIN UNIT BLUETOOTH SOCKET COMMANDER BLUETOOTH ANTENNA ANTENNA CONNECTOR IGNITION SWITCH (ACC+) MEMORY BACK-UP (B+) GROUND (B–) POWER ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER RED YELLOW (GREY) BLACK REAR RCA CABLE Rch RED Lch WHITE BLUE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 7 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION LOCATION OF KEYS 17 7 11 10 16 12 13 15 18 8 19 20 21 14 22 5 8 25 23 1 24 6 4 26 27 9 3 2
OPERATION (ALARM) is output. When newly tuned station does not have TP information for several seconds, beeps come out. When TP information gets lost at the current station for retune time, the beep sound is out-putted. When newly tuned station has not RDS signal, “PI SEEK” is suppressed somewhat. SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except OPEN button (7) and EJECT button (4)). When system is on, press button (9) to turn off the unit.
OPERATION (11) or MULTI JOG ( ) button (12). retune time, the radio start to retune to next same PI station. When same PI station does not catch 1 cyclic search, the radio goes to last station and waits for several minutes until PI code is received. - BEEP 2’nd mode: The beep is only generated when all allowed double key is pressed long (1 sec). e.g. When preset button (14) is pressed. When BND/LOU button (13) is pressed. When AS/PS button (18) is pressed.
OPERATION EQUALIZATION Press P-EQ button (25) to turn on equalization function and to select desired audio mode. There are five kinds of mode as below: FLAT CLASSICS POP M ROCK M At radio mode, press BND/LOU button (13) shortly to select the desired band. The reception band will change in the following order: FM1 DSP OFF FM2 FM3 MW • SELECTING STATION button (16) Press SKIP/MANU or SKIP/MANU button (17) shortly to activate automatic seek function.
OPERATION • RDS (RADIO DATA SYSTEM) OPERATION - Setting RDS Mode Press AF/REG button (3) and release immediately to switch on or off RDS mode. Whenever RDS is switched on, symbol “AF” appears on the display. Program name is displayed on receiving a RDS station. “AF” starts blinking if the broadcasting signal getting worse.
OPERATION EON: Enhanced Other Networks Information Broadcasting information on PI, AF, TP, TA, etc. relating to networks other than the network used for current reception PTY: Program Type Code Contents of programs such as news, light music, sports etc. unwanted EON TA switching, which EON TA information was received from current station and the radio switched to that EON linked station, but no information could not be received because the EON linked station is located too far from that area.
OPERATION • PLAYING ALL TRACKS IN RANDOM Press SHF button (22) to play all tracks on CD in random order. Press again to cancel the function. • PLAYING ALL TRACKS IN RANDOM Press SHF button (22) to play all tracks on MP3 disc in random order. Press again to cancel the function. • EJECTING A DISC Press EJECT button (4) to stop CD playing and eject the disc from the disc slot (5). • SELECTING TRACKS BY AS/PS(MP3) BUTTON AS/PS button is assigned as Digital Audio Mode selection button in MP3 operation.
OPERATION - - - name is displayed for a second and the currently playing file name is displayed (selected). The user can select the directory or file in the directory by MANU/SKIP UP/DOWN buttons. The selected file can be played by pressing BND/LOU (ENTER) button. entry of each characters. Press BND/LOU (ENTER) button to start the title search.
OPERATION KEY Assigned IN Searching mode (Table 1) AP/AS Mode Select BND/LOU ENTER M1 A, B, C, 1 M2 D, E, F, 2 M3 G, H, I, 3 M4 J, K, L, 4 M5 M, N, O, 5/ Directory DOWN M6 P, Q, R, 6/ Directory UP MODE S, T, U, 7 B. Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs): 1. Be sure to use discs with following marks only for the unit to play: Recordable 2. The unit cannot play a CD-R and CD-RW that is not finalized.
OPERATION BLUETOOTH OPERATION 6 5 3 1. PAIR button 2. LED indicator 3. TALK button 4 1 2 4. Internal microphone 5. To the main unit 6. External microphone jack TYPE A: BLUETOOTH HANDSFREE PROFILE SETUP a. Press PAIR button (1) about 4 seconds, the LED indicator twinkle rapidly, and it enters into Handsfree pair mode; if click PAIR button (1) about 1.5 seconds, secede from pair mode. b.
OPERATION MICROPHONE You can talk toward the microphone (4). If you are not near the commander, you can connect another microphone through the external microphone jack (6). TYPE B: BLUETOOTH HEADSET PROFILE SETUP a. Press PAIR button (1) about 4 seconds, the LED indicator twinkle rapidly, PAIR button (1), the LED twinkles slow, and it enters into Headset pair mode; if click PAIR button (1) about 1.5 seconds, secede from pair mode. b.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) : DC 12 Volts, Negative Ground : 178 (W) x 165 (D) x 50 (H) mm : ± 10 dB : ± 10 dB Maximum Output Power Current Drain : 4 x 40 Watts : 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 45 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 108 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. No sound. Sound skips. The operation keys do not work. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse.