7,5 cm (7”) portable dvd player USER'S MANUAL DVP-738X2 For information and support,WWW.lenco.eu Before connecting, operating or adjusting this product, please read this user's manual carefully and completely.
Table of Content Contents SETUP Menu Setting Table of Contents 1 Important Safety Instructions 2 Safety Precautions 3 Video Setup Page Basic Operation 4 Preference Page General Page Audio Setup Page Identification of Controls Main Unit Remote control unit 8 8-9 9 9-10 Password Setup Page 10 Battery Parameters 11 Parameters and specifications 11 5-7 5 6-7 Dear Customer: Thank you for purchasing this Portable DVD player with swivel screen & USB/SD.
Important Safety Instructions Warning: To reduce the risk of electric shock, do not remove the cover or back. There are no user-serviceable parts inside. Refer servicing to qualified personnel. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Warning: To prevent fire or electric shock hazard, do not expose the unit to rain or moisture.
Safety Precautions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN Warning: This digital video disc player employs a laser system. Use of controls,adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation Exposure. Warning: To prevent direct exposure to laser beam,do not open the enclosure.Visible laser radiation when open. Warning: Never stare directly into the laser beam.
Mounting in the Vehicle Use the supplied car mounting straps to install the main unit and monitor on the back of the vehicle's headrests.Tightly wrap the mounting strap around the headrest. Please kindly note that Unit A corresponds with Remote control A and Unit B corresponds with Remote control B.
Identification of Controls Main Unit 1.SD/MS/MMC 2. POWER ON/OFF 3. HEADPHONE OUT JACKS 1 4. VIDEO/AUDIO OUT 5. DIGITAL AUDIO OUT (COAXIAL) 6.USB 2 3 7. DC IN 9-12V 4 5 8. ENTER 9. UP/DOWN/LEFT/RIGHT 9 6 10. SOURCE 7 8 10 Insert the battery 1.Open the battery door. 2.Insert battery. When using the remote control for the first time do not forget to remove the plastic card. N 5 NOTES: Remove battery during storage or when you are not using the DVD player for a long time.
Identification of Controls Remote control unit 17 16 STEP 1 19 2 8 9 0 10+ DISPLAY SUBTITLE 20 TITLE 26 4 7 AUDIO ENTER 22 27 3 6 21 25 SOURCE 5 18 24 MUTE 2 3 4 MENU /PBC 6 8 10 MODE VOL- REPEAT 1 5.10+ BUTTON In order to select a track 10 or greater, first press 10+, For example; select track 12, first press 10+, and then press number 2 button. 11 VOL+ 12 SLOW ZOOM 14 15 5 7 9 23 13 6. MENU/PBC Return to DVD root menu(DVD). PBC on/off switch (VCD) . 7.
Identification of Controls Remote control unit 15. BUTTON Press BUTTON allow skipping back at 5-level speed(X2->X4-> X8->X16->X32 -> PLAY), press PLAY button return to normal playback. 16.STEP Step the motion in DVD mode. 17.SEARCH Goto time point , title or chapter you want in DVD Mode. 18.SUBTITLE Press SUBTITLE repeatedly during playback to hear a different subtitle languages. 19.ANGLE DVD :Press ANGLE will change the view angle, on DVDs that support this feature. 20.TITLE Return to DVD title menu 21.
SETUP Menu Setting General Setup Page Press SETUP button to get the setup menu. Use direction buttons to select the preferred item. After finishing settings, press SETUP again to normal display.
SETUP Menu Setting Audio Setup Page Downmix This options allows you to set the stereo analog output of your DVD Player. Video Setup Page Video Setup Page - - VIDEO SETUP PAGE - - LT/RT :Select this option if your DVD Player is connected to a Dolby Pro Logic decoder. Stereo :Select this option when output delivers sound from only the two front speakers. Digital Output The function is used to select the SPDIF Output:SPDIF Off,SPDIF /RAW,SPDIF/PCM. SPDIF Off: Turns off the SPDIF output.
SETUP Menu Setting Password Setup Page Preference Page Password: select the menu password change page. PAL - Select this if the connected TV is PAL system.It will change the video signal of a NTSC disc and output in PAL format. NTSC-Select this if the connected TV is NTSC system.It will change the video signal of a PAL disc and output in NTSC format. Auto:Chang the video signal output automatic according to the playing disk format.
Parameters and specifications Battery Parameters Electronical parameters Battery Parameters Standard requirement Item Power requirements : AC 100-240 V , 50/60 Hz Power consumption : <15W Operating humidity : 5 % to 90 % Output VIDEO OUT AUDIO OUT :1.