22” (55.5cm) Full HD LED TV WITH DVB-S Model No.: LED-2213 For information and support, www.lenco.
Contents 1-3 SAFETY INFORMATION 4 5-6 7 8-11 12 13 14-21 Unit Remote Control Aerial connection Connecting external devices Auto installation setup Source menu Menu settings 21-35 DVBS Operation 36 37 TROUBLE SHOOTING GUIDE TECHNICAL SPECIFICATIONS options
SAFETY INFORMATION IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE. Take note of the following safety information which appears on the back of the TV. CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVER SCREWS, NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that there are important operating maintenance instructions in the literature accompanying this unit.
IMPORTANT SAFETY INFORMATION (Continued) This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. x Although this appliance has been carefully manufactured and rigorously checked prior leaving the factory, as with all electrical appliances it is possible for problems to develop.
IMPORTANT SAFETY INFORMATION (continued) Liquids spilt into the unit can cause serious damage. Switch the set OFF and disconnect the mains power supply, then consult a qualified service person before attempting to use the unit again. Do NOT remove the safety covers. There are no useable or serviceable parts inside. You may invalidate the warranty. Qualified personnel must only service this apperatus. Do NOT tap or shake the screen, you may damage the internal circuits.
Unit and Accessories LED Indicator Remote Control Window (keep clear) The functions of the TV buttons are described below. MENU: Press to display the OSD menu, Press again to exit the menu. CH-/CH+: Press to scan through channels. They are also can be used to move down/up in the OSD menu screen. VOL-/VOL+: Press to adjust the volume. They are also can be used to move left/right in the OSD menu screen. VOL+ button can be used to skip forward to next menu. INPUT: Press to select the source.
Remote control POWER: Turn the TV on/standby. MENU INPUT Buttons for TELETEXT(In ATV mode) TV/TXT: Teletext on/off CANCEL: Turn off the Teletext display REVEAL: Reveal any hidden text, for example-quiz answer NICAM/A2 HOLD: Hold or carry on the current subpage SIZE: Press to see top half of page double size, Press again to see the bottom half of page double size, Press again for normal size SUBPAGE: press to subpage, again to cancel. INDEX: go to index.
Remote control (continued) MENU INPUT EXIT USB DISPLAY TV/RADIO DVBS-SAT DVBS-AUDIO DVBS-INFO FAV SUBTITLE TEXT PAUSE EPG PIC-FORMAT PICTURE: Select the picture mode. SOUND: Select the sound mode. DISPLAY: Display current mode information. MUTE: Mutes the Audio. SLEEP: Standby Timer. TV/RADIO: Disc menu change between TV and Radio. DVBS-SAT: Display the satellite list. DVBS-AUDIO: Shows the list of available languages for the channel you are watching.
Aerial connection USER GUIDE WARNING! ENSURE THE TV AND ALL ANCILLARY EQUIPMENT IS UNPLUGGED FROM THE MAINS BEFORE MAKING ANY CONNECTIONS! Connecting the TV Antenna Connect the TV antenna to the aerial socket with a 75 ohm co-axial plug. For best results use a high gain TV aerial, preferably roof or loft mounted. • To improve picture quality in a poor signal area, purchase and install a signal amplifier. • If the antenna needs to be split for two TVs, use a 2-Way Signal Splitter (not supplied).
Connecting external devices (continued) SCART POWER: Connect to the mains adaptor. HDMI: Connect it to the HDMI of DVD or other equipment. VGA: For PC display.Connect it to the D-Sub 15 pins analog output connector of the PC. PC-IN: Connect it to the audio output terminal of PC. SCART: Connect them to the SCART video output terminal of DVD.(used in component source) Headphone: Connect it to your headphone or other audio equipment. RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal.
Connecting external devices (continued) PC connection As PCs are sometimes still supplied with a ‘conventional’ CRT monitor, you may need to adjust the display settings of your PCs graphics card, otherwise the pictures may not appear correctly. Switch on your PC (still with your original monitor connected) no w select the screen resolution, and select 60Hz refresh rate. Switch off your PC, then connec t it to your TV while both appliances are still switched off.
Connecting external devices (continued) Connecting Video camera and Video recorder Video camera x x x x Connect the AV cable to the TV and to the video camera. Turn on both video camera and the TV. Select AV/CVBS source You can now see the playback picture from the video camera. Note: x To connect the video camera using other cables, refer to the video camera instruction manual. Video recorder x x x x Connect the Scart cable to the TV and video recorder.
Connecting external devices (continued) Connecting an audio system You can supply the TV sound to the stereo system (A) with the Scart socket. Use a special scart cable SCART to RCA. (Please consult your hi-fi instructions for details). If you have a surround sound amplifier/decoder (B) Use the Scart cable or the special scart cable Scart to RCA.
Auto installation setup Power On / Off the LCD TV 1. Connect to the power supply with a power code and an adaptor. 2. -To turn on the TV Press POWER button on the TV or remote control. -To turn off the TV Press POWER button on the TV or remote control. When you initially turn on the LCD TV you will see the first time installation menu as below: Ensure that the aerial is plugged in to the TV, Make sure your Remote is in TV mode (by pressing INPUT button), switch on the TV by pressing POWER.
Bas c Use Menu Settings 1. Turn the LCD TV on. 2. Press the MENU button on the Remote Control. 3. Use the and buttons to navigate through the menu. 4. Press the EXIT button to exit the Menu. CHANNEL MENU Allows you to search channels and set up a variety of channel options. SETTING MENU: Allows you to setup a variety of setup options. Allows you to customize the sound options and effects. FUNCTION MENU: Allows you to set up a variety of lock/time and setup options.
Application Menu Settings (continued) Use the and buttons to select the CHANNEL menu (as the picture above), press button to enter the menu. The CHANNEL menu includes the following options : Country Press and buttons to select the Country. (Can be selected in ATV mode) Auto Search Press button to start auto search. Auto Search menu for ATV Manual Program Press button to enter the submenu. Manual Program menu for ATV Program Color Sys. Sound Sys.
Program Edit: Press button to enter the submenu as the following picture. Program Edit menu for ATV FAV NAME: Select the channel, press GREEN button on the remote control to change the name of the channel. (Use button to name, and press OK button to confirm) LOCK: Select the channel, press RED button to lock the channel. You have to enter the code to view the channel you have locked. Note: you could set the code in System Lock menu in FUNCTION menu, the original code is 0000.
Menu Settings (continued) Use the and buttons to select the PICTURE menu (as the picture above), press button to enter the menu. Picture Mode Choose from Standard, Movie, Vivid and Personal. Note: Contrast, Brightness, Color and Sharpness can only be adjusted in the Personal mode option in the Picture Mode Settings. Contrast Controls the difference between the brightest and darkest regions of the picture. Brightness Controls the overall brightness of the picture Color Control the color.
Application Menu Settings (continued) Use the and buttons to select the SOUND menu (as the picture above), press button to enter the menu. Sound Mode Allows you to select among: Standard, Music, Movie and Personal. Bass (Can be adjusted when the sound mode is set to User) Controls the relative intensity of lower pitched sounds. Treble (Can be adjusted when the sound mode is set to User) Controls the relative intensity of higher pitched sounds.
Menu Settings (continued) Use the and buttons to select the SETTING menu (as the picture above), press button to enter the menu. The SETTING menu includes the following options: Language Allows you to select menu language. OSD Timer Allows you to select the time for OSD menu displays on the screen. Transparence Allows you to select the transparence for OSD menu displays on the screen. Overscan Turn on/off the overscan funciton.
Menu Settings (continued) Use the and buttons to select the FUNCTION menu (as the picture above), press button to enter the menu. The FUNCTION menu includes the following options : Sleep Timer Allows you to setup the sleep timer to : 15min, 30min, 45min, 60min, 75min, 90min,105min, 120min and off. Aspect Allows you to select the screen display mode. (Can be selected in DTV mode) TT Language Allows you to select the Teletext language.
Menu Settings (continued) Use the and buttons to select the PC SETUP menu (as the picture above), press button to enter the menu. The PC SETUP menu includes the following options : H-Position Adjust the transverse position of the screen. V-Position Adjust the vertical position of the screen. Clock Adjust the pixel clock frequency, until the image size is maximized for the screen. Phase Adjust the phase of the ADC sampling clock relative to the sync signal, until a stable image is obtained.
DVBS Operation 1 Main Menu All the important settings and features of your receiver can be operated in Main Menu. The Main Menu consists of four sub-menus which are "Installation", “System setting”, "Channel Organizer" and "Multimedia". Press the MENU key when the menu is off, The MAIN MENU screen will appear 1.1 Installation The installation menu contains three sub-menus; “Dish Setup”, “Auto Scan” and “Transponder Manager”. 1.1.
1.1.1.2 Transponder You can select the current Transponder or add the new Transponder. 1.1.1.3 Local Frequency You can change the local frequency. Note: You must press OK to save this local frequency when the cursor is on the Local Frequency item before you select another satellite. 1.1.1.4 22K Tone You can change the 22k tone. Press LEFT/RIGHT select ON, OFF or AUTO. Note: You must press OK to save this 22K tone when the cursor is on the 22K Tone item before you select another satellite. 1.1.1.
Move the curser to Back or Next button and press OK to exit the submenu to the last menu. When you select DiSEqC1.2: Press OK to enter the submenu of the Adjust Antenna. Press UP/DOWN to move the curser to the item of the Transponder. Press LEFT/RIGHT to select the current transponder. Press UP/DOWN to move the curser to the item of the Move Dish. Press LEFT/RIGHT to move dish. Press UP/DOWN to move the curser to the item of the Goto Ref.. Press OK to go to 0.
1.1.2 Auto Scan Press UP/DOWN key to move the curser to the satellite you want to select, and press OK to mark or unmark. Press the RED button to scan all channel of the marked satellite. Press the GREEN button to Blind Scan the marked satellite. Press the YELLOW button to scan free channel of the marked satellite. 1.1.3 Transponder Manager In this menu, you can add, edit, and delete the transponder. you can search transponder. 1.1.3.1 Satellite You can select the satellite. 1.1.3.
1.1.3.3 Polarity You can select the polarity. 1.1.3.4 Symbeol Rate You can select Symbol Rate. 1.1.3.5 NIT Searching You can select the NIT Searching. 1.1.3.6 Free You can select the free mode. . 1.2 System setting In this menu, you can configure the systems such as language Setting, OSD style, Parental Control, TV Settings, Time Setting and System Update. 1.2.
1.2.1.5 Time Setting Press OK go to Time Setting below: If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. If the GMT usage is ON then the Current time is set automatically or you can set the time zone. If your broadcaster provides the correct time offset then your receiver will change from summertime to wintertime automatically. If you set GMT Usage to OFF, Set Data and Set Time item are displayed.
● Change PIN Modifying the PIN. You must enter the 4 digits PIN and confirm it again; the system PIN will be changed into the new PIN as show on. 1.2.3 System Update In this menu, you can select “Update by OTA”, “Update by DEV ” ● Update by DVBS You can update your STB software by USB. Select “System Update – Update by DEV”, you can select update software from USB disk, and press OK key to update your DVBS.
1.2.4 System info The system information displays information about your receiver such as software hardware and date. 1.2.5 Timer You can set the timer to make the receiver perform designated actions. Use the UP/DOWN buttons to select timer. Press the LEFT/RIGHT key to activate/inactivate current timer. Press the OK button to enter your selected timer settings.
1.3 Channel Organizer In the MAIN MENU screen, press UP/DOWN to move the cursor to Channel Organiser, and then press OK to enter the Channel Organizer menu. The Channel Organizer menu consists of three sub-menus; “Channel Manager” , “Favorites Manager” , “Remove Satellite” . 1.3.1 Channel Manager In this menu, you can change the order of the channels, delete and edit channels. To change the satellite use the RED button, and press Left/Right button.
Edit (YELLOW button) Select the channel that you wish to edit, press the YELLOW (Edit) button to move into the modify program menu. In this menu, you can modify the Program Name, Frequency, Symbol rate, Video PID, Audio PID. If you want to rename the channel, use the UP/DOWN keys to select “program Name” and press OK, the program name dialog will shown as below. Use the UP/DOWN or LEFT/RIGHT button to move the cursor to the character you want character, and press the OK button to select.
1.3.2 Favorites Manager Press the UP/DOWN keys to select the channel. Press the LEFT/RIGHT keys to select the favorite group. Press the OK button to add the selected channel to the Favorite group. To remove the channel from the favorite group, repeat same operation. Press RED key, you can sort the channels by different satellites. Press GREEN key, you can edit the favorite group name. 1.3.
1.4.1 My Album Select “My Album”, press the OK key, then press BLUE key. Use the ▲▼◄► keys to select a picture by thumbprint. To change Folder press the Blue key. 1. Press the OK key to play selected picture full screen. Files can also be selected by number keys and pressing the OK key. Colour keys provide a range of additional options. Red : zoom, Green: mp3 play, Yellow: flip horizontal. and Blue: flip vertical. 2.
1.4.4 Gomoku Line up the balls against the computer. Options include Move First, Move Later, Human; Easy and Normal. 1.5 Calendar View Calendars month by month from the year 1900 to 2100. Starts by highlighting today. Find out what day of the week you were born. 2.Other operation functions 2.1 Program List In normal operation status (no menu operation), press the OK button, the Program List menu will appear on screen. Press RED button to select sattellite in satellite list.
Press YELLOW button to sort program by Free-Pay. to select easy program you want. Press BLUE button to go back the screen before sorted. 2.2 System Information In normal operation status (no menu operation), press the INFO button, the Program Information menu will appear on screen. In this menu, the user can view the current program information. 2.3 EPG (Electronic Program Guide) The EPG shows the event information on the current TP channel by time zone. With MENU off, press the EPG button.
You can set up the event timer by pressing RED key in the EPG schedule screen. To set up an timer event: 1.Press UP/DOWN to move the cursor to the event for which you want to add a timer. 2.Press RED key to add a timer. shows you current event timer information based on the event you have chosen. You can also use this screen to modify each value. To save the settings, press OK. To quit event timer setup, press EXIT. EPG pre-recorded: the setting is the same as pre-recorded setting of timer. 2.
USER GUIDE TROUBLE SHOOTING GUIDE To assist in locating possible faults use the help guide below. SYMPTOM TROUBLESHOOTING No Picture, no sound Check that the TV is correctly plugged in. Check that the TV is connected to a suitable power source. Check the electrical supply is turned on. Ensure that the TV is powered on. Check that the cables are fitted securely. Ensure the aerial and/or external sources are connected. Press the INPUT button to change the source. Turn the TV on or off.
TECHNICAL SPECIFICATIONS Specifications of the TV that you have just purchased may vary from the information in this table due to technical innovations.
