55.5cm (22”) Full HD LED TV WITH DVB-S Model No.: LED-2215 For information and support, www.lenco.
Contents 1-3 SAFETY INFORMATION 4 Product Introduction 4 Front View 5 6 7 Connecting external devices Remote Control Basic Operation 8-15 8 10 11 12 13 14 15 OSD Menu 16-18 19-21 Multimedia Operation Recording Operation 22-36 Channel menu Picture menu Sound menu Time menu Option menu Lock menu Hotel menu DVBS Operation 37 TROUBLE SHOOTING GUIDE 38 TECHNICAL SPECIFICATIONS
SAFETY INFORMATION IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE. Take note of the following safety information which appears on the back of the TV. CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVER SCREWS, NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that there are important operating maintenance instructions in the literature accompanying this unit.
IMPORTANT SAFETY INFORMATION (Continued) This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use. Although this appliance has been carefully manufactured and rigorously checked prior leaving the factory, as with all electrical appliances it is possible for problems to develop.
IMPORTANT SAFETY INFORMATION (continued) Liquids spilt into the unit can cause serious damage. Switch the set OFF and disconnect the mains power supply, then consult a qualified service person before attempting to use the unit again. Do NOT remove the safety covers. There are no useable or serviceable parts inside. You may invalidate the warranty. Qualified personnel must only service this apperatus. Do NOT tap or shake the screen, you may damage the internal circuits.
Product Introduction Front View Led Indicator & Remote Control window SWITCH (Keep clear) Turn on/off the power supply. The functions of the TV buttons are described below. MENU: Press to display the OSD menu, Press again to exit the menu. CH-/CH+: Press to scan through channels. They are also can be used to move down/up in the OSD menu screen. VOL-/VOL+: Press to adjust the volume. They are also can be used to move left/right in the OSD menu screen. VOL+ button can be used to skip forward to next menu.
Connecting external devices (continued) Common Interface: CI slot. MINI AV RF RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal. MINI YPbPr MINI AV: Connect it to the audio & video output terminals of DVD with the Converter cable. (Audio terminals are shared with YPbPr) Coax MINI YPbPr: Connect it to the YPbPr video output terminal of DVD with the Converter cable. Coax: Digital audio output. PO VGA PC-IN POWER: Connect to the mains adaptor.
Remote control The remote control is using Infra-Red(IR). Point it towards the front of the TV. The remote control may not work correctly if it is operated out of range or out of angle. POWER PICTURE SLEEP SOUND CH.List ASPECT SUBTITLE INPUT MUTE POWER: Turn the TV on/standby. PICTURE: Select the picture mode. SOUND: Select the sound mode. CH/LIST: Display the programs list. INPUT: Press to display the input source menu. SLEEP: Standby timer.
Basic Operation Basic Operation Power on/off 1. Connect to the power supply with the power cord and turn on the switch 2. -To turn on the TV Press POWER button on the TV or remote control. -To turn off the TV Press POWER button on the TV or remote control.
OSD Menu OSD Menu 1. CHANNEL menu Description Auto Scan Press OK button to enter the hint menu, and select the Country and Tune Type mode for the TV, then press OK button to start auto tuning. DTV Manual Tuning Press OK button to enter the DTV Manual Tuning menu, select a DTV channel, and press OK button to start searching. ATV Manual Tuning Press OK button to enter the ATV Manual Tuning menu. Storage To: Select a position for storing the program. System: Select a TV system for searching.
OSD Menu OSD Menu Programme Edit Press OK button to enter the Programme Edit menu as the following picture. Rename Delete: Select a channel and press RED button, “Delete” will appear on the right of the program edit menu next to the channel you have chosen, then press RED button again, the program will be deleted. However if you decide not to continue to delete press the menu button to quit.
OSD Menu OSD Menu 2. PICTURE menu Description Picture Mode: Choose from Standard, Dynamic, User and Mild. Note: Contrast, Brightness, Color and sharpness are only available and can be adjusted in the User mode option in the Picture Mode Settings. Contrast: Controls the difference between the brightest and darkest regions of the picture. Brightness: Controls the overall brightness of the picture. Color: Control the color.
OSD Menu OSD Menu 3. SOUND menu SPDIF MODE PCM Description Sound Mode: Allows you to select among: Standard, Music, Movie, Sports and User. Treble(Could be adjusted when the sound mode is User): Controls the relative intensity of higher pitched sounds. Bass (Can be adjusted when the sound mode is set to User): Controls the relative intensity of lower pitched sounds. Balance: To adjust the balance of the left and right sound track, or turn off the volume of the left and right sound track.
OSD Menu OSD Menu 4. TIME menu No Action Auto Standby Time Zone Off Western Austr.. Description Clock: Use the time. and buttons to select the position, and use the and buttons to set the Note: User can not change time manually during DTV mode, for time is from signal source directly. Off Time: Press OK button to enter the submenu, you could set the time when the TV set will be turned off automatically, you could also set the frequency.
OSD Menu OSD Menu 5. OPTION menu OSD Duration Description OSD Language: Allows you to select menu language. Audio Language 1st/2nd (can be selected in DTV mode): Allows you to select first and second audio language. Subtitle Language 1st/2nd (can be selected in DTV mode): Allows you to select first and second subtitle language. OSD Duration: Allows you to setup the time of the menu display on the screen among: 5s, 10s, 15s, 20s, 25s, 30s, 35s, 40s.
OSD Menu OSD Menu 6. LOCK menu Hotel model Description Lock System: Turn on/off the Lock System function. Note: You should enter the code to operate the menu.(original code is 0000) Set Password: Set pin code. If the Pin code has been changed you must enter the present code. New : Enter the new password. Confirm: Enter the new password. Block Program: Lock the channel, you have to enter the code to view the channel.
OSD Menu OSD Menu 7.
Multimedia Operation Multimedia Operation Basic Operation 1). Press the INPUT button on the remote control to display the input source menu, select USB source by the / buttons, and press OK button to enter the Multimedia menu seen below. Input Source DTV CADTV ATV SCART YPBPR DVB-S PC HDMI AV USB Select 2). Insert USB device, you will find the name of the device display on the screen.
Multimedia Operation Multimedia Operation 1. Photo Play the photo Press / button to select the option on the table, and press OK button to change. Repeat: Select the repeat mode from Repeat All, Repeat 1, Repeat None. Music: Play/pause the music program (you can only play or pause the music you have programed). Playlist: Display the playlist on the screen, and you can select the photo by / button, and press OK button to program. Press / button to return to the options table.
Multimedia Operation Multimedia Operation 3. Movie Play the movie Goto Timer Press / button to select the option on the table, and press OK button to change. Repeat: Select the repeat mode from Repeat All, Repeat 1, Repeat None. Set A-B: Select and play the preferable paragraph of the program by seting A and B at the beginning and end, and there will be a sign on the left screen, press OK button again to cancel. Playlist: Display the playlist on the screen. Info: Display the information of the movie.
Recording Operation Recording Operation PVR settings Press the MENU button, and select CHANNEL menu. Recording Timer 1). Recorded List Channel Recorded list: Display the Recorder List menu. INFO: Display the information of the program you recorded. RED button: Delete the program you select. 2). Recoring Time Recoring Time Set the recording timer The TV will record the program automatically according to your settings. TITLE: Display the name of the recording program. MODE: Select the record mode.
Recording Operation Recording Operation 3). Schedule List Display the recorder shedule Note: a. Could’t add shedules which have existent on the list; b. Could’t add shedules when the list is full, you have to delete some schedules; c. You could delete a schedules by RED button on the remote control. 4). PVR File System Setup the PVR File system before you start recording. Select Disk: Select the device for the Record files. Check PVR File System USB Disk: Display the USB state.
Recording Operation Recording Operation 5) Record Start When you finish the settings above, you could start recording by select Start Recording in the menu and press OK button in DTV mode. (You can also start recording by press the REC button on the remote control) Record buttons REC(Recording): Press to enter the recording mode. PAUSE: Press to enter the timeshift mode. Recording list: Press to display the recording list. Stop: Press to stop recording.
DVBS Operation 1 Main Menu All the important settings and features of your receiver can be operated in Main Menu. The Main Menu consists of four sub-menus which are "Installation", “System setting”, "Channel Organizer" and "Multimedia". Press the MENU key when the menu is off, The MAIN MENU screen will appear 1.1 Installation The installation menu contains three sub-menus; “Dish Setup”, “Auto Scan” and “Transponder Manager”. 1.1.
1.1.1.2 Transponder You can select the current Transponder or add the new Transponder. 1.1.1.3 Local Frequency You can change the local frequency. Note: You must press OK to save this local frequency when the cursor is on the Local Frequency item before you select another satellite. 1.1.1.4 22K Tone You can change the 22k tone. Press LEFT/RIGHT select ON, OFF or AUTO. Note: You must press OK to save this 22K tone when the cursor is on the 22K Tone item before you select another satellite. 1.1.1.
Move the curser to Back or Next button and press OK to exit the submenu to the last menu. When you select DiSEqC1.2: Press OK to enter the submenu of the Adjust Antenna. Press UP/DOWN to move the curser to the item of the Transponder. Press LEFT/RIGHT to select the current transponder. Press UP/DOWN to move the curser to the item of the Move Dish. Press LEFT/RIGHT to move dish. Press UP/DOWN to move the curser to the item of the Goto Ref.. Press OK to go to 0.
1.1.2 Auto Scan Press UP/DOWN key to move the curser to the satellite you want to select, and press OK to mark or unmark. Press the RED button to scan all channel of the marked satellite. Press the GREEN button to Blind Scan the marked satellite. Press the YELLOW button to scan free channel of the marked satellite. 1.1.3 Transponder Manager In this menu, you can add, edit, and delete the transponder. you can search transponder. 1.1.3.1 Satellite You can select the satellite. 1.1.3.
1.1.3.3 Polarity You can select the polarity. 1.1.3.4 Symbeol Rate You can select Symbol Rate. 1.1.3.5 NIT Searching You can select the NIT Searching. 1.1.3.6 Free You can select the free mode. . 1.2 System setting In this menu, you can configure the systems such as language Setting, OSD style, Parental Control, TV Settings, Time Setting and System Update. 1.2.
1.2.1.5 Time Setting Press OK go to Time Setting below: If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. If the GMT usage is ON then the Current time is set automatically or you can set the time zone. If your broadcaster provides the correct time offset then your receiver will change from summertime to wintertime automatically. If you set GMT Usage to OFF, Set Data and Set Time item are displayed.
Ɣ Change PIN Modifying the PIN. You must enter the 4 digits PIN and confirm it again; the system PIN will be changed into the new PIN as show on. 1.2.3 System Update In this menu, you can select “Update by OTA”, “Update by DEV ” Ɣ Update by DVBS You can update your STB software by USB. Select “System Update – Update by DEV”, you can select update software from USB disk, and press OK key to update your DVBS.
1.2.4 System info The system information displays information about your receiver such as software hardware and date. 1.2.5 Timer You can set the timer to make the receiver perform designated actions. Use the UP/DOWN buttons to select timer. Press the LEFT/RIGHT key to activate/inactivate current timer. Press the OK button to enter your selected timer settings.
1.3 Channel Organizer In the MAIN MENU screen, press UP/DOWN to move the cursor to Channel Organiser, and then press OK to enter the Channel Organizer menu. The Channel Organizer menu consists of three sub-menus; “Channel Manager” , “Favorites Manager” , “Remove Satellite” . 1.3.1 Channel Manager In this menu, you can change the order of the channels, delete and edit channels. To change the satellite use the RED button, and press Left/Right button.
Edit (YELLOW button) Select the channel that you wish to edit, press the YELLOW (Edit) button to move into the modify program menu. In this menu, you can modify the Program Name, Frequency, Symbol rate, Video PID, Audio PID. If you want to rename the channel, use the UP/DOWN keys to select “program Name” and press OK, the program name dialog will shown as below. Use the UP/DOWN or LEFT/RIGHT button to move the cursor to the character you want character, and press the OK button to select.
1.3.2 Favorites Manager Press the UP/DOWN keys to select the channel. Press the LEFT/RIGHT keys to select the favorite group. Press the OK button to add the selected channel to the Favorite group. To remove the channel from the favorite group, repeat same operation. Press RED key, you can sort the channels by different satellites. Press GREEN key, you can edit the favorite group name. 1.3.
1.4.1 My Album Select “My Album”, press the OK key, then press BLUE key. Use the ŸźŻŹ keys to select a picture by thumbprint. To change Folder press the Blue key. 1. Press the OK key to play selected picture full screen. Files can also be selected by number keys and pressing the OK key. Colour keys provide a range of additional options. Red : zoom, Green: mp3 play, Yellow: flip horizontal. and Blue: flip vertical. 2.
1.4.4 Gomoku Line up the balls against the computer. Options include Move First, Move Later, Human; Easy and Normal. 1.5 Calendar View Calendars month by month from the year 1900 to 2100. Starts by highlighting today. Find out what day of the week you were born. 2.Other operation functions 2.1 Program List In normal operation status (no menu operation), press the OK button, the Program List menu will appear on screen. Press RED button to select sattellite in satellite list.
Press YELLOW button to sort program by Free-Pay. to select easy program you want. Press BLUE button to go back the screen before sorted. 2.2 System Information In normal operation status (no menu operation), press the INFO button, the Program Information menu will appear on screen. In this menu, the user can view the current program information. 2.3 EPG (Electronic Program Guide) The EPG shows the event information on the current TP channel by time zone. With MENU off, press the EPG button.
You can set up the event timer by pressing RED key in the EPG schedule screen. To set up an timer event: 1.Press UP/DOWN to move the cursor to the event for which you want to add a timer. 2.Press RED key to add a timer. shows you current event timer information based on the event you have chosen. You can also use this screen to modify each value. To save the settings, press OK. To quit event timer setup, press EXIT. EPG pre-recorded: the setting is the same as pre-recorded setting of timer. 2.
USER GUIDE TROUBLE SHOOTING GUIDE To assist in locating possible faults use the help guide below. SYMPTOM TROUBLESHOOTING No Picture, no sound Check that the TV is correctly plugged in. Check that the TV is connected to a suitable power source. Check the electrical supply is turned on. Ensure that the TV is powered on. Check that the cables are fitted securely. Ensure the aerial and/or external sources are connected. Press the INPUT button to change the source. Turn the TV on or off.
TECHNICAL SPECIFICATIONS Specifications of the TV that you have just purchased may vary from the information in this table due to technical innovations. TV Specifications TV System PAL / BG / DK / I; SECAM BG/DK/L’L Audio System BG / DK / I SECAM L/L’ Screensize 21.6”(Diagonal) Resolution 1920 x 1080Pixels(RGB) Aerial input 75 Audio output power 2 x 3W Power requirements 12V 3.
I LENCO II LED-2215 30 55,5 44 22
