CD Micro System with DAB+ MC-148 DAB+ USER MANUAL www.lenco.com Please read this manual carefully before connecting or operating the appliance. Save it for future reference.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTION ........................................................ 2 PANELS AND CONTROL ............................................................................. 4 PREPARATION FOR USE............................................................................ 5 GENERAL OPERATION ............................................................................... 6 CD OPERATION ...........................................................................................
IMPORTANT SAFETY INSTRUCTION CAUTION! RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) • When using electrical equipments basic safety precautions should always be followed. • This equipment is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience or knowledge.
IMPORTANT SAFETY INSTRUCTION • Refer all serving to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture. • Please keep the unit in a good ventilation environment. • These servicing instructions are for use by qualified service personnel only.
PANELS AND CONTROL FRONT PANEL 1 2 3 4 5 6 7 8 9 10 STOP/MENU 11 12 AUDIO IN REAR PANEL 14 13 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Indicator STANDBY mode Display PLAY/PAUSE button SOURCE button STOP/MENU button CD loading drawer EJECT button IR sensor VOLUME knob PREVIOUS/NEXT button AUDIO input 13. FM antenna 14. Speaker connectors 15.
PREPARATION FOR USE CONNECT WITH SPEAKERS PEAR PANEL LEFT SPEAKER ANTENNA SPEAKERS(8Ω) RIGHT SPEAKER 1. Unwarp the speaker wires. 2. Place a speaker on either side of the main unit, preferably at the same height, and with at least 150mm between each speaker and the main unit. 3. Connect the speaker plugs to rear of the unit. Take care to match the speaker placed to the LEFT output on the rear of the unit. Repeat for the RIGHT speaker. 4.
GENERAL OPERATION STANDBY MODE Press the STANDBY button on the unit or the remote control to turn on the system or to put the system into standby mode. To resume normal operation, press either button again. VOLUME CONTROLS Rotate the VOLUME control clockwise or press the VOLUME+ button to increase the volume level. Rotate the VOLUME control anti-clockwise or press the VOLUME- button to decrease the volume level. MUTE FUNCTION Press the MUTE button at any time to silence the output. Press again to resume.
CD OPERATION PLAYBACK 1. Make sure you are in CD mode, if not press the CD button on the remote or press the SOURCE button until you reach CD. 2. Press the EJECT button, when the disc drawer pops out insert a disc (label side facing upwards), press the EJECT button again to close. 3. When the door is closed “LOADING DISC” will appear on the display as the unit detects compatible audio tracks. 4. Playback will begin automatically from Track 01. 5. To stop playback, press the STOP/MENU button once.
NUMERIC BUTTONS 0-9 While listening to a CD a specific track number can be played by pressing the relative digit on the number buttons. e.g.: track 6 would be 06. To play track 12 you would press the 1 button then 2. CD OPERATION PROGRAM PLAYBACK You may wish to play back tracks of a CD in a different order than the original disc was recorded in. 1. Press the PROGRAM button to enter the program setup function. 2. Use the / buttons to skip between the play order numbers. 3.
NOTE: The SHUFFLE play is only available on standard music Cds, not Mp3 Cds.
DAB+ OPERATION Switch to DAB+ mode by pressing SOURCE button on the unit or DAB/FM button on the remote control. AUTO SCAN MODE 1. To activate the full scan press the STOP/MENU button. 2. When you see the option, press the PLAY/PAUSE or ENTER button. The unit will search for all available DAB+ stations that can be tuned. MANUAL TUNING As well as an auto tune function, you can manually tune the receiver. 1.
DAB+ OPERATION RECALLING A STATION PRESET To select a preset, just press the required numeric button while in DAB+ mode to activate the station you stored. DISPLAY MODES Every time you press the INFO button on the remote control, the display will cycle through the following display modes: The information is displayed on the lower segment of the LCD display.
DAB+ OPERATION Channel Frequency Displays the frequency information for the current station. Signal Error Displays information regarding the error rate in the signal. Bit Rate This displays the type of broadcast you are receiving e.g. mono or stereo and what bit rate is being used. SECONDARY SERVICES On some occasions you will see a “>>” symbol directly after the name of the station. This indicates that there are secondary services available to that station.
DAB+ OPERATION DRC (DYNAMIC RANGE CONTROL) This causes the radio to reduce the dynamic range of the audio signal. The purpose of this is to adapt the dynamic range of the audio signal to listening in a noisy environment. NOTE: this is not available on some DAB+ stations. 1. Press the STOP/MENU button in DAB+ mode, and use either / on the unit, / on the remote to find . Press the PLAY/PAUSE button on the main unit or ENTER button on the remote. 2.
FM OPERATION Switch to the FM mode. SCANNING FOR STATIONS 1. You can scan up or down the frequency range manually by pressing the / buttons on the remote or pressing / buttons on the unit to increase or decrease the frequency in 0.05MHZ increments. To scan through the frequency range quickly press and hold the / buttons on the unit or press the / buttons on the remote control. 2. Once a station has been found, the scanning will stop automatically.
FM OPERATION RECALLING A STATION PRESET To select a preset, just press the required numeric button while in FM mode to activate the station you stored. DISPLAY MODES Every time you press the INFO button on the remote control, the display will cycle through the following display modes: The information is displayed on the lower segment of the LCD display. Audio Mode (Stereo/Mono) PTY Radio Text Name Audio Mode This denotes whether the stations is in stereo or mono.
EXTERNAL INPUT CONNECTING AN EXTERNAL AUDIO DEVICE External audio sources such as iPod's & MP3 players can be connected using a 3.5mm to 3.5mm audio cable (not supplied). Mp3 player 1. Connect one end of the cable to the AUDIO devices headphone/Line output and the other end to the AUDIO IN input on the front of the unit. 2. Press the SOURCE button until you reach the AUX IN option or press the AUX IN button on the remote control. 3. Adjust the volume to your desired level.
Speaker Size 130 x 186.5 x 125 mm Net Weight 3.0kg(Approximate) TROUBLESHOOTING In the unlikely event of difficulties with your appliance please follow the trouble shooting guide below. Problem Reason(s) Solution(s) No Power Power cable not Make sure the plug is connected to wall connected. socket. Power socket is Switch the power on. not switched on. No Sound CD/AUX/RADIO. No Sound from AUX input. Volume is too low. AUX source volume is too low. Sound is distorted.
minutes of inactivity. Press the STANDBY button to wake the unit. SERVICE AND SUPPORT For information: www.lenco.com Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer. Important note: It is not possible to send products that need repairs to Lenco directly. Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
