MDV-7 2.1 DVD Home Cinema Centre For information and support, www. lenco.
FOREWORD THANKS Thank you for purchasing this product. Your choice of the product sufficiently displays your expertise in acoustic equipment. We are honored to provide you with more satisfactory products. It is suggested that you spare some time to read this user manual before connecting and operating your system. So you can get enhanced enjoyment and pleasure while using this product. IMPORTANT NOTICE Please unpack carefully, and keep all the accessories in the same place.
CONTENT FOREWORD……………………………………………………………………………………..1 CONTENT………………………………………………………………………………………...2 FRONT PANEL...………………………………………………………………………………..3 BACK PANEL……………………………………………………………………………………4 REMOTE CONTROL……………………………………………………………………………5 CONNTECTION WITH TV……………………………………………………………………...6 CONNECTION WITH AMPLIFIER………………………………………………………….….7 SYSTEM CONNECTION…………………………………………………………………….….8 BASIC OPERATION……………………………………………………………………..…..9-16 DVD MENU SETUP…..…………………………………………………………………….
FRONT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. STADNBY REMOTE CONTROL SENSOR DISC TRAY (F.RWD/TUNE-)/(F.FWD/TUNE+) (PREVIOUS/CHANNEL-)/(NEXT/CHANNEL+) USB AND MULTI-MEDIA CARD PORTS OPEN FM/DVD/AUDIO DISPLAY SCREEN PLAY/ENTER 11. STOP 12.
BACK PANEL 1. FM ANTENNA INTERFACE 2. SCART OUTPUT 3. VIDEO OUTPUT 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
REMOTE CONTROL NOTE: 1. Place the batteries in the remote control and turn on the player; put the emitter against the sensor of player for remote control. 2. The distance of remote control should not exceed 7 meters, or else, it will be invalid. 3. If the sensor or remote control emitter is stuck with foreign matters, it may result in the malfunction in signal reception or not at all. 4.
CONNECTION WITH TV 1. If your TV-set has AV terminal, connect this unit to TV-set with A/V cables, and set TV-set to be AV status after confirming the connection is correct. (Figure 1) 2. If your TV-set has S-Video terminal, please use the S-Video connection cable to connect the player and TV-set, to obtain a higher quality image. (Figure 2) 3. If your TV-set has chromatics output terminal, please use three connection cables to connect the player and TV-set, to obtain a more vivid image. (Figure 3) 4.
CONNECTION WITH AMPLIFIER Setup of Digital Audio Output Connect the optical or coaxial output jack to the amplifier. While in of play or stop mode, press the Setup button on the remote control to open the system setup page, switch to audio setup page by pressing the directional buttons, then move the cursor to Audio Out, select SPDIF/RAW or SPDIF/PCM, press Play/Enter button to finish. Press Setup button again to exit the setup.
SYSTEM CONNECTION Please refer to the following figure to connect your acoustic equipment. To keep all the connection correctly and firmly. Power supply can be connected finally.
BASIC OPERATION PREPARATIVE 1). Before turning on, check whether all the connection are correct and reliable. Plug the power plug into the corresponding power socket. 2). Press STANDBY button on the front panel to turn on. 3). Press EJECT button on the remote control (or OPEN button on the front panel) to carry the disc tray outside, put the disc into the tray, press EJECT or OPEN button again, this unit starts to read and play the disc.
BASIC OPERATION TIME SELECTION In play mode, press T/F button on the remote control, the TV screen displays: You can press ◄►directional buttons to move the cursor to the setting option according to the above mentioned screen suggestions, then press PLAY/ENTER to confirm and use number buttons to input the corresponding time numbers. After it is done, DVD player will start to the next item in the above screen.
BASIC OPERATION LOUDNESS Press LOUD button to set loudness on or off. While set loudness on, it can strength low sound signal. TITLE If the played DVD disc contains a directory column, press the TITLE button to take out the items contained in this disc. Use the direction buttons to move the cursor to select the items you want to play, or directly use the number button to select. SOUND FIELD In play status, press DSP button, you can select different sound field effect.
BASIC OPERATION PLAY/ENTER Press PLAY/ENTER button to playback or enable the selected items. CLEAR Press CLEAR button to cancel the digital you have inputted. For example: the setting of programmed songs. STANDBY Press the STANDBY button on the remote control can switch to the standby mode. Before you perform the operation, make sure the main power is on. Note: This standby function is one kind of saving electricity modes. When the device does not be used for a long time, please disconnect the main power.
BASIC OPERATION NUMBER BUTTONS 1). While playing songs, press the Number buttons to directly select the songs you need. 2). If the desired track number is # 10 or above, you can select it by pressing the 10+ button once, and then pressing a Number button (1--10). For example: If the 16th song is needed, you can press the 10+ button followed by the 6. PROGRAM ●In play DVD, press Program button, the TV screen shows: ●In play VCD/CD optional, and press Program button, the TV Screen shows: 1.
BASIC OPERATION 2). Press the directive keys ▲▼ to move the cursor to a certain directory, and press PLAY/ENTER button to enter the directory. Press the direction buttons to enter the subdirectory or the file area, select a song with the cursor, press PLAY/ENTER button to play the song. l During playing, press or button to select other songs under the current directory.
BASIC OPERATION DVD/USB/CARD It is possible to listen to the audio and watch Video/JPG files using the USB/CARD interface of this unit. Before entering the USB/CARD mode, please switch to DVD mode first. In order to view the contents of the USB/CARD, the following operations need to be performed. 1. 2. Connecting the USB device or CARD with this unit. Press the DVD/USB/CARD button on the remote control; the dialogue window will appear on the TV screen.
BASIC OPERATION FM RADIO OPERATION 1. Enter FM Function In the turn-on or playing status, press the FM button on the remote control to enter FM status. 2. Select Bands 1) Directly input frequency: press the T/F button on the remote control; input the frequency that you want directly. 2) Select band by pressing TU- or TU+ button: under some frequency, press the button, the frequency will be up or down on the step. The step of FM is 0.05 MHz.
DVD MENU SETUP Press the SETUP button on the remote control to open the menu setup function, the TV screen will display the following figures. Press Left/Right direction buttons to move the different setup pages; Also you can press the direction buttons to move cursor to the item you want, then press PLAY/ENTER button again to enter the subdirectory. 1.
DVD MENU SETUP 2. Audio Setup Page 1) Analog Audio Setup (1) Downmix LT/RT: audio output from Left and Right channel Stereo: stereo audio output (2) Dialog This option is used to adjust the Dialog level. 2) Digital Audio Setup (1) Digital Output When playing the DOLBY, or MPEG disc, the optical or coaxial terminal will be output in SPDIF/RAW format. Meanwhile the connected amplifier must be able to decode the DOLBY DIGITAL or MPEG.
DVD MENU SETUP (3) Super Bass ON: set the super bass on, and adjust the super bass effect. OFF: set the super bass off. (4) Treble Boost ON: set the treble boost on and adjust the treble effect. OFF: set the super treble boost off. 5) 3D Processing Reverb Mode This option has different reverb modes setting: Concert, Living Rom, Hall, Bathroom, Cave, Arena, Church. 6) HDCD Filter This option has three settings: OFF, 44.1KHz, 88.
DVD MENU SETUP 4. Preference Setup Page (This setup page only be available when the player in No Disc or Eject status.) 1) TV Type Select the corresponding TV system to fit your system; PAL, AUTO, NTSC system are available of this device. 2) PBC This option is used to open or close PBC. 3) Audio Select the desired audio language (English, French, German, Spanish, Dutch, Portuguese, Italian, Others).
5. Password Setup Page Password Mode/Password The original password of this unit is “138900” and you can change it to a new one. 6. Exit Setup Page This option is use to exit the Setup menu; you can also pres the Setup button on the remote control to exit.
SPECIFICATION Disc type DVD SVCD VCD CD MP4 JPEG MP3 Video format MPEG2 for DVD, and MPEG1 for VCD. Audio format MPEG1, MPEG2, PCM, Stereo Signal output Video format: NTSC, PAL, AUTO Video output:1.0V p-p Audio: Stereo, 1.
TROUBLESHOOTING Please use the following methods to solve the following problems while using this unit.