PA-45 Portable Sound System with Bluetooth® USER’S MANUAL www.lenco.com Thank you very much for buying this Mobile Battery Bluetooth Speaker! In order to make the speaker function best, please take time to read this instruction manual carefully before use. It will help you to know every function better. Please keep well this user’s manual for long-time reference.
1) WARNING: The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. 2) This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
CAUTION To avoid failure and damage when using this device, please read this user’s manual and make sure that you fully understand the safety and operation instruction. These instructions should be kept for your long-time reference. 1. This speaker offers you 2 different power supplies: AC 230V 50/60Hz, and rechargeable lead-acid battery DC 12V 2.6Ah. 2. DO NOT attempt to touch any inside parts of the speaker system to avoid any possible risk of electronic shock. 3.
FEATURES 1. Designed with AB audio processor and BTL output to produce crystal clear sound and strong bass 2. Special structure designs with electrical-short-circuit protection 3. Built-in rechargeable lead-acid battery for outdoor usage 4. Built in a Wired MIC Input with Vol. and Echo controls 5. Built in a Guitar Input 6. With auto detect USB & SD card reader function for Mp3 decoding 7.
Bluetooth: Press the INPUT SWITCHING Button until the BLUETOOTH Indicator blinks. The BLUETOOTH function is ON. Turn on the BLUETOOTH in device and start searching for this BLUETOOTH speaker. You will find device name of LENCO PA-45. Select this to link to the speaker. The Indicator will stop blinking and light up in BLUE color when you are successfully linked. After the linking, you can start to play music from your device.
Back Panel: 1. Power Jack: Insert the power cord to this jack and connect to AC 230V 50/60Hz. 2. Power Source Switch: AC INPUT, F.CHARGE/OFF, DC INPUT 3. AC Power Switch: AC ON, OFF, CHG ON How to Use the Switch: AC Power Supply, connect the power cord to AC 230V 50/60Hz, switch the Power Source Switch to AC INPUT, and switch the AC power switch to AC ON. To turn the system off, switch both to OFF. This operation is suitable for indoor use.
9. AUX input 10. Power indicator 11. Charging indicator: When charging, the CHG indicator blinks in RED. When charging is almost completed, it blinks in GREEN. When completing charging, the indicator keeps on in GREEN. 12. USB/SD indicator 13. AUX/BT indicator 14. SD card 15. USB Port 16. Guitar Input 17. MIC Input 18. Wired microphone volume control 19.
Operation Reference Power AC Power Source Power Indicator CHG Indicator Power Management Unit Operation Powered by AC and Battery Charged Will AC INPUT AC ON ON Refer YES REMARK go into standby and charging cease after no signal input for 15 minutes AC INPUT OFF OFF OFF Not applicable Switch AC Power switch to OFF, and then AC ON to power on the system again.
Mode USB/SD Indicator USB SD AUX IN Bluetooth Blink Blink ON OFF AUX IN/BT Indicator OFF OFF ON Blink TROUBLESHOOTING Troubles Possible Reasons Trouble Shootings Power Indicator OFF and NO sound coming out 1. AC Power Button is still OFF 2.Battery run out of power 1. 2. Turn the AC Power Button to ON. Connect the power cord to AC 220V/50Hz outlet to test if speaker still working and to re-charge the battery. Power Indicator ON But NO sound coming out 1. Wrongly connect the RCA or 3.
This product operates at 2400 - 2483.5 MHz and is designated only to be used inside a normal household environment. This product is suited for this purpose within all EU countries. Hereby, STL Group BV, Ankerkade 20 NL 5928 PL Venlo, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at https://lencosupport.zendesk.
