SCD-2000 BT Boombox with slot-in CD/MP3 player, AM/FM radio and Bluetooth® User manual www.lenco.com 20121004 v1.
Table of content What’s in the box? ...................................................................................................... 4 Exploring the device ................................................................................................... 5 Front view ............................................................................................................................... 5 Rear view .................................................................................................
Basic Operation during playback from an SD card ...................................................................... 17 Playback from a Bluetooth® device ..................................................................................... 18 Basic Operation during playback from a Bluetooth® device ........................................................ 18 Connections .............................................................................................................
Dear customer, Thank you for choosing for Lenco. At Lenco, we are convinced that everyone should enjoy life as much as possible. Our products are meant to support, improve and create joyful moments for everyone. For this reason, we offer user-friendly, highquality and well-designed consumer electronics for an excellent price. This user manual is designed to help you with the features of this device. Note: This user manual was written during the development of the product, based on the factory settings.
Exploring the device In the user manual, every feature or action always includes the number of the button or part that is used, so that you can easily recognize the buttons or parts that are needed. Front view 1. Handle, use the handle to lift the device. 2. CD slot, you can insert a CD into the CD slot. Always insert a CD with the label facing up. 3. Source button, press this button to select the source. 4.
7. Equalizer button, press this button to browse through the different equalizers. 8. Volume buttons, these buttons can be used to control the volume. Press the volume + button to increase the volume, press the volume – button to decrease the volume. 9. USB port, slide the cover backwards to reach the USB port. Use the USB port to connect a USB storage device. 10. SD card slot, slide the cover backwards to reach the SD card slot. Use the SD card slot to insert an SD card. 11.
Rear view 19. Shoulder strap attachment points, the shoulder strap can be attached to these points. 20. USB charger with mini USB connector, a device can be charged using this connector. 21. Telescopic antenna, the antenna receives the AM / FM radio signals. 22. Battery compartment, insert the batteries in this compartment. 23. AC connection, connect the power cord to this connection.
Afstandsbediening 24. Power button, press this button to turn the device on or off. 25. Play / pause, mem+ button, use this button to pause a track or to browse through the preset stations. 26. Folder, FM ST button, use this button to skip 10 tracks or to switch between mono and stereo radio reception. 27. Equalizer button, press this button to browse through the different equalizers. 28. Mute, press this button to mute the sound. 29. Source button, press this button to select the source. 30.
Getting started Where to install Never place the device in direct sunlight. Place it on a sturdy platform of which the surface should be flat and steady, so the product can’t fall or hit by any objects. Make sure the product is placed in such a manner that nothing can fall on top of it, as pressure will damage or break the product. Prevent insertion of objects into the ventilation slots, or openings in the cabinet at all time. Always read the safety instructions carefully before use.
Installing backup batteries By installing batteries in the backup memory battery compartment, the device will always be powered. The device needs to be powered to store the things in memory. When the device is connected to the mains, the batteries will not be used. When utility power fails, the device will automatically switch to the backup memory batteries. Things that are stored in memory are the pair & play® data, preset radio stations and clock settings.
Using the device on batteries If the device is connected to the mains, first disconnect the power plug from the outlet. Open the battery compartment (22) and install the batteries. Always remove the batteries from the device when the device will not be used for long periods or when the device is connected to the mains. Attaching the shoulder strap The shoulder strap allows you to bring the device anywhere you go. Attach the strap to the attachment points (19) as indicated in the figure below.
Replacing the battery of the remote control When the remote control stops working or stops working properly, the battery should be replaced. Replace the battery as follows: 1. Press the catch at arrow 1 in the direction of arrow 2 and hold it. 2. Pull the battery tray out by pulling it in the direction of arrow 2. 3. Replace the battery with a new one and slide the battery tray back in the remote control. Note that the + side of the battery is facing up. The model number of the battery is CR2025.
3. Go to the Bluetooth® menu on the external device and click on "Lenco". The devices will now establish a connection. Depending on the external device, you may have to give Lenco permission to automatically connect to the external device. To increase user-friendliness, Lenco advises to allow establishing an automatic connection. 4. Go to the music player on the external device and export your favourite music to the Lenco boombox.
Turning the radio on Press the Power button (13, 24) to turn the device on. If the radio is not in radio mode, press source (3, 29) until the display (14) shows "Rad". Once "Rad" has disappeared, the frequency and the band (AM/FM) are shown on the display (14). Switching between AM/FM This device has an AM tuner with a frequency range from 522 kHz to 1620 kHz and an FM tuner with a frequency range from 87,5 MHz to 108,0 MHz. Press the Band button (12, 31) to switch between AM and FM.
Switching between mono and stereo Some channels can only be received in mono while some others might have bad stereo reception, causing noise. When there is noise while receiving a stereo station, the sound can be improved by switching to mono. Press the FM ST. Button (5, 26) to switch between mix mono and stereo mode. When the device is in stereo mode, "(ST)" will be shown on the display (14). Playing a CD Audio, MP3 and WMA CDs can be played with the built-in CD player.
extension cable. Open the USB / SD cover by sliding it towards the handle (1) as can be seen in the figure below. Connect the USB storage device, when it is connected properly, the radio will start reading the device. Once the USB storage device is read, the radio will automatically start playback. Basic Operation during playback from a USB storage device Pause playback, press the play / pause button (15, 25) during playback to pause playback.
SD card playback Through the built-in SD card slot (9) MP3 and WMA files can be played. Enter the SD mode by pressing the source button (3, 29) until CARD is shown on the display (14). Open the USB / SD cover by sliding it towards the handle (1) as can be seen in the figure below. Insert the SD card, when it is connected properly, the radio will start reading the device. Once the SD card is read, the radio will automatically start playback.
Playback from a Bluetooth® device Through the built-in Bluetooth® receiver, music can be wirelessly streamed from an external Bluetooth® device to the Lenco boombox. Enter the Bluetooth® mode by pressing the source button (3, 29) until BLUE is shown on the display (14). The boombox will automatically try to connect to the last paired device. If pairing fails or if you want to connect to a different Bluetooth® device, hold the pair button (12, 32) until the Bluetooth® logo is blinking on the display (14).
Connections Connecting a device through the AUX input Every device with an AUX output or headphones output can be connected to the AUX input that is located in the storage compartment (18). To connect a device to the input, the storage compartment (18) has to be opened first. After opening the compartment, pull the AUX cable out and connect the external device as shown in the figure below. When the external device is connected through the AUX input, the volume can only be controlled through the boombox.
Advanced Using the storage compartment Open the storage compartment (18) and loosen the Velcro. Place the device carefully on the holders and then fix it using the Velcro. Setting the equalizer This boombox is equipped with several equalizer presets. The equalizers can be used to adjust the sound settings to your genre, so that music sounds better. You can choose from: Rock, Classic, Pop, Jazz. Press the EQ button (7, 27) to switch between the different equalizer presets.
Troubleshooting Problem The device is not turning on. The device is not responding well. When using batteries, sound is soft or distorted. Settings or options are suddenly cancelled. Radio stations can barely be heard because of noise or cannot be received. Bluetooth® music stutters. Music playback stutters while playing a CD. The remote control is not working or not working properly. Solution Check if the plug is inserted firmly into the outlet. Replace the batteries.
Specifications AC ~ 100-240V, 50/60Hz Power supply Battery 8x UM2 Backup memory battery 2x UM4 Device operates 6 hours on batteries during normal use Power connection Power consumption Operating Output 1,5M euro plug.
Safety instructions Explanation of symbols: This symbol indicates that there are important operating maintenance instructions in the user manual accompanying the device. This symbol indicates that dangerous voltage is present within this device, constituting a risk of electronic shock or personal injury. CAREFULLY READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE USE.
Do not use this device when condensation may occur. Do not use this device near water or other liquids. Do not use this device in a damp room. Do not use this device near a swimming pool. Electrostatic interference may interfere with the normal use of this device. If this occurs, reset the device and restart it according to the instructions in the user manual. The display is made of plastic and might break when it’s damaged.
Do not distribute copyrighted material Do not distribute copyrighted material without the permission of the owners. By doing this you risk violation of copyright laws. The manufacturer is not liable for any legal issues caused by illegal use of copyrighted material by the user. Disclaimer Some content and services accessible through this device belong to third parties and are protected by copyright, patent-, trademark- and/or other intellectual property laws.
End of life This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries.
Service and support For information and support about the hardware: www.lenco.com Lenco helpdesk: Germany 0900-1520530 (Local charges) The Netherlands 0900-23553626 (Local charges + 1ct P/min) Belgium 02-6200115 (Local charges) France 0170480005 (Local charges) The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM.
©2012 STL Group B.V. all rights reserved, Lenco is a trademark of STL Group B.V. STL Group B.V. is not responsible for any printing errors in this manual. Products of other manufacturers are only mentioned for information. This does not mean that these products are recommended by STL Group B.V.. STL Group B.V. accepts no liability for the reliability or compatibility of these products.
