STB-100 Set top box with HD DVB-T User’s Manual For information and support, www.lenco.
Table of Content 1. Main Features ……………………………..……………………………………..4 2. REMOTE CONTROLLER ……………………………………………………...6 3. Welcome Page ………………………………………………………..…….....8 4. Installation Gudie ………………………………………………………………8 5. Program …………………………………………………………………….……8 5.1 Program Edit ……………………………………………………..……9 5 .1 .1 Mo v e … … … . …………………………………………..……… 9 5.1.2 Skip ……………………………………………………………..…….9 5.1.3 Lock ……………………………………………………………..……..9 5.1.4 Delete……………………………………………………………..……9 5.1.5 Favorite………………………………………………………………....10 5.1.
SAFETY PRECAUTION CAUTION: The lightning flash with Warning: The exclamation point arrowhead symbol, within To reduce the risk of within an equilateral an equilateral triangle, is electric shock, don't open triangle is intended to intended to alert the user the cabinet. Refer alert the user to important to "dangerous voltage" servicing to qualified operating and and to prevent from a risk personnel only. maintenance (servicing). of electric shock.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it from overheating. Do not block these openings or allow them to be blocked by placing the STB on a bed, sofa, or other similar surface, nor should it be placed over a radiator or heat register. Power-Cord Protection: Place the power-supply cord out of the way, where it will not be walked on. Please take special attentions to cords at plugs, convenience receptacles, and the point where they exit from the unit.
Preface Congratulations on your purchase of the set top box, Before operation, please read this manual thoroughly and keep it well for future reference. This manual will help you keep abreast with many of the exciting features . This manual contains important safe measurements and correct operational information, so please read all the information carefully before use in order to avoid any damage, 1.
FRONT PANEL 1 1 3 2 1. POWER ON/OFF 2. USB JACK 3, Scart cable ,CHANNEL DOWN/CHANNWL UP REAR PANEL 1 2 3 4 5 1. RF SIGNAL INPUT 2.,RF SIGNAL OUTPUT 3. COAXIAL JACK 4. TV/ SCART 5. VCR SCART 6. HDMI 7.
How to connect Please connect TV set and set top box through HDMI cable or Scart cable , in our rear panel there are 2 Scart connectors and 1 HDMI connector . Please insert one side of the power adapter into the to DC Jack and the other side into the AC outlet. 2.
button function button function power turn on/off the device fav.
3. Welcome Page When turning the power on for the first time, the welcome page will be shown as below: 4. Installation Gudie (1) Press [CH+/CH-] key to move highlight. (2) Press [VOL+/VOL-] key to select the item (3) Move highlight to [Channel Search] and press [OK] key to begin the auto scan. (4) Press [Exit] key to exit menu. 5.
(3) Press the color key to execute the corresponding functions in “ALL TV”. 5.1.1 Move (1) Press [CH+/CH-] key to move the highlight and press [RED] key to make a mark. There will be a “moving mark” in the right side of the selected channel as above. (2) Press [CH+/CH-] key to move the selected channel to the position that you want to place. And press [RED] key to confirm your decision. 5.1.
make a favorite mark in the left side of the selected Favorite group. (3) Move the highlight to [Disable] to press [OK] key to cancel the existing favorite mark. (4) After marking, pressing [Exit] key to go back to “ALL TV”; there will be a favorite mark beside the marked channel. 5.1.6 Rename In “ALL TV” menu, press [CH-/CH+] key to move the highlight and press [GO TO] key to open the “Rename” window. then use the numeric key on the RC to set the TV name. 5.
Press [VOL-/VOL+] key to select “ Picture “program Aspect Ratio Press [VOL-/VOL+] key to change option item and press [ OK] key to confirm the selection. Resolution Press [VOL-/VOL+] key to change option item and press [ OK] key to confirm the selection. TV Format Press [VOL-/VOL+] key to change option item and press [ OK] key to confirm the selection. Video Output Press [VOL-/VOL+] key to change option item and press [ OK] key to confirm the selection. 7.
“Antenna Power” ON/OFF (a) If you can scan channel by adjusting “Frequency Channel” number and press [OK] key to start scanning (b)If you scan channel by Frequency(MHz), “Frequency” and “Bandwidth” are available to adjust. When you complete your modification, and press [OK] key, then it will begin to scan. (5) Press [Exit] key to exit the scanning. 8.
OSD Language Press [VOL-/VOL+] key to choose the language Subtitle Language Press [VOL-/VOL+] key to choose TV subtitle Language Audio Language Press [VOL-/VOL+] key to choose audio language Digital Audio Press [VOL-/VOL+] key to choose digital audio output PCM/RAM (3) Press [Exit] key to exit the Opito 10.
11. USB USB menu will be disabled when the USB device is unplugged. Media Player List will not be saved after unplugging USB and/or going to standby and power off. NOTE: The USB memory stick should be plug in the unit directly. USB extension cable should not be used to avoid failing of data transferring and interference caused. (1)Press [MENU] key to display MAIN MENU (2)Press [VOL-/VOL+] key to select “USB“ program 11.
Press [EXIT] key to return up Floder 11.2 Photo configure Press [CH-/CH+] key to move the cursor and Press [OK] enter the “Photo configure” Press [CH-/CH+] and [VOL-/VOL+] key to adjust optional item of “Slide Time” ,”Slide Mode” ”Aspect Ratio” 11.3 Movie configure Press [CH-/CH+] key to move the cursor and Press [OK] enter the “Movie configure” Press [CH-/CH+] and [VOL-/VOL+] key to adjust optional item of “Aspect Ratio” ,”Subtitle Specific” ”Subtitle BackGround”,” Subtitle FontColor” 11.
there are two methods to update firmware, as following: Select to update the firmware via a USB stick 1) Copy the new firmware to the root directory of a USB stick, and connect it to the USB HOST port of the player then press ENTER to confirm 2) Input password “666666” on main menu, system can update firmware automatically 3 Please restart STB after softeware upgrade complete 100% ） 13. REC Press [ press [ ] key to start recording ] key to stop recording 14. PVR RECORD 14.
15.Specifications Multimedia playback Connector PVR HD DTV Specification Input Frequency Range Input Impedance Active Ant Power Input Signal Level Waveform Bandwidth Demodulation FFT SIZE Code Rate Guard Intervals Video Bandwidth Video Impedance Video Voltage Level Audio Freq. Range Audio Impedance Audio Voltage Level Input Voltage Consumption Temperature Humidity Playback in different video and audio format USB2.0 host HDMI1.
16. Troubleshooting If you encounter problems when using this unit, check the following points before requesting service. Problem No Power Buttons do not work The player does not respond to the remote control No Picture No sound or distorted sound Solution Please: Confirm that you have an appropriate power source Check if all connections between wall outlet and power supply, and power supply and the player are correct.
