Blower User Manual

ManualsBrandsLennox Hearth ManualsBlower775202M

AIR CIRCULATION BLOWER KIT

MODEL VINT-TET BLWR, CAT. NO. 75194

INSTALLATION INSTRUCTIONS FOR AN AIR CIRCULATION

BLOWER KIT FOR USE WITH THE VINTAGE™ 27 GAS STOVE

775202M

Rev. A, 01/2011

LENNOX HEARTH PRODUCTS

KITS AND ACCESSORIES

KIT CONTENTS

1 ea. Blower Assembly (item #1)

2 ea. Washers, #10 (item #2)

2 ea. Nuts, 10-24 Nylock (item #3)

1 ea. Instruction Sheet

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

TURN OFF THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE

PROCEEDING.

INSTALLATION INSTRUCTIONS

Step 1. Using an allen wrench, remove socket head screw A that secures the

heat shield to the bottom of the stove. See Figure 2.

Step 2. Using pliers, twist and break off section B of the heat shield (shown

as hatched section B in Figure 2). Discard this piece after removing.

Figure 1 - Kit Contents

Figure 2

TOOLS NEEDED

5/32” Allen Wrench Or T-Handle Wrench

3/8” End Wrench

Pliers

GENERAL INFORMATION

This optional 150-CFM blower for the Vintage gas stove provides variable

speed control, thermal activation and forced air circulation of the warm air

into the room.

If you encounter any problems, need clariﬁcation of these instructions or are

not qualiﬁed to properly install this kit, contact you local distributor or dealer.

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPERA-

TION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE

INSTRUCTIONS.

Heat Shield

Stove Bottom

Stove Back

2. Remove Section B

and Discard

1. Remove

Screw A

Summary of content (4 pages)

PAGE 1
LENNOX HEARTH PRODUCTS KITS AND ACCESSORIES 775202M Rev. A, 01/2011 AIR CIRCULATION BLOWER kit MODEL VINT-TET BLWR, CAT. NO. 75194 INSTALLATION INSTRUCTIONS FOR an AIR CIRCULATION BLOWER KIT for use with the VINTAGE™ 27 GAS STOVE KIT CONTENTS TURN OFF THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE PROCEEDING. 1 ea. Blower Assembly (item #1) 2 ea. Washers, #10 (item #2) 2 ea. Nuts, 10-24 Nylock (item #3) 1 ea. Instruction Sheet Installation Instructions Step 1.
PAGE 2
Step 3. Remove the blower from the box and unwrap it. The blower has a rubber grommeted hole at each end (see Figure 3). Position the blower under the stove so the grommets are up and the blower control knob is at the left side (the left side is determined by standing in front of the stove looking at it). The grommeted holes slide over the two threaded studs located at the bottom rear of stove. See Figures 3 and 4. Step 4.
PAGE 3
Blower Operation The blower will come on when the stove is up to temperature and shut off when the stove cools. The blower control knob must be turned “ON” for the blower to operate (see Figure 6). Blower Control Knob - The highest blower speed is obtained by turning the control knob clockwise until it clicks “ON.” Continue to rotate the knob clockwise for a lower speed. To turn off, rotate the knob counterclockwise until it clicks “OFF.
PAGE 4
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. 4 Printed in U.S.A. © 2010 Lennox Hearth Products P/N 775202M REV.