ThinkCentre User Guide Machine Types: 1562, 1565, 1662, 1663, 1765, 1766, 2011, 2110, 2111, and 2112
Note: Before using this information and the product it supports, be sure to read and understand the “Important safety information” on page v and Appendix A “Notices” on page 123. Third Edition (September 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Important safety information . . . . . . v Service and upgrades . . . . . . Static electricity prevention . . . . Power cords and power adapters . Extension cords and related devices Plugs and outlets. . . . . . . . External devices . . . . . . . . Heat and product ventilation . . . Operating environment . . . . . Modem safety information . . . . Laser compliance statement . . . Power supply statement . . . . . Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the rear fan assembly . . . . . Replacing the front audio and USB assembly . . . . . . . . . . . . . . Replacing the internal speaker. . . . . . Replacing the thermal sensor . . . . . . Replacing the cover presence switch . . . Replacing the WiFi units . . . . . . . . Installing or removing the rear WiFi antenna Installing or removing the front WiFi antenna Replacing the keyboard or mouse . . . . Completing the parts replacement . . . . . 60 . . . . . . . . .
Purchasing additional services . . . . . . Appendix A. Notices . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . Appendix B. Regulatory information . . . . . . . . . . . . . Export classification notice . . . . . . . Electronic emissions notices . . . . . . Federal Communications Commission Declaration of Conformity . . . . . Additional regulatory information . . . . 123 124 125 . . . . . . 125 125 . . . . . . 125 127 Appendix C. WEEE and recycling information . . . . . . . . . . . . .
iv ThinkCentre User Guide
Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the information in this section and the safety information in the Safety, Warranty, and Setup Guide that you received with this product. Reading and understanding this safety information reduces the risk of personal injury and damage to your product.
or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: • Limit your movement. Movement can cause static electricity to build up around you. • Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry.
Plugs and outlets If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement. Do not share an electrical outlet with other home or commercial appliances that draw large amounts of electricity; otherwise, unstable voltage might damage your computer, data, or attached devices.
For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer: • Keep the cover closed whenever the computer is plugged in. • Regularly inspect the outside of the computer for dust accumulation. • Remove dust from vents and any perforations in the bezel. More frequent cleanings might be required for computers in dusty or high-traffic areas. • Do not restrict or block any ventilation openings.
Laser compliance statement CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
x ThinkCentre User Guide
Chapter 1. Product overview This chapter provides information about the computer features, specifications, software programs provided by Lenovo, and locations of connectors, components, parts on the system board, and internal drives. Features This section introduces the computer features. The information covers a variety of models.
• Internal speaker (installed in some models) Connectivity • 100/1000 Mbps integrated Ethernet controller • IEEE 1394 adapter (installed in some models) System management features • Ability to store power-on self-test (POST) hardware test results • Desktop Management Interface (DMI) Desktop Management Interface provides a common path for users to access information about all aspects of a computer, including processor type, installation date, attached printers and other peripherals, power sources, and mainte
Input/Output (I/O) features • 9-pin serial port (one standard and one optional) • DisplayPort connector (one standard and one optional) • Eight Universal Serial Bus (USB) connectors (two on the front panel and six on the rear panel) • One Ethernet connector • One Personal System/2 (PS/2) keyboard connector (optional) • One PS/2 mouse connector (optional) • One VGA monitor connector • Three audio connectors on the rear panel (audio line-in connector, audio line-out connector, and microphone connector) • Two
Preinstalled software programs Your computer is preinstalled with software programs to help you work more easily and securely. For more information, see “Lenovo programs” on page 5. Preinstalled operating system Your computer is preinstalled with one of the following operating systems: • Microsoft Windows 7 operating system • Microsoft Windows 8 operating system Operating system(s), certified or tested for compatibility1 (varies by model type) • Linux® • Microsoft Windows XP Professional SP 3 1.
Specifications This section lists the physical specifications for your computer. Dimensions Width: 175 mm (6.89 inches) Height: 414 mm (16.30 inches) Depth: 442 mm (17.40 inches) Weight Maximum configuration as shipped: 11 kg (24.
Note: If a program icon in the Lenovo ThinkVantage Tools program navigation window is dimmed, it indicates that you need to install the program manually. To install the program manually, double-click the program icon. Then, follow the instructions on the screen. When the installation process completes, the program icon will be activated. Table 1.
Table 2. Programs in Control Panel (continued) Program Control Panel section Green text in Control Panel SimpleTap Programs Lenovo - SimpleTap System Update System and Security Lenovo - Update and Drivers View Management Utility System and Security Lenovo View Management Utility Note: Depending on your computer model, some of the programs might not be available.
different devices such as personal computers, smart phones, or tablets. For more information about the Lenovo Cloud Storage program, go to http://www.lenovo.com/cloud. • Lenovo Companion Through the Lenovo Companion program, you can get the information about the accessories for your computer, view bolgs and articles about your computer, and check for other recommended programs.
– Click the red SimpleTap launch point on the desktop. The red launch point is available on the desktop after you have launched the SimpleTap program for the first time. – Press the blue ThinkVantage button if your keyboard has one. Note: The SimpleTap program is only available on certain models preinstalled with the Windows 7 operating system. If your Windows 7 model is not preinstalled with the SimpleTap program, you can download it from http://www.lenovo.com/support.
1 Hard disk drive activity indicator 5 USB 2.0 connector (USB port 1) 2 Power indicator 6 Headphone connector 3 Power switch 7 Microphone connector 4 Optical drive eject/close button 8 USB 2.0 connector (USB port 2) Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 10 shows the locations of the connectors on the rear of your computer.
Connector Description Audio line-in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable is connected between the audio line-out connector of the device and the audio line-in connector of the computer.
Locating components Figure 3 “Component locations” on page 12 shows the locations of the various components in your computer. To remove the computer cover, see “Removing the computer cover” on page 34. Figure 3.
Locating parts on the system board Figure 4 “System board part locations” on page 13 shows the locations of the parts on the system board. Figure 4.
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.
Machine type and model label The machine type and model label identifies your computer. When you contact Lenovo for help, the machine type and model information helps support technicians to identify your computer and provide faster service. The following is a sample of the machine type and model label. Figure 6. Machine type and model label Chapter 1.
16 ThinkCentre User Guide
Chapter 2. Using your computer This chapter provides information on using some of the computer components. Frequently asked questions The following are a few tips that will help you optimize the use of your computer. Can I get my user guide in another language? The user guide is available in various languages on the Lenovo Support Web site at: http://www.lenovo.com/ThinkCentreUserGuides Where are my recovery discs? Lenovo provides a program that enables you to create recovery discs.
Using the keyboard Depending on your model, your computer comes with either a standard keyboard or a fingerprint reader keyboard. The Microsoft Windows shortcut keys are provided on both keyboard types.
Using the wheel mouse The wheel mouse has the following controls: 1 Primary mouse button Use this button to select or start a program or menu item. 2 Wheel Use the wheel to control the scrolling action of the mouse. The direction in which you rotate the wheel controls the direction of the scrolling action. 3 Secondary mouse button Use this button to display a menu for the active program, icon, or object.
1. From the Windows desktop, click Start ➙ Control Panel ➙ Appearance and Personalization. 2. In the Taskbar and Start Menu section, click Customize icons on the taskbar. 3. Click Turn system icons on or off and change the volume behaviors from Off to On. 4. Click OK to save the new settings. To add the volume icon to the taskbar on the Windows 8 operating system, do the following: 1. Open Control Panel, and click Appearance and Personalization. 2.
• Do not write or stick paper on the disc. • Do not scratch or mark the disc. • Do not place or store the disc in direct sunlight. • Do not use benzene, thinners, or other cleaners to clean the disc. • Do not drop or bend the disc. • Do not insert damaged discs into the drive. Warped, scratched, or dirty discs can damage the drive. Playing a CD or DVD If your computer comes with a DVD drive, you can listen to audio CDs or watch DVD movies. To play a CD or DVD, do the following: 1.
22 ThinkCentre User Guide
Chapter 3. You and your computer This chapter provides information about accessibility, comfort, and relocating your computer to other countries or regions. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 inches), and position it so you can view it without having to twist your body. Also, position other equipment you use regularly, such as the telephone or a mouse, within easy reach. Glare and lighting Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources.
Registering your computer When you register your computer, information is entered into a database, which enables Lenovo to contact you in case of a recall or other severe problem. After you register your computer with Lenovo, you will receive quicker service when you call Lenovo for help. In addition, some locations offer extended privileges and services to registered users. To register your computer with Lenovo, do one of the following: • Go to http://www.lenovo.
Replacement power cords If you relocate your computer to a country or region that uses an electrical outlet style different from the type you are currently using, you will have to purchase either electrical plug adapters or new power cords. You can order power cords directly from Lenovo. For power cord information and part numbers, go to: http://www.lenovo.
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use. Security features The following security features are available on your computer: • Computrace Agent software embedded in firmware The Computrace Agent software is an IT asset management and computer theft recovery solution. The software detects if changes have been made on the computer, such as hardware, software, or the computer call-in location.
Locking the computer cover Locking the computer cover helps prevent unauthorized people from gaining access to the inside of your computer. Your computer comes with a padlock loop so that the computer cover cannot be removed when a padlock is installed. Figure 7.
Attaching a cable lock A cable lock can be used to secure devices, such as the keyboard and the mouse, by locking the device cables to your computer. The cable lock attaches to the cable lock slots on the rear of your computer. See “Locating connectors on the rear of your computer” on page 10. To install a cable lock, do the following: 1. Insert the clip 1 into the cable lock slot 4 . 2. Pull the cables you want to lock through the dents in the cable lock. 3.
Attaching an integrated cable lock An integrated cable lock, sometimes referred to as the Kensington lock, can be used to secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to the integrated cable lock slot at the rear of your computer and is operated with a key. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many notebook computers.
• Administrator Password: Setting an Administrator Password deters unauthorized users from changing configuration settings. If you are responsible for maintaining the configuration settings of several computers, you might want to set an Administrator Password. For more information, see “Administrator Password” on page 90. You do not have to set any passwords to use your computer. However, using passwords improves computing security.
For more information about how to use your antivirus software, refer to the help system of your antivirus software.
Chapter 5. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage computer components and parts.
Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To remove the computer cover, do the following: 1. Remove any media from the drives and turn off all attached devices and the computer. 2.
Removing and reinstalling the front bezel Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3.
This section provides instructions on how to install or replace a PCI card. Your computer has two standard PCI card slots, one PCI Express x1 card slot, and one PCI Express x16 graphics card slot. To install or replace a PCI card, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. At the rear of the computer, press the release button 1 to open the card latch 2 . Figure 12.
Figure 13. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. b. If the card is held in place by a retaining latch, press the card retaining latch 1 as shown to disengage the latch. Grasp the card and gently pull it out of the slot. 5. Remove the new PCI card from its static-protective package. 6. Install the new card into the appropriate slot on the system board.
7. Pivot the card latch to the closed position to secure the PCI card. Figure 14. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79. Installing or replacing a memory module Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v.
UDIMM DIMM 1 DIMM 2 DIMM 3 DIMM 4 One UDIMM X Two UDIMMs X, 1 X, 2 X, 2 Three UDIMMs X, 3 X, 1 Four UDIMMs X, 3 X, 1 X, 4 X, 2 To install or replace a memory module, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Lay the computer on its side for easier access to the system board. 4. Locate the memory slots. See “Locating parts on the system board” on page 13.
• If you are installing a memory module, open the retaining clips of the memory slot into which you want to install the memory module. Figure 16. Opening the retaining clips 7. Position the new memory module over the memory slot. Ensure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 17. Installing a memory module 8.
1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 35. 4. Depending on whether you are installing or replacing an optical drive, do one of the following: • If you are installing a secondary optical drive, remove the plastic panel in the front bezel for the drive bay you want to use.
6. Slide the new optical drive into the drive bay from the front of the computer until the optical drive snaps into position. Figure 20. Installing the optical drive 7. Connect the signal cable and the power cable to the new optical drive. Figure 21. Connecting the optical drive 8. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 35. What to do next: • To work with another piece of hardware, go to the appropriate section.
This section provides instructions on how to install or replace the card reader. Note: The card reader is only available in some models. For new installation, see “Installing the card reader” on page 43. For replacement, see “Replacing the card reader” on page 45. Installing the card reader To install the card reader, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
7. Slide the card reader with retainer into the card reader drive bay until it snaps into position. Figure 24. Installing the card reader 8. Connect the card reader cable to Front USB connector 2 on the system board. See “Locating parts on the system board” on page 13. 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 35. Note: You might have to remove the card reader cover 2 from the front bezel.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79. Replacing the card reader To replace the card reader, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover.
8. Slide the new card reader into the drive bay until it snaps into position. Figure 28. Installing the card reader 9. Reconnect the card reader cable to Front USB connector 2 on the system board. See “Locating parts on the system board” on page 13. 10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 35. 11. To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
4. Remove the old battery. Figure 29. Removing the old battery 5. Install a new battery. Figure 30. Installing a new battery 6. Reinstall the computer cover and connect the cables. See “Completing the parts replacement” on page 79. Note: When the computer is turned on for the first time after replacing the battery, an error message might be displayed. This is normal after replacing the battery. 7. Turn on the computer and all attached devices. 8.
Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. To replace the power supply assembly, do the following: 1.
5. Lay the computer on its side and remove the four screws at the rear of the chassis that secure the power supply assembly. Figure 31. Removing the screws for the power supply assembly 6. Slide the power supply assembly to the front of the computer and then lift it out of the chassis. 7. Ensure that the new power supply assembly is the correct replacement. 8. Install the new power supply assembly into the chassis so that the screw holes in the power supply assembly align with those in the chassis. 9.
To replace the heat sink and fan assembly, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Lay the computer on its side for easier access to the system board. 4. Locate the heat sink and fan assembly. See “Locating parts on the system board” on page 13. 5. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system board.
a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 . b. Partially tighten screw 3 , then fully tighten screw 4 , and then fully tighten screw 3 . 10. Connect the heat sink and fan assembly cable to the microprocessor fan connector on the system board. See “Locating parts on the system board” on page 13. What to do next: • To work with another piece of hardware, go to the appropriate section.
6. Lift the small handle 1 to release the microprocessor 2 secured on the system board. Figure 33. Accessing the microprocessor 7. Lift the microprocessor straight up and out of the microprocessor socket. Figure 34. Removing the microprocessor Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can look for the small triangle 1 on one corner of the microprocessor.
c. Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom. d. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. 8. Ensure that the small handle is in the raised position. 9. Remove the protective cover that protects the gold contacts of the new microprocessor. 10.
Figure 35. Removing the primary hard disk drive 6. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 7. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 36.
8. Slide the new hard disk drive into the drive cage until it snaps into position. Figure 37. Installing the primary hard disk drive 9. Connect the signal cable and the power cable to the new hard disk drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
5. Pull the blue handle to release and remove the hard disk drive from the hard disk drive cage. Figure 38. Removing the secondary hard disk drive 6. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 7. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 39.
8. Slide the new hard disk drive into the hard disk drive cage until it snaps into position. Figure 40. Installing the secondary hard disk drive 9. Connect the signal cable and the power cable to the new hard disk drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
1. Install the solid-state drive into the storage converter. Then, install the four screws to secure the solid-state drive to the storage converter. Figure 41. Installing the solid-state drive into the storage converter 2. To install the solid-state drive with the storage converter into the 3.5-inch hard disk drive bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the storage converter. Figure 42.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79. Replacing the front fan assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the front fan assembly. Note: The front fan assembly is only available in some models.
7. Pull the tips of the rubber mounts until the front fan assembly is secured in place. Figure 44. Installing the front fan assembly 8. Connect the front fan assembly cable to the power fan connector on the system board. 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 35. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis. Note: The new rear fan assembly will have four new rubber mounts attached. Figure 45. Removing the rear fan assembly 6. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in the chassis and push the rubber mounts through the holes. Chapter 5.
7. Pull the tips of the rubber mounts until the rear fan assembly is secured in place. Figure 46. Installing the rear fan assembly 8. Connect the rear fan assembly cable to the system fan connector on the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
5. Disconnect the front audio and USB assembly cables from the system board. See “Locating parts on the system board” on page 13. Note: Ensure that you note the locations of the cables when you disconnect the cables from the system board. 6. Remove the screw that secures the front audio and USB assembly bracket to the chassis to remove the bracket from the chassis. Figure 47. Removing the screw that secures the front audio and USB assembly to the chassis 7.
This section provides instructions on how to replace the internal speaker. Note: The internal speaker is only available on some models. To replace the internal speaker, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Locate the internal speaker connector on the system board. See “Locating parts on the system board” on page 13. 4.
6. Position the new internal speaker into the four metal clips 1 and push the internal speaker toward the left until it is secured in place. Figure 49. Installing a new internal speaker 7. Connect the internal speaker cable to the system board. See “Locating parts on the system board” on page 13. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
6. From inside the chassis, pivot the upper retaining clip 1 that secures the plastic holder of the thermal sensor downward and then push the clip outward to release the clip. Then disengage the plastic holder holding the thermal sensor from the chassis. Figure 50. Removing the thermal sensor 7. Pull the entire thermal sensor out of the chassis.
8. Insert the connector and cable of the new thermal sensor into the lower hole 1 in the chassis. Then align the two tabs on the plastic holder holding the thermal sensor with the two holes 1 and 2 in the chassis, and push the plastic holder until it snaps into position. Figure 51. Installing the new thermal sensor 9. Reconnect the thermal sensor cable to the system board. See “Locating parts on the system board” on page 13. 10. Reinstall the front bezel.
6. Remove the screw that secures the cover presence switch and remove the cover presence switch from the chassis. Figure 52.
7. Position the new cover presence switch so that the screw hole in the cover presence switch is aligned with the corresponding hole in the chassis. Then install the screw to secure the cover presence switch to the chassis. Figure 53. Installing the new cover presence switch 8. Reconnect the cover presence switch cable to the system board. See “Locating parts on the system board” on page 13. 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 35.
Removing the WiFi adapter card To remove a WiFi adapter card, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. At the rear of the computer, press the release button 1 to open the PCI card latch 2 . Figure 54.
4. Grasp the WiFi adapter card that is currently installed and gently pull it out of the slot. Figure 55. Removing the WiFi adapter card Note: The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. Removing the WiFi card module To remove the WiFi card module, do the following: 1. Remove the WiFi adapter card from the computer, and then disconnect the front and rear WiFi antenna cables from the WiFi card module.
2. Remove the two screws that secure the WiFi card module to the WiFi adapter card. Figure 57. Removing the screws that secure the WiFi card module 3. Pull the WiFi card module out of the mini PCI Express slot to remove it from the WiFi adapter card. Figure 58.
1. Insert the WiFi card module into the mini PCI Express slot, and then install the two screws to secure the WiFi card module to the WiFi adapter card. Figure 59. Installing the WiFi card module Chapter 5.
2. Connect the front antenna cable and rear antenna cable to the WiFi card module. Figure 60. Installing the WiFi antenna cables 3. Install the WiFi adapter card into the PCI Express x1 slot on the system board. See “Locating parts on the system board” on page 13. 4. Pivot the card latch to the closed position to secure the WiFi adapter card. Figure 61. Installing the WiFi adapter card What to do next: • To work with another piece of hardware, go to the appropriate section.
Installing or removing the rear WiFi antenna Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to install or remove the rear WiFi antenna. Installing the rear WiFi antenna To install the rear WiFi antenna, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2.
3. Hold the thicker end of the rear WiFi antenna and unscrew the WiFi antenna from the rear of the computer. Figure 63. Removing the rear WiFi antenna What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79.
Figure 64. Peeling off the paper that protects the stickers 5. Stick the front antenna to the front panel as shown. Then insert the front antenna cable through the hole in the front panel. Figure 65. Installing the front WiFi antenna 6. Connect the front antenna cable to the WiFi card module. Chapter 5.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 79. Removing the front WiFi antenna To remove the front WiFi antenna, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Remove the front bezel.
3. Disconnect the old keyboard cable or mouse cable from the computer. 4. Connect a new keyboard or mouse to one of the USB connectors on the computer. Depending on where you want to connect the new keyboard or mouse, see “Locating connectors, controls, and indicators on the front of your computer” on page 9 or “Locating connectors on the rear of your computer” on page 10. Figure 67.
4. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails on the chassis. Then, push the cover to the front of the computer until it snaps into position. Figure 68. Reinstalling the computer cover 5. Install the screws to secure the computer cover. 6. If there is a padlock available, lock the computer cover. See “Locking the computer cover” on page 28. 7. If there is an integrated cable lock available, lock the computer.
Chapter 6. Recovery information This chapter provides information about the recovery solutions provided by Lenovo.
Creating recovery media This section provides instructions on how to create recovery media on different operating systems. Note: On the Windows 7 operating system, you can create recovery media using discs or external USB storage devices. To create recovery media on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media.
1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click the Launch advanced Rescue and Recovery arrow. 3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation.
2. Turn on your computer. When you see the logo screen, press Enter, and then press F11 to enter the Rescue and Recovery workspace. 3. If you have set a Rescue and Recovery password, type your password when prompted. The Rescue and Recovery workspace opens after a short delay. Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 86. 4.
2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window opens, release the F12 key. 3. In the Please select boot device window, select the USB hard disk drive as the first boot device and press Enter. The rescue medium starts. When the rescue medium starts, the Rescue and Recovery workspace opens. The help information for each feature is available from the Rescue and Recovery workspace. Follow the instructions to complete the recovery process.
Reinstalling software programs If a software program you installed on your computer is not working correctly, you might need to remove and reinstall it. Reinstalling overwrites the existing programs files and usually fixes any problems that you might have had with that program. To remove a program in your system, see Microsoft Windows help system for detailed information. To reinstall the program, do one of the following: Note: The method of reinstalling a program varies from program to program.
Recovery information for the Windows 8 operating system This section provides information about the recovery solutions provided on computers preinstalled with the Windows 8 operating system. Refreshing your computer If your computer does not perform well and the problem might be caused by a recently installed program, you can refresh your computer without losing your personal files or changing your settings.
88 ThinkCentre User Guide
Chapter 7. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Ensure that your computer is turned off. 2. Repeatedly press and release the F1 key when turning on the computer.
• Administrator Password • Hard Disk Password You do not have to set any passwords to use your computer. However, using passwords improves computing security. If you decide to set any passwords, read the following sections. Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised.
2. From the Setup Utility program main menu, select Security. 3. Depending on the password type, select Set Power-On Password, Set Administrator Password, or Hard Disk Password. 4. Follow the instructions on the right side of the screen to set, change, or delete a password. Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Password considerations” on page 90.
Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want. Selecting a temporary startup device Use this procedure to select a temporary startup device. Note: Not all discs and hard disk drives are bootable. 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window displays, release the F12 key.
1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ Automatic Power On, and press Enter. 3. Select Wake Up on Alarm and press Enter. Then follow the instructions on the screen. 4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm the exit. • Enabling the after power loss feature The after power loss feature enables your computer to wake up when the power supply resumes after a sudden loss of electricity.
2. From the Setup Utility program main menu, select Power. 3. Select Intelligent Cooling Engine (ICE). The Intelligent Cooling Engine (ICE) window is displayed. 4. Select ICE Thermal Alert. The ICE Thermal Alert window is displayed. 5. Select Enabled or Disabled as desired. 6. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program” on page 94.
Chapter 8. Updating system programs This chapter provides information about updating the POST and BIOS, and how to recover from a POST and BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. System programs include the POST, the BIOS, and the Setup Utility program. The POST is a set of tests and procedures that are performed each time you turn on your computer.
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure. To update (flash) the BIOS from your operating system, do the following: 1. Go to http://www.lenovo.com/support. 2. Do the following to locate the downloadable files for your machine type: a. In the Enter a product number field, type your machine type and click Go.
Chapter 9. Preventing problems This chapter provides information that can help you avoid common problems and keep your computer running smoothly. Keeping your computer current In some situations you may find it necessary to have the most current software programs, device drivers, or operating system. This section explains how to get the latest updates for your computer.
Using System Update The System Update program helps you keep the software on your computer up-to-date. Update packages are stored on Lenovo servers and can be downloaded from the Lenovo Support Web site. Update packages can contain applications, device drivers, BIOS flashes, or software updates.
Cleaning your computer It is a good practice to clean your computer periodically to protect the surfaces and ensure trouble-free operation. CAUTION: Be sure to turn off the computer and monitor power switches before cleaning the computer and monitor screen. Computer Use only mild cleaning solutions and a damp cloth to clean the painted surfaces of the computer. Keyboard To clean your computer keyboard, do the following: 1. Apply some isopropyl rubbing alcohol to a soft, dust-free cloth. 2.
Many computer supply stores carry the special cleaning fluids for displays. Use cleaning fluids developed for LCD displays only. First apply the fluid to a lint-free, soft cloth, then clean the LCD display. Some computer supply stores carry pre-moistened towelettes for LCD maintenance. Cleaning a glass-screen surface To clean a glass-screen surface, wipe it gently with a soft, dry cloth, or blow on the screen to remove grit and other loose particles.
Chapter 10. Troubleshooting and diagnostics This chapter provides information about diagnosing and troubleshooting computer problems. If your computer problem is not described here, see Chapter 11 “Getting information, help, and service” on page 119 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problems. Note: If you cannot correct the problem, have the computer serviced.
Symptom Action The operating system does not start. Verify that: The computer beeps multiple times before the operating system starts. Verify that no keys are stuck. • The startup sequence includes the device where the operating system resides. Usually, the operating system is on the hard disk drive. For more information, see “Selecting a startup device” on page 92.
1. Remove the new hardware option or software. If you must remove the computer cover to remove a hardware option, ensure that you review and follow the electrical safety information provided with your computer. For your safety, do not operate the computer with the cover removed. 2. Run the diagnostic program to ensure that your computer is operating correctly. 3. Reinstall the new hardware option or software following the manufacturer's instructions.
Note: When external-speaker or headphone cables are attached to the audio connector, the internal speaker, if present, is disabled. In most cases, if an audio adapter is installed in one of the expansion slots, the audio function built into the system board is disabled; use the audio jacks on the adapter. • Ensure that the program you are running is designed for use in the Microsoft Windows operating system.
An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive Symptom: An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive. Actions: • If you have multiple CD or DVD drives installed (or a combination of CD and DVD drives), try inserting the disc into the other drive. In some cases, only one of the drives is connected to the audio subsystem.
Actions: • Restart the DVD player program. • Close any open files, turn off the computer, and then restart the computer. • Try a lower screen resolution or color depth. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 119. DVD movie will not play Symptom: DVD movie will not play. Actions: • Ensure that the disc surface is clean and not scratched.
• On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, ensure that the DVD disc is in the drive labeled “DVD”. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 119. Intermittent problems Symptom: A problem occurs only occasionally and is difficult to repeat.
3. Click Devices and Printers. 4. Double-click USB Enhanced Performance Keyboard. The USB Enhanced Performance Keyboard Customization program starts. If these actions do not correct the problem, have the computer and keyboard serviced. See Chapter 11 “Getting information, help, and service” on page 119 for details. The mouse or pointing device does not work Symptom: The mouse or pointing device does not work.
Action: If the Transceiver Communications LED is not on, reconnect the transceiver and the keyboard. Monitor problems Note: Many monitors have status-indicator lights and built-in controls for adjusting brightness, contrast, width, height, and other picture adjustments. However, the controls vary from monitor type to monitor type. For information about the status lights and using the controls, refer to the documentation that comes with your monitor.
Actions: • The monitor might be operating in a low-refresh rate display mode. Set the monitor to the highest, noninterlaced refresh rate supported by your monitor and the video controller in your computer. Attention: Using a resolution or refresh rate that is not supported by your monitor might damage it. Check the documentation that comes with your monitor to verify the supported refresh rates. • The monitor might be affected by interference from nearby equipment.
Ethernet problems For Ethernet problems, select your symptom from the following list: • “Your computer cannot connect to the network” on page 111 • “The adapter stops working for no apparent reason” on page 111 • “If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection fails or errors occur” on page 112 • “If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps.
Action: The network driver files may be corrupt or missing. Update the driver by referring to the “Solution” description for the procedure to ensure that the correct device driver is installed. The Wake on LAN feature is not working Symptom: The Wake on LAN (WOL) feature is not working. Actions: • Ensure that WOL is enabled in the BIOS Setup Utility program. • If it is, check with your LAN administrator for the necessary settings.
Bluetooth problem Symptom: Sound does not come from the Bluetooth headset or headphone but comes from the local speaker even though the headset or headphone is connected using the Headset profile or AV profile. Action: Do the following: 1. Exit the application that uses the sound device (for example, Windows Media Player). 2. Open Control Panel. 3. Click Hardware and Sound ➙ Sound. 4. Select the Playback tab. 5.
– All external SCSI options are turned on. External SCSI options must be turned on before the computer is turned on. For more information, see your SCSI documentation. • Verify that the option and any required device drivers are installed correctly. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 119.
4. Click Clean up system files. 5. Click the More Options tab. 6. In the Programs and Features area, click the Clean up button. 7. A list of installed programs is displayed. Select the program that you want to remove. Click Uninstall/Change. • Clean out your Inbox, Sent Items, and Deleted Items folders from your e-mail application. The folder names and procedures vary depending on your e-mail application. If you need assistance, see the help system for your e-mail application.
Actions: Verify that: 1. The printer is turned on and is online. 2. Paper is loaded correctly. 3. The printer signal cable is securely connected to the correct parallel, serial, or USB connector on the computer. Note: Non-IEEE-approved printer signal cables might cause unpredictable problems. 1. Any device drivers and other software that came with the printer are correctly installed. 2. You have assigned the printer port correctly in your operating system, application program, or BIOS settings.
Actions: • Most software programs have built-in help systems that provide instructions for most tasks. If you are having difficulty performing a specific task within a software program, refer to the help system for that program. Help systems are typically accessible from a menu or button in the program, and frequently from the F1 key. • If you are having difficulty with the Windows operating system or one of its components, refer to the Windows help system. It is accessible from the Windows Start menu.
Lenovo Solution Center The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It combines diagnostic tests, system information collection, security status, and support information, along with hints and tips for maximum system performance. Notes: • The Lenovo Solution Center program can be downloaded from http://www.lenovo.com/diags. • If you are using other Windows operating system rather than Windows 7 and Windows 8, go to http://www.lenovo.
Chapter 11. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources You can use the information in this section to access useful resources relating to your computing needs. Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely.
• Access the online manuals for your products. • Access the Lenovo Limited Warranty. • Access troubleshooting and support information for your computer model and other supported products. • Find the service and support phone numbers for your country or region. • Find a Service Provider located near you. Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at: http://www.lenovo.
• Engineering Change management - There might be changes that are required after a product has been sold. Lenovo or your reseller will make selected Engineering Changes (ECs) that apply to your hardware available.
might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo Rescue and Recovery ThinkCentre ThinkVantage Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies. AMD is a trademark of Advance Micro Devices, Inc. Linux is a trademark of Linus Torvalds in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others.
Appendix B. Regulatory information Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed countries in the EAR E1 country list. Electronic emissions notices The following information refers to Lenovo personal computer machine types 1562, 1565, 1662, 1663, 1765, 1766, 2011, 2110, 2111, and 2112.
European Union - Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Japanese VCCI Class B statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Lenovo product service information for Taiwan Keyboard and mouse compliance statement for Taiwan Additional regulatory information For additional regulatory information, refer to the Regulatory Notice shipped with your computer.
128 ThinkCentre User Guide
Appendix C. WEEE and recycling information Important WEEE information The WEEE marking on Lenovo products applies to countries with WEEE and e-waste regulations (for example, European Directive 2002/96/EC, India E-Waste Management & Handling Rules, 2011). Appliances are labeled in accordance with local regulations concerning waste electrical and electronic equipment (WEEE). These regulations determine the framework for the return and recycling of used appliances as applicable within each geography.
Collecting and recycling a disused Lenovo computer or monitor If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of the company, you must do so in accordance with the Law for Promotion of Effective Utilization of Resources. Computers and monitors are categorized as industrial waste and should be properly disposed of by an industrial waste disposal contractor certified by a local government.
Battery recycling information for the European Union Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union.
132 ThinkCentre User Guide
Appendix D. Restriction of Hazardous Substances Directive (RoHS) China RoHS Turkish RoHS The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (EEE).
India RoHS RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
Appendix E. ENERGY STAR model information ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation.
136 ThinkCentre User Guide
Index A a rescue medium, creating and using Administrator, password 90 audio line-in connector 11 audio line-out connector 11 audio subsystem 1 B backup and recovery operations basic troubleshooting 101 battery, replacing 46 boot-block recovery 96 82 C cable lock, security 29–30 card reader, installing 42 card reader, replacing 45 changing password 90 startup device sequence 92 cleaning an optical mouse 99 CMOS, clearing 91 components, internal 12 computer cover removing 34 computer cover, reinstalling 7
installing solid-state drive 57 installing options memory module 38 PCI card 35 internal drives 1 internal speaker, replacing features 3 power supply assembly, replacing 47 power-on self-test (POST) 95 Power-On, Password 90 programs, updating system 95 purchasing additional services 121 63 R K keyboard connector keyboard, replacing 11 78 L Lenovo Solution Center 118 Lenovo ThinkVantage Tools 119 Lenovo Welcome 119 locating components 12 M media, creating and using recovery media memory module installi
recovering 81 solid-state drive, installing 57 solving recovery problems 86 starting the Setup Utility program startup device 92 sequence, changing 92 temporary, selecting 92 static-sensitive devices, handling system management 2 programs 95 system board connectors 13 locating parts 13 locations 13 memory module 38 89 33 T temporary startup device 92 the BIOS, updating (flashing) 95–96 thermal sensor, replacing 65 trademarks 124 troubleshooting, basic 101 troubleshooting, diagnostics 101 U updating (fla
140 ThinkCentre User Guide
