P1 Gen 3 / X1 Extreme Gen 3 User Guide
Read this first Before using this documentation and the product it supports, ensure that you read and understand the following: • Appendix A “Important safety information” on page 59 • Safety and Warranty Guide • Setup Guide First Edition (August 2020) © Copyright Lenovo 2020. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS35F-05925.
Contents About this documentation . . . . . . . . iii Chapter 1. Meet your computer . . . . . 1 Front . . . . . . . . . . . . . Base . . . . . . . . . . . . . Left . . . . . . . . . . . . . Right . . . . . . . . . . . . . Bottom . . . . . . . . . . . . Features and specifications . . . . Statement on USB transfer rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 4 5 6 7 8 Chapter 2. Get started with your computer . . . . . . . . . . . . . .
Wireless WAN card (for selected models) Memory module . . . . . . . . . . M.2 solid-state drive . . . . . . . . Coin-cell battery . . . . . . . . . . . . . . . . . . . . . . 45 47 49 51 Chapter 7. Help and support . . . . . 53 Frequently asked questions . . . . . Error messages . . . . . . . . . . Beep errors . . . . . . . . . . . Self-help resources . . . . . . . . Call Lenovo . . . . . . . . . . . Before you contact Lenovo . . . Lenovo Customer Support Center . Purchase additional services. . . . .
About this documentation • Illustrations in this documentation might look different from your product. • Depending on the model, some optional accessories, features, and software programs might not be available on your computer. • Depending on the version of operating systems and programs, some user interface instructions might not be applicable to your computer. • Documentation content is subject to change without notice.
iv P1 Gen 3 / X1 Extreme Gen 3 User Guide
Chapter 1.
1. Microphones* Capture or record sound. Emit infrared (IR) light. 2. Infrared LED* Note: Do not block the light-emitting diode (LED). Otherwise, the IR function might not work. • Take pictures or record videos by clicking Camera from the Start menu. The indicator next to the camera is on when the camera is in use. 3. Camera with IR function* • Log in to your computer with face authentication. See “Use face authentication (for selected models)” on page 33.
Base Press to turn on the computer or put the computer to sleep mode. To turn off the computer, open the Start menu, click Shut down. Power, and then select The indicator in the power button shows the system status of your computer. 1. Power button • Blinking for three times: The computer is initially connected to power. • On: The computer is on. • Off: The computer is off or in hibernation mode. • Blinking rapidly: The computer is entering sleep or hibernation mode.
Left 1. Power connector Connect to ac power through an ac power adapter. • Charge your computer. • Charge USB-C compatible devices with the output voltage and current of 5 V and 3 A. • Transfer data at Thunderbolt 3 speed, up to 40 Gbps. 2. Thunderbolt ™ 3 connectors (USB-C™) • Connect to an external display: – USB-C to VGA: 1900 x 1200 pixels, 60 Hz – USB-C to DP: 3840 x 2160 pixels, 60 Hz • Connect to USB-C accessories to help expand your computer functionality.
Right 1. Nano-SIM-card tray* Use the Nano Subscriber Identity Module (SIM) card to connect to a wirelessWAN network. See “Connect to a cellular network (for selected models)” on page 12. 2. Media-card slot Insert a flash media card for data access or storage. See “Use a media card” on page 26. 3. USB 3.2 connector Gen 1 4. Always On USB 3.2 connector Gen 1 Connect a USB-compatible device, such as a USB keyboard, USB mouse, USB storage device, or USB printer.
Bottom If the computer stops responding and you cannot turn it off by pressing the power button, reset your computer: 1. Emergency-reset hole 1. Disconnect your computer from ac power. 2. Insert a straightened paper clip into the hole to cut off power supply temporarily. 3. Connect your computer to ac power and then turn on your computer. 2. Speakers 6 Enable you to experience high-quality sound.
Features and specifications • Width: 361.8 mm (14.2 inches) • Depth: 245.7 mm (9.7 inches) Dimensions • Thickness: – Non-touch models: 18.4 mm (0.72 inches) – Touch models: 18.7 mm (0.
• Face authentication* • Fingerprint reader Security features • Password • Security-lock slot • ThinkShutter* • Trusted Platform Module (TPM) • Bluetooth Wireless features • Wireless LAN • Wireless WAN* Others • Camera* • Microphones * for selected models Statement on USB transfer rate Depending on many factors such as the processing capability of the host and peripheral devices, file attributes, and other factors related to system configuration and operating environments, the actual transfer rate us
Chapter 2. Get started with your computer Get started with Windows 10 Learn the basics of Windows 10 and start working with it right away. For more information about Windows 10, see the Windows help information. Windows account A user account is required to use the Windows operating system. It can either be a Windows user account or a Microsoft account. Windows user account When you start Windows for the first time, you are prompted to create a Windows user account.
Windows user interface 1. Account Change account settings, lock the computer, or sign out from the current account. 2. Documents Open the Documents folder, a default folder to save your received files. 3. Pictures Open the Pictures folder, a default folder to save your received pictures. 4. Settings Launch Settings. 5. Power Shut down, restart, or put the computer into sleep mode. 6. Start button Open the Start menu. 7.
• Use Windows Search. Launch an app • Open the Start menu and select the app you want to launch. • Use Windows Search. Windows label Your computer might have a Windows 10 Genuine Microsoft label affixed to its cover depending on the following factors: • Your geographic location • Edition of Windows 10 that is preinstalled Go to https://www.microsoft.com/en-us/howtotell/Hardware.aspx for illustrations of the various types of Genuine Microsoft labels.
Connect to a cellular network (for selected models) If your computer has a wireless wide area network (WAN) card and a nano-SIM card installed, you can connect to a cellular data network and get online using the cellular signal. Note: The cellular service is provided by authorized mobile service carriers in some countries or regions. You must have a cellular plan from a service carrier to connect to the cellular network. To establish a cellular connection: 1. Turn off the computer. 2.
• Look up warranty status (online). • Access User Guide and helpful articles. Notes: • The available features vary depending on the computer model. • Lenovo Vantage makes periodic updates of the features to keep improving your experience with your computer. The description of features might be different from that on your actual user interface. Interact with your computer Your computer provides you various ways to navigate the screen.
Switch the function of the F1–F12 keys between the standard function and special function printed as an icon on each key. When the Fn Lock indicator is on: • Press F1-F12 to use the standard function. • Press Fn+F1-F12 to use the special function. When the Fn Lock indicator is off: • Press Fn+F1-F12 to use the standard function. • Press F1-F12 to use the special function. Mute or unmute the speakers. When the key indicator is on, the speakers are muted.
Open the Snipping Tool program. Fn+Spacebar Switch between different keyboard backlight statuses if your computer supports keyboard backlight. Fn+B Equal the Break key on a conventional external keyboard. Fn+K Equal the ScrLK or Scroll Lock key on a conventional external keyboard. Fn+P Equal the Pause key on a conventional external keyboard. Fn+S Equal the SysRq key on a conventional external keyboard. Fn+4 Put the computer to sleep mode. To wake up the computer, press Fn or the power button.
Press to display a shortcut menu. 4. Middle button Press and hold the dotted middle button while applying pressure to the pointing stick in the vertical or horizontal direction. Then, you can scroll through the document, Web site, or apps. Disable the TrackPoint pointing device The TrackPoint pointing device is active by default. To disable the device: 1. Open the Start menu, and then click Settings ➙ Devices ➙ Mouse. 2. Follow the on-screen instructions to disable TrackPoint.
Press to select or open an item. You also can tap anywhere on the surface of the trackpad with one finger to perform the left-click action. 2. Right-click zone Press to display a shortcut menu. You also can tap anywhere on the surface of the trackpad with two fingers to perform the right-click action. Use the touch gestures Tap Tap anywhere on the trackpad with one finger to select or open an item. Two-finger tap Tap anywhere on the trackpad with two fingers to display a shortcut menu.
Swipe three fingers up Put three fingers on the trackpad and move them up to open the task view to see all your open windows. Swipe three fingers down Put three fingers on the trackpad and move them down to show the desktop. Notes: • When using two or more fingers, ensure that you position your fingers slightly apart. • Some gestures are not available if the last action was done from the TrackPoint pointing device. • Some gestures are only available when you are using certain apps.
Tap and hold Open a shortcut menu. Slide Scroll through items, such as lists, pages, and photos. Drag an item to the location you want Move an object. Move two fingers closer together Zoom out. Move two fingers farther apart Zoom in. Swipe in from the right edge Open the action center to see your notifications and quick actions. Chapter 2.
Swipe in from the left edge View all your open windows in task view. • Swipe downwards shortly from the top edge (for full-screened app or when your computer is in the tablet mode) Show a hidden title bar. • Swipe in from the top edge to the bottom edge (when your computer is in the tablet mode) Close the current app. Tips • Turn off the computer before cleaning the multi-touch screen.
Use the Cool and Quiet on lap feature The Cool and Quiet on lap feature helps cool down your computer when it becomes hot. Any extended contact with your body, even through clothing, could cause discomfort. If you prefer using your computer on the lap, it is recommended that you enable the Cool and Quiet on lap feature in UEFI BIOS: 1. Enter the UEFI BIOS menu. See “Enter the UEFI BIOS menu” on page 35. 2. Click Config and turn on the Cool and Quiet on lap mode switch.
• Open the Start menu, and then click Settings ➙ Devices ➙ Bluetooth & other devices ➙ Add Bluetooth or other device. In the Add a device window, click Wireless display or dock. Then, follow the instructions on the screen. • Click the action center icon in the Windows notification area and click Connect. Select the wireless display and follow the on-screen instructions. Set the display mode Press or and then select a display mode of your preference.
Pen overview 1 Top pen button: Hold the top pen button for at least three seconds to enable Bluetooth pairing on the pen.
Pair the pen 1. Enable Bluetooth pairing on the pen by pressing and holding the top of the pen for at least three seconds until the LED indicator flashes in green. 2. Enable Bluetooth pairing on your computer to discover and pair the pen. See “Connect to a Bluetoothenabled device” on page 26. The pen is discoverable as Lenovo Pen Pro. After pairing, press or double-press the top pen button to access more functions.
Chapter 3. Explore your computer Manage power Use the information in this section to achieve the best balance between performance and power efficiency. Check the battery status and temperature Check the battery status The battery status icon or is in the Windows notification area. You can click the icon to check the battery status, view the current power plan, change the power mode, and access battery settings quickly.
3. Change the settings as you prefer. Set the power plan For ENERGY STAR® compliant computers, the following power plan takes effect when your computers have been idle for a specified duration: Table 1. Default power plan (when plugged into ac power) • Turn off the display: After 10 minutes • Put the computer to sleep: After 10 minutes To reset the power plan to achieve the best balance between performance and power saving: 1. Right-click the battery status icon and select Power Options. 2.
• Secure Digital High-Capacity (SDHC) card Install the card 1. Locate the card slot. See “Right” on page 5. 2. Insert the card firmly into the card slot until it is secured in place. Ensure that the metal contacts are facing down and pointing toward the card slot. Remove the card Attention: Before removing a card, eject the card from the Windows operating system first. Otherwise, data on the card might get corrupted or lost. 1. Click the triangular icon in the Windows notification area to show hidden icons.
Note: When the new color profiles are installed successfully, a window will be displayed. Purchase options Lenovo has a number of hardware accessories and upgrades to help expand the capabilities of your computer. Options include memory modules, storage devices, network cards, port replicators or docking stations, batteries, power adapters, keyboards, mice, and more. To shop at Lenovo, go to https://www.lenovo.com/accessories.
Chapter 4. Secure your computer and information Lock the computer Lock your computer to a desk, table, or other fixtures through a compatible security cable lock. Note: The slot supports cable locks that conform to the Kensington MicroSaver® lock standards (using Tbar™ locking technology) or MiniSaver® lock standards (using Cleat™ locking technology). You are responsible for evaluating, selecting, and implementing the locking device and security feature.
Supervisor password The supervisor password protects the system information stored in UEFI BIOS. When entering the UEFI BIOS menu, enter the correct supervisor password in the window prompted. You also can press Enter to skip the password prompt. However, you cannot change most of the system configuration options in UEFI BIOS. If you have set both the supervisor password and power-on password, you can use the supervisor password to access your computer when you turn it on.
• A Trusted Computing Group (TCG) Opal-compliant storage drive and a TCG Opal management software program are installed in the computer, and the TCG Opal management software program is activated. • An eDrive storage drive is installed in the computer preinstalled with the Windows 10 operating system. Set, change, and remove a password Before you start, print these instructions. 1. Restart the computer. When the logo screen is displayed, press F1 to enter the UEFI BIOS menu. 2.
4. Type the current supervisor password in the Enter Current Password field. Then, leave the Enter New Password field blank, and press Enter twice. 5. In the Changes have been saved window, press Enter. 6. Press F10 to save changes and exit the UEFI BIOS menu. • If you have not set a supervisor password, contact a Lenovo authorized service provider to have the system management password removed. Use Power Loss Protection function For models shipped with an NVMe (Non-Volatile Memory express) M.
When you start the computer again, you can use your fingerprints to log in to the computer without entering your Windows password, power-on password, or hard disk password. To change the settings, go to the UEFI BIOS menu. Attention: If you always use your fingerprint to log in to the computer, you might forget your passwords. Write down your passwords, and keep them in a safe place.
34 P1 Gen 3 / X1 Extreme Gen 3 User Guide
Chapter 5. Configure advanced settings This chapter provides information about UEFI BIOS, RAID, recovery, operating system installation, and system management. UEFI BIOS This section introduces what is UEFI BIOS and the operations you can perform in UEFI BIOS. What is UEFI BIOS UEFI BIOS is the first program that the computer runs when the computer is turned on. UEFI BIOS initializes the hardware components and loads the operating system and other programs.
4. Press F10 to save the changes and exit. To change the startup sequence temporarily: 1. Restart the computer. When the logo screen is displayed, press F12. 2. Select the device that you want the computer to start from and press Enter. Set the system date and time 1. Restart the computer. When the logo screen is displayed, press F1. 2. Select Date/Time and set the system date and time as desired. 3. Press F10 to save changes and exit.
• RAID 1: mirrored disk array – Consists of two identical storage drives – Improved reading performance and 100% redundancy Enter the Intel RST configuration utility 1. Ensure that RAID is enabled in the UEFI BIOS menu: a. Restart the computer. When the logo screen is displayed, press F1 to enter the UEFI BIOS menu. b. Select Config ➙ Storage ➙ Controller Mode ➙ RST mode and then press Enter. c. Press F10 to save changes and exit. 2. Restart the computer.
1. Enter the Intel RST configuration utility. 2. Select the volume that you want to delete under RAID Volumes. Press Enter to open the RAID VOLUME INFO window. 3. Select Delete and press Enter to delete it from the RAID Volumes list. 4. When prompted, select Yes to confirm the deletion of the selected RAID volume. After you delete the RAID volume, the Intel (R) Rapid Storage Technology window is displayed. Member drives of the deleted volume are displayed under Non-RAID Physical Disks. 5.
Restore system files and settings to an earlier point 1. Go to Control Panel and view by Large icons or Small icons. 2. Click Recovery ➙ Open System Restore. Then, follow the on-screen instructions. Restore your files from a backup Note: If you use the File History tool to restore your files from a backup, ensure that you backed up your data earlier with the tool. 1. Go to Control Panel and view by Large icons or Small icons. 2. Click File History ➙ Restore personal files.
1. Ensure that your computer is connected to ac power. 2. Prepare a USB drive with at least 16 GB of storage capacity. The actual USB capacity required depends on the size of the recovery image. 3. Connect the prepared USB drive to the computer. 4. Type recovery in the search box. Then, click Create a recovery drive. 5. Click Yes in the User Account Control window to allow the Recovery Media Creator program to start. 6.
Attention: After you change the startup sequence, ensure that you select the correct device during a copy, a save, or a format operation. If you select the wrong device, the data on that device might be erased or overwritten. 7. Select Restart and ensure that OS Optimized Defaults is enabled. Then, press F10 to save the settings and exit. 8. Follow the on-screen instructions to install the device drivers and necessary programs. 9.
42 P1 Gen 3 / X1 Extreme Gen 3 User Guide
Chapter 6. CRU replacement What are CRUs Customer Replaceable Units (CRUs) are parts that can be upgraded or replaced by the customer. The computers contain the following types of CRUs: • Self-service CRUs: Refer to parts that can be installed or replaced easily by customer themselves or by trained service technicians at an additional cost. • Optional-service CRUs: Refer to parts that can be installed or replaced by customers with a greater skill level.
4. If prompted by User Account Control (UAC), click Yes. 5. Clear the Turn on fast startup check box, and then click Save changes. To disable the built-in battery: 1. Restart your computer. When the logo screen is displayed, immediately press F1 to enter the UEFI BIOS menu. 2. Select Config ➙ Power. The Power submenu is displayed. 3. Select Disable Built-in Battery and press Enter. 4. Select Yes in the Setup Confirmation window. The built-in battery is disabled and the computer turns off automatically.
5. Install the new base cover assembly in place 1 and tighten the screws to secure the base cover assembly 2 . 6. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer. Troubleshooting If the computer does not start up after you reinstall the base cover assembly, disconnect the ac power adapter and then reconnect it to the computer. Wireless WAN card (for selected models) The following information is only for the computer with user-installable modules.
5. Remove the wireless WAN card: a. Gently disconnect the wireless cable connectors with your fingers 1 . Then, remove the screw that secures the wireless WAN card 2 . b. Carefully remove the wireless WAN card out of the slot 3 . 6. Install a new wireless WAN card: a. Align the contact edge of the new wireless WAN card with the key in the slot. Then, carefully insert the card into the slot 1 . b. Install the screw to secure the wireless WAN card in place 2 .
Memory module Prerequisite Before you start, read Appendix A “Important safety information” on page 59 and print the following instructions. Attention: Do not touch the contact edge of the memory module. Otherwise, the memory module might get damaged. Replacement procedure Note: If you only install one memory module, install it in memory slot a . To replace a memory module, do the following: 1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 43. 2.
5. Open the latches on both sides of the memory slot at the same time 1 , and then remove the memory module 2 . Note: A Mylar film might cover the memory module. To access the memory module, open the film first. 6. Install the memory module: a. Place the notched end of the new memory module toward the contact edge side of the memory slot. Then, insert the new memory module into the memory slot at an angle of about 20 degrees 1 . b. Pivot the memory module downward until it snaps into place 2 .
M.2 solid-state drive Prerequisite Before you start, read Appendix A “Important safety information” on page 59 and print the following instructions. Attention: If you replace a M.2 solid-state drive, you might need to install a new operating system. For details on how to install a new operating system, see “Install Windows 10 and drivers” on page 40. The M.2 solid-state drive is sensitive. Inappropriate handling might cause damage and permanent loss of data. When handling the M.
4. Remove the base cover assembly. See “Base cover assembly” on page 44. 5. Remove the M.2 solid-state drive: a. Remove the screw that secures the M.2 solid-state drive 1 . Carefully remove the drive out of the slot 2. b. If your M.2 solid-state drive comes with a drive cover, slide the M.2 solid-state drive out of the drive cover 3 . 6. Install a new M.2 solid-state drive: a. If the new M.2 solid-state drive comes with a drive cover, insert the drive into the drive cover 1 . b.
8. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer. Coin-cell battery Prerequisite Before you start, read Appendix A “Important safety information” on page 59 and print the following instructions. DANGER If the coin-cell battery is incorrectly replaced, there is danger of an explosion. The coin-cell battery contains a small amount of harmful substance. To avoid possible injury: • Replace only with a battery of the type recommended by Lenovo.
6. Install the new coin-cell battery 1 , and then attach the connector 2 . 7. Reinstall the base cover assembly. 8. Turn over the computer. Connect the ac power adapter and all disconnected cables to the computer. 9. Reset the system date and time in the UEFI BIOS menu. See “Set the system date and time” on page 36.
Chapter 7. Help and support Frequently asked questions How do I access Control Panel? • Open the Start menu and click Windows System ➙ Control Panel. • Use Windows Search. How do I turn off my computer? Open the Start menu and click How do I partition my storage drive? https://support.lenovo.com/solutions/ht503851 Power. Then, click Shut down. 1. Press and hold the power button until the computer turns off. Then, restart the computer. 2.
Error messages If you see a message that is not included in the following table, record the error message first, then shut down the computer and call Lenovo for help. See “Lenovo Customer Support Center” on page 57. Message Solution 0190: Critical low-battery error The computer turned off because the battery power is low. Connect the ac power adapter to the computer and charge the batteries. 0191: System Security - Invalid remote change requested The system configuration change has failed.
Beep errors Lenovo SmartBeep technology enables you to decode beep errors with your smartphone when a black screen occurs with beeps from your computer. To decode the beep error with Lenovo SmartBeep technology: 1. Go to https://support.lenovo.com/smartbeep or scan the following QR Code. 2. Download the proper diagnostic app and install it on your smartphone. 3. Run the diagnostic app and place the smartphone near the computer. 4. Press Fn on your computer to emit the beep again.
Self-help resources Use the following self-help resources to learn more about the computer and troubleshoot problems. Resources How to access? Use Lenovo Vantage to: • Configure device settings. • Download and install UEFI BIOS, drivers, and firmware updates. • Secure your computer from outside threats. • Open the Start menu and click Lenovo Vantage. • Use Windows Search. • Diagnose hardware problems. • Check the computer warranty status. • Access User Guide and helpful articles.
Call Lenovo If you have tried to correct the problem yourself and still need help, you can call Lenovo Customer Support Center. Before you contact Lenovo Prepare the following before you contact Lenovo: 1. Record the problem symptoms and details: • What is the problem? Is it continuous or intermittent? • Any error message or error code? • What operating system are you using? Which version? • Which software applications were running at the time of the problem? • Can the problem be reproduced? If so, how? 2.
Services available during the warranty period • Problem determination - Trained personnel are available to assist you with determining if you have a hardware problem and deciding what action is necessary to fix the problem. • Lenovo hardware repair - If the problem is determined to be caused by Lenovo hardware under warranty, trained service personnel are available to provide the applicable level of service.
Appendix A. Important safety information Safety notices This information can help you safely use your computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the Limited Warranty. For more information, see "Warranty Information" in the Safety and Warranty Guide that comes with your computer. Customer safety is important. Our products are developed to be safe and effective.
Protect yourself from the heat generated by the ac power adapter. When the ac power adapter is connected to an electrical outlet and your computer, it generates heat. Extended contact with your body, even through clothing, may cause a skin burn. • Do not place the ac power adapter in contact with any part of your body while it is in use. • Never use it to warm your body. • Do not wrap the cords around the ac power adapter while in use. Prevent your computer from getting wet.
Handle your computer gently. Do not drop, bump, scratch, twist, hit, vibrate, push, or place heavy objects on your computer, display, or external devices. Carry your computer carefully. • Use a quality carrying case that provides adequate cushioning and protection. • Do not pack your computer in a tightly packed suitcase or bag. • Before putting your computer in a carrying case, make sure that it is off, in sleep mode, or in hibernation mode.
• Power cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are cracked, broken, or damaged. • Signs of overheating, smoke, sparks, or fire. • Damage to a battery (such as cracks, dents, or creases), discharge from a battery, or a buildup of foreign substances on the battery. • A cracking, hissing, or popping sound, or strong odor that comes from the product.
When replacing CRUs, be cautious of sharp edges or corners that might cause injury. If you suffer an injury, seek medical care immediately. Power cords and power adapters DANGER Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H03VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly. Never wrap a power cord around a power adapter or other object.
Plugs and outlets DANGER If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.
General battery notice DANGER Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts. A battery other than the one specified by Lenovo, or a disassembled or modified battery is not covered by the warranty. Battery abuse or mishandling can cause overheat, liquid leakage, or an explosion. To avoid possible injury: • Do not open, dissemble, or service any battery. • Do not crush or puncture the battery.
The Lenovo-authorized repair facilities or technicians recycle Lenovo batteries according to local laws and regulations. When replacing the lithium coin-cell battery, use only the same type or equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Swallowing the lithium coin-cell battery will cause chocking or severe internal burns in just two hours and might even result in death.
Heat and product ventilation DANGER Computers, ac power adapters, and many accessories can generate heat when turned on and when batteries are charging. Notebook computers can generate a significant amount of heat due to their compact size. Always follow these basic precautions: • When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot.
Electrical current safety information DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not use your computer during a lightning storm. • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect properly wired outlets to any equipment that will be attached to this product.
Liquid crystal display (LCD) notice CAUTION: The liquid crystal display (LCD) is made of glass, and rough handling or dropping the computer can cause the LCD to break. If the LCD breaks and the internal fluid gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes; if any symptoms are present after washing, get medical care.
Glass parts notice CAUTION: Some parts of your product may be made of glass. This glass could break if the product is dropped on a hard surface or receives a substantial impact. If glass breaks, do not touch or attempt to remove it. Stop using your product until the glass is replaced by trained service personnel. Static electricity prevention Static electricity, although harmless to you, can seriously damage computer components and options. Improper handling of static-sensitive parts can damage the part.
Basic maintenance tips Here are some basic points about keeping your computer functioning properly: • If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine. • Store packing materials safely out of the reach of children to prevent the risk of suffocation from plastic bags. • Keep your computer away from magnets, activated cellular phones, electrical appliances, or speakers (more than 13 cm or 5 inches).
72 P1 Gen 3 / X1 Extreme Gen 3 User Guide
Appendix B. Accessibility and ergonomic information This chapter provides information about accessibility and ergonomics. Accessibility information Lenovo is committed to providing users who have hearing, vision, and mobility limitations with greater access to information and technology. This section provides information about the ways these users can get the most out of their computer experience. You also can get the most up-to-date accessibility information from the following Web site: https://www.
keyboard with all the standard keys. You can select keys using the mouse or another pointing device, or you can tap to select the keys if your computer supports multi-touch screen. • High Contrast High Contrast is a feature that heightens the color contrast of some text and images on your screen. As a result, those items are more distinct and easier to identify. • Personalized keyboard Adjust keyboard settings to make your keyboard easier to use.
– Change the size of all the items on your screen. 1. Right-click a blank area on the desktop and then click Display settings ➙ Display. 2. Change the item size by following the on-screen instructions. For some applications, your configuration might not take effect until you sign out and then sign in again. – Change the size of the items on a Web page. Press and hold Ctrl, and then press the plus-sign key (+) to enlarge or the minus-sign key (–) to reduce the text size.
Display: Position the display to maintain a comfortable viewing distance of 510 mm to 760 mm (20 inches to 30 inches). Avoid glare or reflections on the display from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness to levels that enable you to see the screen clearly. Press the brightness control keys to adjust display brightness. Head position: Keep your head and neck in a comfortable and neutral (vertical, or upright) position.
Appendix C. Supplemental information about the Linux operating system In limited countries or regions, Lenovo offers customers an option to order computers with the preinstalled Linux® operating system. If the Linux operating system is available on your computer, read the following information before you use the computer. Ignore any information related to Windows-based programs, utilities, and Lenovo preinstalled applications in this documentation.
78 P1 Gen 3 / X1 Extreme Gen 3 User Guide
Appendix D. Compliance and TCO Certified information This chapter provides regulatory, environmental, RoHS, and ENERGY STAR information about Lenovo products. Radio frequency compliance statements Computer models equipped with wireless communications comply with the radio frequency and safety standards of any country or region in which it has been approved for wireless use.
Locate the UltraConnect wireless antennas Your computer has an UltraConnect™ wireless antenna system. You can enable wireless communication wherever you are.
This equipment is not protected against harmful interference and may not cause interference with duly authorized systems. Mexico Advertencia: En Mexico la operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Singapore Korea 무선설비 전파 혼신 (사용주파수 2400∼2483.
The WEEE marking on Lenovo products applies to countries with WEEE and e-waste regulations (for example, the European WEEE Directive, India E-Waste Management Rules). Appliances are labeled in accordance with local regulations concerning waste electrical and electronic equipment (WEEE). These regulations determine the framework for the return and recycling of used appliances as applicable within each geography.
lithium battery, insulate it with vinyl tape, contact your place of purchase or an industrial-waste-disposal operator, and follow their instructions. Disposal of a lithium battery must comply with local ordinances and regulations. Dispose of a disused battery from Lenovo notebook computers Your Lenovo notebook computer has a lithium ion battery or a nickel metal hydride battery.
Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted municipal waste, but use the collection framework available to customers for the return, recycling, and treatment of batteries and accumulators. Customer participation is important to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances.
Battery recycling information for the United States and Canada Restriction of Hazardous Substances (RoHS) Directive of countries and regions The latest environmental information about Lenovo products is available at: https://www.lenovo.
86 P1 Gen 3 / X1 Extreme Gen 3 User Guide
Taiwan RoHS Electromagnetic emission notices Federal Communications Commission (FCC) Supplier’s Declaration of Conformity The following information refers to ThinkPad P1 Gen 3 and ThinkPad X1 Extreme Gen 3. Appendix D.
Product name Machine types ThinkPad P1 Gen 3 20TH and 20TJ ThinkPad X1 Extreme Gen 3 20TK and 20TL This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Compliance with the EMC Directive This product is in conformity with the protection requirements of EU Council Directive 2014/30/EU on the approximation of the laws of the Member States relating to electromagnetic compatibility. This product has been tested and found to comply with the limits for Class B equipment according to European Standards harmonized in the Directives in compliance.
Other compliance and TCO Certified information of countries and regions This section provides other compliance information about Lenovo products.
Lenovo product service information for Taiwan Taiwan precautionary vision statement 警語：使用過度恐傷害視力 注意事項： • 使用30分鐘請休息10分鐘。 • 未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小時。 Supplemental information for the Eurasian Union Назначение персональный компьютер для личного и служебного использования, для передачи данных, с поддержкой различных профилей подключения (Wi-Fi, Bluetooth и пр.).
ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer products with the ENERGY STAR certified designation. Lenovo computers, if carry an ENERGY STAR mark, have been designed and tested to conform to the ENERGY STAR program requirements for computers as prescribed by the U.S. Environmental Protection Agency.
Appendix E. Notices and trademarks Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary.
