Hardware Maintenance Manual ThinkServer TD200x Machine Types: 3719, 3821, 3822, and 3823
ThinkServer TD200x Types 3719, 3821, 3822, and 3823 Hardware Maintenance Manual
Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 279 and the Warranty and Support Information document on the Lenovo® ThinkServer Documentation DVD. First Edition (July 2009) © Copyright Lenovo 2009. Portions © Copyright International Business Machines Corporation 2009.
Contents Chapter 1. About this manual . . Important Safety Information . . . Important information about replacing Turkish statement of compliance . . . . . . . . . . . . . . . . . . . . RoHS compliant FRUs . . . . . . . . . Chapter 2. Safety information . . . . . . Guidelines for trained service technicians . . Inspecting for unsafe conditions . . . . . Guidelines for servicing electrical equipment Safety statements . . . . . . . . . . . Chapter 3. General information Features and technologies . .
Viewing the test log . . . . . . . . . . . . . Diagnostic messages . . . . . . . . . . . . Recovering from a Lenovo ThinkServer Server Firmware Solving power problems . . . . . . . . . . . . Solving Ethernet controller problems . . . . . . . Solving undetermined problems . . . . . . . . . Problem determination tips . . . . . . . . . . . . . . . . . . . . . . . update failure . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 . . . 91 . . . 122 . . . 123 . . . 123 . . . 124 . . . 125 Chapter 6.
| | Installing the front adapter-retention bracket . . . Removing the rear adapter retention bracket . . Installing the rear adapter retention bracket . . . Removing an adapter . . . . . . . . . . . Installing an adapter . . . . . . . . . . . Removing the DVD drive . . . . . . . . . . Installing a DVD (optical) drive. . . . . . . . Removing an optional tape drive . . . . . . . Installing a USB or SATA tape drive . . . . . . Removing the USB cable and EasyLED panel . .
EasyStartup overview . . . . . . . . . . . . . . . Installing your operating system without using EasyStartup . Enabling the Broadcom Gigabit Ethernet Utility program . . . Configuring the Gigabit Ethernet controller . . . . . . . . Updating the firmware . . . . . . . . . . . . . . . . Using the EasyUpdate Firmware Updater tool . . . . . . Starting the backup server firmware . . . . . . . . . . . Using the Integrated Management Module . . . . . . . .
Chapter 1. About this manual This Hardware Maintenance Manual contains information to help you solve problems that might occur in your server. It describes the diagnostic tools that come with the server, error codes and suggested actions, and instructions for replacing failing components. Replaceable components are of three types: | | | | | | | | v Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market and sold in the European Union after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
Turkish statement of compliance The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (EEE). Türkiye EEE Yönetmeliğine Uygunluk Beyanı Bu Lenovo ürünü, T.C. Çevre ve Orman Bakanlığı'nın “Elektrik ve Elektronik Eşyalarda Bazı Zararlı Maddelerin Kullanımının Sınırlandırılmasına Dair Yönetmelik (EEE)” direktiflerine uygundur. EEE Yönetmeliğine Uygundur. Chapter 1.
4 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Chapter 2. Safety information Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Lees voordat u dit product installeert eerst de veiligheidsvoorschriften. Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Guidelines for trained service technicians This section contains information for trained service technicians. Inspecting for unsafe conditions Use the information in this section to help you identify potential unsafe conditions in a Lenovo product that you are working on. Each Lenovo product, as it was designed and manufactured, has required safety items to protect users and service technicians from injury. The information in this section addresses only those items.
v Do not touch the reflective surface of a dental mirror to a live electrical circuit. The surface is conductive and can cause personal injury or equipment damage if it touches a live electrical circuit. v Some rubber floor mats contain small conductive fibers to decrease electrostatic discharge. Do not use this type of mat to protect yourself from electrical shock. v Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
Safety statements Important: Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document. For example, if a caution statement is labeled "Statement 1," translations for that caution statement are in the Safety Information document under "Statement 1.
Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product. v When possible, use one hand only to connect or disconnect signal cables.
Statement 2: CAUTION: When replacing the lithium battery, use only a type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. v Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
Statement 4: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. Statement 26: CAUTION: Do not place any object on top of rack-mounted devices.
14 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. Features and technologies The TD200x server offers the following features and technologies: v UEFI-compliant server firmware The server firmware offers several features, including Unified Extensible Firmware Interface (UEFI) 2.1 compliance, enhanced RAS capabilities, and BIOS compatibility support.
– – – – – System configuration Network interfaces and settings Installed hardware EasyLED diagnostics status Service processor status and configuration – Vital product data, firmware, and UEFI (formerly BIOS) configuration – Hard disk drive health – RAID controller configuration – Event logs for service processors The diagnostic programs create a merged log that includes events from all collected logs. The information is collected into a file that you can send to Lenovo service and support.
The server has one slot for a PCI-32 adapter. v PCI Express x8 adapter capabilities The server has five slots for PCI Express x8 adapters. Three of these slots accept x8 adapters, but the adapters will operate as x4 adapters. v PCI Express x16 adapter capabilities The server has one slot for PCI Express x16 adapter, which will operate as an x8 adapter. v Redundant cooling and power capabilities The server supports up to two 920-watt hot-swap power supplies.
Table 1.
EasyStartup The ThinkServer EasyStartup program simplifies the process of your RAID controller and installing supported Microsoft® Windows® and Linux operating systems and device drivers on your server. The EasyStartup program is provided with your server on DVD. The DVD is self starting (bootable). The user guide for the EasyStartup program is on the DVD and can be accessed directly from the program interface. For additional information, see “Using the ThinkServer EasyStartup DVD” on page 263.
20 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Chapter 4. General Checkout You can solve many problems without outside assistance by following the troubleshooting procedures in this Hardware Maintenance Manual and on the Lenovo Web site. This document describes the diagnostic tests that you can perform, troubleshooting procedures, and explanations of error messages and error codes. The documentation that comes with your operating system and software also contains troubleshooting information.
v If the server is halted and a POST error code is displayed, see “POST error codes” on page 30. If the server is halted and no error message is displayed, see “Troubleshooting tables” on page 64 and “Solving undetermined problems” on page 124. v For information about power-supply problems, see “Solving power problems” on page 123 and “Power-supply LEDs” on page 88.
Determine whether any of the following items were added, removed, replaced, or updated before the problem occurred: v Lenovo ThinkServer Server Firmware (server firmware) v Device drivers v Firmware v Hardware components v Software If possible, return the server to the condition it was in before the problem occurred. 2. Collect data. Thorough data collection is necessary for diagnosing hardware and software problems. a. Document error codes and system-board LEDs.
Important: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. 1) Determine the existing code levels. In DSA, click Firmware/VPD to view system firmware levels, or click Software to view operating-system levels. 2) Download and install updates of code that is not at the latest level.
Note: Changes are made periodically to the Lenovo Web site. The actual procedure might vary slightly from what is described in this document. a) Go to: http://www.lenovo.com/support. b) Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. c) Select Servers and Storage from the Brand list. d) From Family list, select ThinkServer TD200x, and click Continue.
26 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Chapter 5. Diagnostics This chapter describes the diagnostic tools that are available to help you solve problems that might occur in the server. If you cannot diagnose and correct a problem by using the information in this chapter, see Appendix A, “Getting help and technical assistance,” on page 275 for more information.
Some IMM sensors cause assertion events to be logged when their setpoints are reached. When a setpoint condition no longer exists, a corresponding deassertion event is logged. However, not all events are assertion-type events. v Integrated management module (IMM) event log: This log contains a filtered subset of all IMM, POST, and system management interrupt (SMI) events.
Table 2. Methods for viewing event logs Condition Action The server is not hung and is connected to a Use any of the following methods: network. v Run Portable or Installable DSA to view the event logs or create an output file that you can send to Lenovo service and support. v Type the IP address of the IMM and go to the Event Log page. v Use IPMItool to view the system-event log. The server is not hung and is not connected to a network. Use IPMItool locally to view the system-event log.
POST error codes When you turn on the server, it performs a series of tests to check the operation of the server components and some optional devices in the server. This series of tests is called the power-on self-test, or POST. If a power-on password is set, you must type the password and press Enter, when you are prompted, for POST to run. If POST is completed without detecting any problems, the server startup is completed. If POST detects a problem, an error message is sent to the POST event log.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
System-event log The system-event log contains messages of three types: Information Information messages do not require action; they record significant system-level events, such as when the server is started. Warning Warning messages do not require immediate action; they indicate possible problems, such as when the recommended maximum ambient temperature is exceeded. Error Error messages might require action; they indicate system errors, such as when a fan is not detected.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Hostname set to %1 by user %2.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Watchdog %1 Failed to Capture Screen.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms. If you cannot find a problem in these tables, see “Running the diagnostic programs” on page 90 for information about testing the server. If you have just added new software or a new optional device and the server is not working, complete the following steps before you use the troubleshooting tables: 1.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Keyboard, mouse, or pointing-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Memory problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Microprocessor problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Monitor problems Some Lenovo monitors have their own self-tests. If you suspect a problem with your monitor, see the documentation that comes with the monitor for instructions for testing and adjusting the monitor. v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Optional-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Power problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Software problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
| EasyLED diagnostics EasyLED diagnostics is a system of LEDs on various external and internal components of the server. When an error occurs, LEDs are lit throughout the server. By viewing the LEDs in a particular order, you can often identify the source of the error. When LEDs are lit to indicate an error, they remain lit when the server is turned off, provided that the server is still connected to power and the power supply is operating correctly.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
1 2 3 4 5 6 7 Server processor bus Microprocessor VRM Microprocessor/memory configuration Memory NMI Hard disk drive/RAID 8 9 10 11 12 13 14 Power supply Fan PCI bus System board Temperature System-event log USB ports The following table lists the EasyLED diagnostics LEDs, the problems that they indicate, and actions to solve the problems. v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
3. Remove the server cover and look inside the server for lit LEDs. Certain components inside the server have LEDs that are lit to indicate the location of a problem. The following illustration shows the LEDs on the system board.
The system board is equipped with a PCI extender card that provides either one or two additional expansion slots. The following illustration shows the LEDs on the PCI Express extender card, if one is installed. The following illustration shows the LEDs on the PCI-X extender card, if one is installed. The following table describes the LEDs on the system board and extender card and suggested actions to correct the detected problems.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Power-supply LEDs The following illustration shows the power-supply LEDs on the rear of the server. 1 2 3 ac power LED dc power LED Power error LED The following table describes the problems that are indicated by various combinations of the power-supply LEDs and the system power LED on the operator information panel and suggested actions to correct the detected problems.
Table 3. Power-supply LEDs Power-supply LEDs AC DC Off Off Error Off Description Action Notes No ac power to the server or a problem with the ac power source 1. Check the ac power to the server. This is a normal condition when no ac power is present. 2. Make sure that the power cord is connected to a functioning power source. 3. Turn the server off and then turn the server back on. 4. If the problem remains, replace the power supply.
Diagnostic programs, messages, and error codes The diagnostic programs are the primary method of testing the major components of the server. As you run the diagnostic programs, text messages and error codes are displayed on the screen and are saved in the test log. A diagnostic text message or error code indicates that a problem has been detected; to determine what action you should take as a result of a message or error code, see the table in “Diagnostic messages” on page 91.
User Aborted: You stopped the test before it was completed. Not Applicable: You attempted to test a device that is not present in the server. Aborted: The test could not proceed because of the server configuration. Warning: The test could not be run.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 4. DSA messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Recovering from a Lenovo ThinkServer Server Firmware update failure If power to the server is interrupted while you are updating the Lenovo ThinkServer Server Firmware, the server might not restart correctly or might not display video. If this happens, complete the following steps to recover: 1. Read the safety information that begins on page 5. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3.
10. 11. 12. 13. 14. Disconnect all power cords and external cables. Remove the side cover (see “Removing the left-side cover” on page 157). Remove any adapters that impede access to jumper JP6. Move jumper JP6 to back to pins 1 and 2 for normal operation. Replace any adapters that you removed; then, install the side cover (see “Installing the left-side cover” on page 158). 15. Lock the side cover if you unlocked it during removal. 16.
v Check the Ethernet controller LEDs on the rear panel of the server. These LEDs indicate whether there is a problem with the connector, cable, or hub. – The Ethernet link status LED is lit when the Ethernet controller receives a link pulse from the hub. If the LED is off, there might be a defective connector or cable or a problem with the hub. – The Ethernet transmit/receive activity LED is lit when the Ethernet controller sends or receives data over the Ethernet network.
4. Turn on the server. If the problem remains, suspect the following components in the following order: a. Power supply b. Power-supply cage c. Memory d. Microprocessor e. System board If the problem is solved when you remove an adapter from the server but the problem recurs when you reinstall the same adapter, suspect the adapter; if the problem recurs when you replace the adapter with a different one, suspect the system board or extender card.
See Appendix A, “Getting help and technical assistance,” on page 275 for information about calling Lenovo for service.
Chapter 6. Locating Server Controls and connectors This section describes the controls and light-emitting diodes (LEDs) and how to turn the server on and off. Front view The following illustration shows the controls and LEDs on the front of the server. Note: The front bezel door is not shown so that the drive bays are visible.
1 2 3 4 5 System power-on LED Hard disk drive activity LED System-locator LED System-information LED System-error LED v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 8, “Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823,” on page 237 to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Rear view The following illustration shows the connectors and LEDs on the rear of the server. 1 2 3 4 5 6 USB 1 USB 2 USB 3 USB 4 Ethernet 10/100/1000 Power-cord connector 7 8 9 10 11 12 Power-error LED dc-power LED ac-power LED Video connector Serial 1 (COM 1) Systems-management connector USB 1-4 connectors: Connect a USB device, such as USB mouse or keyboard, to any of these connectors. Ethernet 10/100/1000 connector: Use these connectors to connect the server to a network.
ac-power LED: Each hot-swap power supply has an ac-power LED and a dc-power LED. When the ac-power LED is lit, it indicates that sufficient power is coming into the power supply through the power cord. During typical operation, both the ac and dc-power LEDs are lit. For any other combination of LEDs, see “Power-supply LEDs” on page 139. Video connector: Connect a monitor to this connector. Serial 1 connector (COMM 1): Connect a 9-pin serial device to this connector.
1 Microprocessor 2 21 Wake on LAN 2 System power 22 Battery 3 ADV power 23 PCI Express x8 slot 7 4 Optical power 24 PCI - 32 slot 6 5 Front panel 25 PCI Express x8 slot 5 6 EasyLED panel 26 PCI Express x8 slot 4 7 USB tape 27 PCI Express x8 slot 3 8 DIMM 8 28 PCI Express x8 slot 2 9 DIMM 1 29 PCI Express x8 slot 1 10 SATA backplane 2 power 30 Virtual media key connector 11 Front USB 31 VRM connector (Microprocessor 2) 1
System-board external connectors The following illustration shows the external input/output connectors and the NMI button on the system board. 1 2 3 4 5 6 Video port Serial port 10/100m RJ45 LAN connector NMI button USB ports GbE RJ45 LAN connectors System-board switches and jumpers The following illustration shows the SW6 switch and the jumpers on the system board. See the tables below the illustration for information about the switch settings. Chapter 6.
Table 6. System-board jumpers Jumper number Jumper name 1 JP6 UEFI boot v Pins 1 and 2: Normal operation (default). recovery v Pins 2 and 3: Enable the UEFI recovery mode. 2 JP1 CMOS clear 3 SW6 Jumper setting v Pins 1 and 2: Normal operation (default). v Pins 2 and 3: Clears CMOS. switch block Note: If no jumper is present, the server responds as if the pins are set to 1 and 2. Table 7.
System-board LEDs The following illustration shows the LEDs on the system board.
Express extender card 1 , if one is installed. The following illustration shows the LEDs ( 1 and 2 ) on the PCI-X extender card, if one is installed. The following table describes the LEDs on the system board and extender card and suggested actions to correct the detected problems. v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Lit EasyLED diagnostics LED with the system-error or information LED also lit Description CPU 2 error LED Microprocessor 2 has failed, is missing, or has been incorrectly installed.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Lit EasyLED diagnostics LED with the system-error or information LED also lit Description Action PCI slot 1 to PCI slot 8 error LEDs 1. Check the system-event log for information about the error.
Power-supply LEDs The following illustration shows the power-supply LEDs on the rear of the server. For more information about solving power-supply problems, see “Solving power problems” on page 123. 1 2 3 ac power LED dc power LED Power error LED The following table describes the problems that are indicated by various combinations of the power-supply LEDs and the power-on LED on the operator information panel and suggested actions to correct the detected problems. Chapter 6.
Table 8. Power-supply LEDs Power-supply LEDs ac dc Off Off Error Off Description Action Notes No ac power to the server or a problem with the ac power source 1. Check the ac power to the server. This is a normal condition when no ac power is present. 2. Make sure that the power cord is connected to a functioning power source. 3. Turn the server off and then turn the server back on. 4. If the problem remains, replace the power supply.
System-board internal connectors The following illustration shows the internal connectors on the system board.
142 19 Fans 1, 2, and 3 39 DIMM 9 20 SATA 1 40 DIMM 16 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
The system board is equipped with a PCI extender card that provides either one or two additional expansion slots. The following illustration shows one additional PCI Express expansion slot that is available on the PCI Express extender card, if equipped. 1 PCI Express x8 slot 7 The following illustration shows two additional PCI-X expansion slots that are available on the PCI-X extender card, if equipped. 1 2 PCI-X 1 slot 7 PCI-X 2 slot 8 Chapter 6.
System-board switches and jumpers The following illustration shows the switches and jumpers on the system board. See Table 9 and Table 10 for information about the switch and jumper settings. Table 9. System-board jumpers Jumper number Jumper name JP1 CMOS clear v Pins 1 and 2: Normal operation (default). Jumper setting v Pins 2 and 3: Clears CMOS memory. JP6 UEFI boot recovery v Pins 1 and 2: Normal operation (default). v Pins 2 and 3: Enable the UEFI recovery mode.
System-board LEDs The following illustration shows the LEDs on the system board.
The system board is equipped with a PCI extender card that provides either one or two additional expansion slots. The following illustration shows the LEDs on the PCI Express extender card 1 , if one is installed. The following illustration shows the LEDs ( 1 and 2 ) on the PCI-X extender card, if one is installed. System-board external connectors The following illustration shows the external input/output connectors on the system board.
2.5-inch hard disk drive backplane connectors The following illustration shows the connectors on the 2.5-inch hard disk drive backplane.
Turning off the server When you turn off the server and leave it connected to ac power, the server can respond to requests from the IMM, such as a remote request to turn on the server. While the server remains connected to ac power, one or more fans might continue to run. To remove all power from the server, you must disconnect it from the power source. Important: To view the error LEDs on the system board, leave the server connected to a power source.
Chapter 7. Installing optional devices and replacing customer replaceable units Important: Before you install optional hardware, make sure that the server is working correctly. Start the server, and make sure that the operating system starts, if an operating system is installed. If the server is not working correctly, see the Chapter 5, “Diagnostics,” on page 27 for diagnostic information. This chapter provides detailed instructions for installing optional hardware devices in the server.
Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the server, open or close a latch, and so on. Orange on a component or an orange label on or near a component indicates that the component can be hot-swapped, which means that if the server and operating system support hot-swap capability, you can remove or install the component while the server is running. (Orange can also indicate touch points on hot-swap components.
Closing the bezel 1 Pull point To close the bezel, do the following: 1. Rotate the left side of the bezel toward the server to the closed position. 2. Lock the left-side cover, using the key that comes with the server. Chapter 7.
Removing the bezel 1 2 3 Bezel Hinge assembly Retention tabs To remove the bezel, do the following: 1. Read the safety information that begins on page 5. 2. Unlock the left-side side cover. Note: You must unlock the side cover to remove the bezel. 3. Open the bezel (see “Opening the bezel” on page 150).
4. Press the retention tabs 1 on the hinge assembly toward each other and pull the hinge assembly out of the chassis. Note: The bezel will also disengage from the chassis hinges if you rotate the bezel beyond 180° or if excessive pressure is applied to the bezel. Do not be alarmed because this is how the bezel was designed. The bezel is designed with breakaway hinges so that you can easily reattach it to the chassis. 5.
Installing the bezel 1 2 3 To 1. 2. 3. Bezel Hinge assembly Retention tabs install the bezel, do the following: Align the hinge assemblies with the hinge holes on the chassis. Push the hinges into the holes on the chassis until they snap into place. If however, the bezel was removed by detaching the sliding hinge mount from the hinge assembly (using the breakaway method as the bezel was designed to do), complete the following steps to reattach the bezel: a.
b. Align the sliding hinge mount 1 with the hinge pin 2 on the hinge assembly 3 on the chassis. c. Press the sliding hinge mount against the hinge pin until the sliding hinge mount snaps onto the hinge pin. 4. Close the bezel (see “Closing the bezel” on page 151). 5. Lock the left-side cover. Opening the bezel media door To open or remove the media door, do the following: 1. Read the safety information that begins on page 5. 2. Unlock the side cover.
1 2 Bezel media door Media door lock Note: To remove the media door from the bezel, push upward on the media door hinge to remove it from the bezel. 5. When the media door is unlocked, the icon on the side of the bezel 1 will be in the unlocked position. Closing the bezel media door To close the media door, do the following: 1. Swing the bezel media door closed and push it into the bezel to close it. 2.
1 2 Bezel media door Media door lock 3. Close the bezel (see “Closing the bezel” on page 151). Removing the left-side cover Important: Before you install optional hardware, make sure that the server is working correctly. If an operating system is installed, start the server, and make sure that the operating system starts.
2. If you are planning to view the error LEDs that are on the system board and components, leave the server connected to power and go directly to step 5. 3. Turn off the server and all attached devices. 4. Disconnect all external cables and power cords. 5. Using the supplied key, unlock the left-side cover. 6. Pull the cover-release latch down and rotate the top edge of the cover away from the server. Attention: For proper cooling and airflow, replace the cover before you turn on the server.
3. Press the release latch on the power supplies and filler panels and pull them out of the power-supply cage. 1 2 Release latch Hot-swap power supply 4. Unlock and remove the left-side cover. 5. Pull up on the power-supply cage handle to unlock the cage; then, rotate the cage out until it stops. The tab on the rear power-supply latch bracket will click into place when the cage is completely out of the way. 1 2 Power-supply cage Power-supply cage handle 6.
Closing the power-supply cage To return the power-supply cage to its closed position, do the following: 1. Rotate the power-supply cage back slightly; then, push the release tab on the rear power-supply support bracket out of the way. 1 2 Power supply support bracket Power supply release tab Attention: Be sure to move the cables out of the way of the power supply cage before you start to move the cage back into the server.
2. Carefully rotate the power-supply cage into the server chassis. The locating tabs on the power-supply cage must fit over the corresponding tabs on the front latch bracket. 1 2 3 4 5 6 Power-supply cage handle Power-supply cage Power-supply cage front latch bracket Locating tabs Notch Locating tabs 3. Rotate the power-supply cage handle down until the handle tip engages the notch in the front latch bracket; then, lower the handle until it locks in place (power supply cage closed 1 ).
4. Install and lock the left-side cover (see “Installing the left-side cover” on page 158). 5. Install the hot-swap power supplies. 6. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Turning the stabilizing feet To rotate the front feet, do the following: 1. Carefully position the server on a flat surface. The feet ( 1 ) should hang over the edge of the flat surface to ease removal. 2.
3. Reinstall the feet 1 in the opposite location. The tab on the feet should extend beyond the edge of the server. Internal cable routing and connectors You can install either an USB or a SATA tape drive in the server. The following illustration shows the internal cable routing and connectors for both the USB tape drive and the SATA tape drive. It also shows the internal power cable for the optical drives.
The following illustration shows the internal SAS/SATA cable routing and connectors from the ServeRAID BR10i controller to eight 2.5-inch hard disk drives. The left port on the ServeRAID BR10i controller is connected to the backplane for drives 4-7 and the right port on the adapter is connected to the backplane for drives 0-3.
The following illustration shows the internal SAS/SATA cable routing and connectors from the ServeRAID BR10i controller to 16 2.5-inch hard disk drives. The following illustration shows the cable connectors on the ServeRAID-BR10i controller. 1 2 3 ServeRAID-BR10i controller Cable connector for drives 0 - 3 Cable connector for drives 4 - 7 Chapter 7.
The following illustration shows the internal SAS/SATA cable routing and connectors from the ServeRAID MR10i or ServeRAID MR10is controllers to eight 2.5-inch hard disk drives. The right port on the ServeRAID MR10i or ServeRAID MR10is controller is connected to the backplane for drives 4-7 and the left port on the controller is connected to the backplane for drives 0-3.
The following illustration shows the internal SAS power and signal cable routing from the hard disk drives to the connectors on the system board. 1 2 SAS power cable connector B SAS power cable connector A The following illustration shows the internal SATA and power cable routing and the connectors from the DVD drive to the system board. Chapter 7.
The following illustration shows the internal cable routing and connectors from the operator information panel to the system board. 1 2 Operator information panel cable connector Operator information panel cable The following illustration shows the internal cable routing and connectors from the EasyLED diagnostics panel to the system board.
Removing the air baffle To remove the air baffle, do the following: 1. Read the safety information that begins on page 5. 2. 3. 4. 5. 6. Turn off the server and all attached devices. Disconnect all external cables and power cords. Remove the left-side cover. Remove the power supplies from the power supply cage. Unlatch the power supply cage and rotate it out of the server until it locks. 7.
Installing the air baffle To install the air baffle, do the following: 1. With the rear (hinged) part of the air baffle 3 lifted up, align the positioning pins on the ends of the air baffle with the locating holes in the server chassis and fan-cage assembly. 2. Slide the air baffle down into the server 1 until the positioning pins fit into the locating holes; then, press down on the air baffle until the pinch tab clicks into place. 3.
Removing the fan-cage assembly 1 2 Fan cage assembly Fan cage assembly release buttons To remove the fan-cage assembly, do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Turn the server on its side so that it is lying flat, with the side cover facing up. 4. Unlock and remove the left-side cover (see “Removing the left-side cover” on page 157). 5.
Installing the fan-cage assembly 1 2 Fan cage assembly Fan cage assembly release buttons To install the fan-cage assembly, do the following: 1. Align the guides on the fan cage with release latches on each side. 2. Push the fan-cage assembly into the server until it clicks into place. 3. If you removed any full-length PCI adapters, install them (see “Installing an adapter” on page 184). 4. Install the air baffle (see “Installing the air baffle” on page 170). 5.
6. Locate the battery on the system board (see “System-board internal connectors” on page 131). 7. Remove the battery: a. Use one finger to push the battery horizontally out of its socket, pushing it away from the socket. b. Lift and remove the battery from the socket. 8. Dispose of the battery as required by local ordinances or regulations.
To install the replacement battery, do the following: 1. Follow any special handling and installation instructions that come with the replacement battery. 2. Insert the replacement battery 1 : a. Hold the battery in a vertical orientation so that the smaller side is facing the socket. b. Place the battery into its socket, and press the battery towards the socket until it clicks into place. Make sure that the battery clip holds the battery securely. 3.
To remove a hot-swap power supply, do the following: 1. Read the safety information Chapter 2, “Safety information,” on page 5. Attention: Static electricity that is released to internal server components when the server is powered on might cause the server to halt, which might result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when you work inside the server with the power on. 2.
CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. 1 2 Hot-swap power supply Release latch To install a hot-swap power supply, do the following: 1.
5. Connect one end of the power cord for the new power supply into the connector on the back of the power supply; then, connect the other end of the power cord to a properly grounded electrical outlet. Note: If the server has been turned off, you must wait approximately 3 minutes after you connect the server power cord to an electrical outlet before the power-control button becomes active. 6.
1 2 Release latch Hot-swap power supply 5. Remove the power supply filler from the second power supply bay. 6. Slide the new power supply partially into the empty power supply bay. Pinch the orange release latch and push the power supply the rest of the way into the bay until it is seated. 7. Install the left-side cover. 8. Connect one end of the new power cord into the connector on the back of power supply, and connect the other end of the power cord to a properly grounded electrical outlet. 9.
Removing a voltage regulator module 1 2 3 Microprocessor 2 VRM Heat sink 2 VRM connector To remove a voltage regulator module (VRM), do the following: 1. Read the safety information (see Chapter 2, “Safety information,” on page 5). 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Carefully turn the server on its side so that it is lying flat, with the cover facing up. Attention: Do not allow the server to fall over. 4.
Installing a voltage regulator module 1 2 3 Microprocessor 2 VRM Heat sink 2 VRM connector To install a voltage regulator module, do the following: 1. Locate the VRM connector on the system board, next to the heat sink for microprocessor 2 (see “System-board internal connectors” on page 131). 2. Open the retaining clips on each end of the VRM connector. 3. Turn the VRM so that the keys align with the connector. 4.
3. Unlock and remove the side cover (see “Removing the left-side cover” on page 157). 4. Open the front and rear adapter-retention brackets. 5. Remove all adapters and place the adapters on a static-protective surface (see “Removing an adapter” on page 184). Note: You might find it helpful to note where each adapter is installed before you remove the adapters. 6.
Removing the rear adapter retention bracket 1 2 Rear adapter retention bracket Hinge pin To remove the rear adapter-retention bracket, do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Unlock and remove the side cover (see “Removing the left-side cover” on page 157). 4.
Installing the rear adapter retention bracket 1 2 Rear adapter retention bracket Hinge pins To install the rear adapter retention bracket, do the following: 1. Insert the bottom hinge point on the rear adapter retention bracket into the matching hole in the chassis; then, insert the top hinge point into the matching hole. 2. Install the adapters (see “Installing an adapter” on page 184). 3. Close the rear adapter retention bracket. 4.
Removing an adapter 1 2 3 Rear adapter retention bracket Adapter Front adapter retention bracket To remove an adapter, do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Carefully turn the server on its side so that it is lying flat, with the cover facing up. Attention: Do not allow the server to fall over. 4.
v v v v v Avoid touching the components and gold-edge connectors on the adapter. PCI slots 1 and 6 support half-length PCI adapters only. PCI slots 2, 3, 4, and 5 support full-length and half-length PCI adapters. The PCI Express extender card supports a full-length adapter. The PCI-X extender card supports two full-length adapters. v PCI slots 1 and 5 support the RAID adapters. v PCI slot 2 supports a VGA adapter.
1 2 3 Rear adapter retention bracket Adapter Front adapter retention bracket 6. If you are installing a full-length adapter, remove the blue adapter guide 1 (if any) from the end of the adapter. Otherwise, continue with the next step. 7. Press the adapter firmly into the expansion slot, lower the adapter-retention bracket, and make sure that the bracket is in the closed position. Attention: Incomplete insertion might cause damage to the system board or the adapter. 8.
If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on page 233. Removing the DVD drive To remove the DVD drive 1 , do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Unlock and remove the left-side cover (see “Removing the left-side cover” on page 157). 4. Disconnect the DVD drive cables from the back of the DVD drive. 5.
Installing a DVD (optical) drive To install a DVD (optical) drive 1 , do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices and disconnect the power cords and all external cables. 3. Unlock and remove the left-side cover (see “Removing the left-side cover” on page 157). 4. Install the rails on the sides of the DVD drive. 5. Connect one end of the DVD drive cables to the rear of the DVD drive. 6. Slide the drive into the server. 7.
Removing an optional tape drive 1 2 EMC shield Tape drive To remove an optional tape drive, do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Unlock and remove the left-side cover (see “Removing the left-side cover” on page 157). 4. Open the bezel (see “Opening the bezel” on page 150). 5.
Installing a USB or SATA tape drive The server supports USB and SATA tape drives. When you install a tape drive, be sure to connect the internal tape cable to the correct connector on the system board. To install a tape drive, do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3.
1 2 Fan-cage assembly release buttons Fan-cage assembly a. Press the fan-cage release latches on the top and bottom of the fan cage toward the sides of the server. The cage lifts slightly when the release latches are fully open. b. Grasp the cage and lift it out of the server. Chapter 7.
14. If the tape drive came with screws, secure the drive to the server chassis, using the supplied screws. 1 2 3 4 5 SATA optical drive power connector USB signal cable connector USB signal cable SATA optical drive power cable (SATA-to-traditional power connector cable also included. Not pictured.) SATA optical drive signal cable 15.
If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on page 233. | Removing the USB cable and EasyLED panel 1 Spring clips To remove the USB cable and EasyLED panel from the server, complete the following steps: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices; then, disconnect the power cords and all external cables. 3.
15. Disconnect the USB cable from the USB cable and EasyLED panel: a. Rotate the USB cable and EasyLED panel mounting bracket so that you are looking at the rear of the bracket. b. Squeeze the retaining clips on each side of the USB cable connector and pull the USB cable away from the mounting bracket. 16. If you are instructed to return the USB cable and EasyLED panel, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
6. Install the fan-cage assembly (see “Installing the fan-cage assembly” on page 172). 7. Install the air baffle (see “Installing the air baffle” on page 170). 8. Return the power-supply cage to its closed position (see “Closing the power-supply cage” on page 160). 9. Install the hot-swap power supply or power supplies (see “Installing a hot-swap power supply” on page 175). 10. Install the bezel (see “Installing the bezel” on page 154). 11.
3. Press down on the release latch to open the drive handle; then, pull the drive out of the drive bay. 4. If you are instructed to return the hot-swap hard disk drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a 2.
v Make sure that the drive is correctly installed in the drive bay. v See the documentation for the ServeRAID controller for instructions for installing a hard disk drive. v All hot-swap drives in the server must have the same throughput speed rating; using drives with different speed ratings might cause all drives to operate at the throughput of the slowest drive. v You do not have to turn off the server to install hot-swap drives in the hot-swap drive bays.
Notes: a. After installing the hard disk drive, check the disk drive status LEDs to verify that the hard disk drive is operating correctly. If the amber hard disk drive status LED is lit continuously, that drive is faulty and must be replaced. If the green hard disk drive activity LED is flashing, the drive is being accessed. b. If the server is configured for RAID operation using an optional ServeRAID adapter, you might have to reconfigure your disk arrays after you install hard disk drives.
5. Remove the hot-swap hard disk drives (see “Removing a 2.5-inch hot-swap hard disk drive” on page 195). 6. Remove the power supply or power supplies from the power-supply cage (see “Removing a hot-swap power supply” on page 174). 7. Rotate the power-supply cage to its open position (see “Opening the power-supply cage” on page 158). 8. Remove the air baffle (see “Removing the air baffle” on page 169). 9. Remove the fan-cage assembly (see “Removing the fan-cage assembly” on page 171). 10.
Installing a 2.5-inch disk drive backplane 1 2 3 4 5 6 7 Latch Tabs Configuration cable connector SAS signal cable connector 2.5-inch hot-swap backplane Power cable connector Locator pin To install a 2.5-inch hard disk drive backplane, complete the following steps: 1. Touch the static-protective package that contains the hard disk drive backplane to any unpainted metal surface on the server; then, remove the backplane from the package. 2. Position the 2.
10. Install the power supplies (see “Installing a hot-swap power supply” on page 175). 11. Install and lock the left-side cover (see “Installing the left-side cover” on page 158). 12. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Chapter 7.
Removing the 2.5-inch disk drive cage 1 2 2.5-inch hard disk drive cage 2.5-inch hot-swap drive To remove the 2.5-inch hard disk drive cage, complete the following steps. 1. Read the safety information that begins on page 5.. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Carefully turn the server on its side so that it is lying flat, with the cover facing up. Attention: Do not allow the server to fall over. 4.
13. Remove both of the backplanes from the 2.5-inch disk drive cage (see “Removing a 2.5-inch disk drive backplane” on page 198). 14. If you are instructed to return the 2.5-inch disk drive cage, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Chapter 7.
Installing the 2.5-inch disk drive cage 1 2 2.5-inch hard disk drive cage 2.5-inch hot-swap drive To install a 2.5-inch hard disk drive cage, complete the following steps: 1. Touch the static-protective package that contains the 2.5-inch disk drive cage to any unpainted metal surface on the server; then, remove the drive cage from the package. 2. Install both 2.5-inch disk drive backplanes in the back of the drive cage (see “Installing a 2.5-inch disk drive backplane” on page 200). 3. Slide the 2.
12. Install and lock the left-side cover (see “Installing the left-side cover” on page 158). 13. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing the operator information panel assembly 1 2 Release latch Control panel assembly To remove the operator information panel assembly, complete the following steps: 1. Read the safety information that begins on page 5. 2.
11. Push up on the release latch while you pull the operator information panel assembly toward the rear of the server; then, angle the back of the assembly toward the system board and remove the assembly from the server. 12. If you are instructed to return the operator information panel assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
9. Close the bezel (see “Closing the bezel” on page 151). 10. Install and lock the left-side cover (see “Installing the left-side cover” on page 158). 11. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing an extender card 1 Extender card retaining screws To remove an extender card, complete the following steps: 1. Read the safety information that begins on page 5. 2.
4. Unlock and remove the side cover (see “Removing the left-side cover” on page 157). 5. Remove any adapters that are installed in the expansion slots (see “Removing an adapter” on page 184). 6. Remove the system board and place it on a static-protective surface (see “Removing the system board” on page 231). Note: Do not remove the DIMMs, heat sinks, microprocessors, VRM, or battery from the system board. 7. Remove the two screws that secure the extender card to the system-board tray. 8.
Installing an extender card 1 Extender card retaining screws To install an extender card, complete the following steps: 1. Touch the static-protective package that contains the extender card to any unpainted metal surface on the server; then, remove the extender card from the package. 2. Align the extender card with its connector on the system board; then, slide the extender card into the connector. 3. Install the two screws that secure the extender card to the system-board tray. 4.
7. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing a memory module 1 2 DIMM Retaining clip To remove a dual inline memory module (DIMM), do the following: 1. Read the safety information that begins on page 5. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Turn the server on its side so that it is lying flat, with the cover facing up. 4.
Installing a memory module The following notes describe the types of dual inline memory modules (DIMMs) that your server supports and other information that you must consider when you install DIMMs. 1 2 Microprocessor 1 Microprocessor 2 v The server supports industry-standard double-data-rate 3 (DDR3), 800, 1066, or 1333 MHz, PC3-10600R-999 (single-, dual-, or quad-rank), registered, synchronous dynamic random-access memory (SDRAM) dual inline memory modules (DIMMs) with error correcting code (ECC).
v The server supports 1 GB, 2 GB, and 4 GB DIMMs, with a minimum of 1 GB and a maximum of 64 GB of system memory. For 32-bit operating systems only: Some memory is reserved for various system resources and is unavailable to the operating system. The amount of memory that is reserved for system resources depends on the operating system, the configuration of the server, and the configured PCI devices. v The maximum operating speed of the server is determined by the slowest DIMM in the server.
following illustration shows that the first pair of DIMMs (indicated by ones (1) inside the boxes) should be installed in DIMM connector 3 on channel 0 and DIMM connector 6 on channel 1. DIMM connectors 7, 8, 15, and 16 on channel 2 are not used in memory-mirroring mode. Figure 1. Memory channel interface layout 1 2 3 CPU 1 CPU 2 QPI The following table lists the DIMM connectors on each memory channel. Table 12.
Figure 2. Memory connectors associated with each microprocessor 1 2 CPU 1 CPU 2 The following table lists the installation sequence for installing DIMMs in memory-mirroring mode. Table 13.
The following illustration shows how to install DIMMs on the system board. Attention: Static electricity that is released to internal server components when the server is powered on might cause the server to stop, which might result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when you work inside the server with the power on. To install a DIMM, do the following: 1. Read the safety information that begins on page 5. 2.
1 2 DIMM Retaining clip 10. Insert the DIMM into the connector by aligning the edges of the DIMM with the slots at the ends of the DIMM connector. Firmly press the DIMM straight down into the connector by applying pressure on both ends of the DIMM simultaneously. The retaining clips snap into the locked position when the DIMM is firmly seated in the connector.
Removing a hot-swap fan The server comes with three 120 mm x 38 mm hot-swap fans in the fan support bracket at the front of the server. The following instructions can be used to remove any hot-swap fan in the server. 1 Hot-swap fan To remove a hot-swap fan, do the following: 1. Read the safety information that begins on page 5.
Installing a hot-swap fan The server comes with three 120 mm x 38 mm hot-swap fans in the fan support bracket at the front of the server. The following instructions can be used to install any hot-swap fan in the server. 1 Hot-swap fan To install a hot-swap fan, do the following: 1. Read the safety information that begins on page 5.
5. Remove the power supply or power supplies from the power-supply cage (see “Removing a hot-swap power supply” on page 174). 6. Rotate the power-supply cage to its open position (see “Opening the power-supply cage” on page 158). 7. Remove the air baffle (see “Removing the air baffle” on page 169). 8. Remove the microprocessor heat sink: a. Lift the heat-sink release lever to the fully open position. b. Rotate the back of the heat sink out of the retention bracket and remove the heat sink from the server.
1 2 3 Microprocessor release latch Microprocessor bracket frame Microprocessor 10. If you are removing microprocessor 2, remove the voltage regulator module (VRM) from the connector next to microprocessor socket 2. a. Open the retaining clips on each end of the VRM connector. b. Pull the VRM out of the connector. 11. If you are instructed to return the microprocessor, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
v (Optional) Obtain an SMP-capable operating system. For a list of supported operating systems and optional devices, see http://www.lenovo.com/thinkserver. v To order additional microprocessor optional devices, contact your Lenovo marketing representative or authorized reseller. v The microprocessor speeds are automatically set for this server; therefore, you do not have to set any microprocessor frequency-selection jumpers or switches. v If you have to replace a microprocessor, call for service.
2. Open the microprocessor socket by pressing down on the end of the release lever, moving it to the side, and slowly releasing it to the open (up) position. 1 2 3 4 Microprocessor Alignment triangles Notches Microprocessor bracket frame 3. Open the microprocessor bracket frame and remove the microprocessor filler, if one is installed. Attention: a. Do not touch the microprocessor contacts; handle the microprocessor by the edges only.
1 2 3 Microprocessor release latch Microprocessor bracket frame Microprocessor 6. Install a heat sink on the microprocessor. Attention: Do not touch the thermal grease on the bottom of the heat sink or set down the heat sink after you remove the plastic cover. Touching the thermal grease will contaminate it. If the thermal grease is contaminated, call Lenovo service to request a replacement thermal grease kit.
1 2 3 4 5 6 7 Heat sink flange Microprocessor Release level locking tab Retainer bracket Alignment tab Heat sink release level Notch Attention: The heat sink is keyed to the retention module. Make sure that the notch on the heat sink fits over the alignment tab on the retention module. d. Align the notch on the heat sink with the alignment tab on the retainer module. e. Slide the rear flange of the heat sink into the opening in the retainer bracket. f.
9. Return the power-supply cage to its closed position (see “Closing the power-supply cage” on page 160). 10. Install the power supplies (see “Installing a hot-swap power supply” on page 175). 11. Install and lock the left-side cover (see “Installing the left-side cover” on page 158). 12. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Chapter 7.
Thermal grease The thermal grease must be replaced whenever the heat sink has been removed from the top of the microprocessor and is going to be reused or when debris is found in the grease. To replace damaged or contaminated thermal grease on the microprocessor and heat sink, complete the following steps: 1. Place the heat sink on a clean work surface. 2. Remove the cleaning pad from its package and unfold it completely. 3. Use the cleaning pad to wipe the thermal grease from the bottom of the heat sink.
Removing a heat-sink retention module 1 Alignment triangle To remove a heat-sink retention module, complete the following steps: 1. Read the safety information that begins on page 5. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Carefully turn the server on its side so that it is lying flat, with the cover facing up. Attention: Do not allow the server to fall over. 4.
Installing a heat-sink retention module 1 Alignment triangle To install a heat-sink retention module, complete the following steps: 1. Place the heat-sink retention module in the microprocessor location on the system board. 2. Using a Phillips screwdriver, install the four screws that secure the module to the system board. 3. Install the heat sink (see “Installing a microprocessor and heat sink” on page 220). Attention: Make sure that you install each heat sink with its paired microprocessor. 4.
Removing a microprocessor retention module To remove a microprocessor retention module, complete the following steps: 1. Read the safety information that begins on page 5. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Carefully turn the server on its side so that it is lying flat, with the cover facing up. Attention: Do not allow the server to fall over. 4. Unlock and remove the side cover (see “Removing the left-side cover” on page 157). 5.
Installing a microprocessor retention module To install a microprocessor retention module, complete the following steps: 1. Orient the triangle-shaped indicator on one corner of the microprocessor retention module to the corresponding alignment triangle on the system board; then, place the retention module on the system board. 2. Using a T8 Torx screwdriver, install the four screws that secure the module to the system board. 3.
Removing the system board 1 2 Handle Release lever To remove the system board, complete the following steps: 1. Read the safety information that begins on page 5. 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Carefully turn the server on its side so that it is lying flat, with the cover facing up. Attention: Do not allow the server to fall over. 4. Unlock and remove the side cover (see “Removing the left-side cover” on page 157). 5.
10. Remove any of the following components that are installed on the system board and put them in a safe, static-protective place: v Adapters (see “Removing an adapter” on page 184). v Extender card (see “Removing an extender card” on page 207). v DIMMs (see “Removing a memory module” on page 210). v Microprocessors and heat sinks (see “Removing a microprocessor and heat sink” on page 218). v Battery (see “Removing the battery” on page 172). 11. Rotate the release lever toward the front of the chassis. 12.
1. Touch the static-protective package that contains the system board to any unpainted metal surface on the server; then, remove the system board from the package. 2. Hold the system board by the handles and insert the system board into the chassis at an angle; then, slide it toward the rear of the server. 3. 4. 5. 6. 7. 8. 9. 10. 11. Note: Make sure that none of the server cables are caught under the system board.
Connecting the cables Notes: 1. Be sure to turn off the server before you connect any cables to or disconnect any cables from the server or hot-plug adapter. 2. For additional cabling instructions, see the documentation that comes with the optional devices. It might be easier for you to route any cables before you install certain optional devices. 3. Cable identifiers are printed on the cables that come with the server and optional devices.
Some optional devices have device drivers that you must install. For information about installing device drivers, see the documentation that comes with each device. The server comes with at least one microprocessor. If more than one microprocessor is installed, the server can operate as a symmetric multiprocessing (SMP) server. You might have to upgrade the operating system to support SMP. For more information, see “Typical operating system installation” on page 265 and the operating-system documentation.
236 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Chapter 8. Parts Listing, TD200x Machine Types 3719, 3821, 3822, and 3823 The following replaceable components are available for the ThinkServer TD200x Types 3719, 3821, 3822, and 3823 servers. To check for an updated parts listing on the Web, complete the following steps: 1. Go to: http://www.lenovo.com/support. 2. Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. 3. From Family list, select ThinkServer TD200x, and click Continue.
Table 14. Parts listing, Type 3719 Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 1 Side Cover (models CTO All Models) 46D1389 2 Retention Module (models CTO All Models) 46D1397 3 Air Duct (models CTO All Models) 46D1409 4 CPU Heat sink (models CTO All Models) 46D1407 5 Microprocessor, Xeon 2.66GHz/6.4GTS-8MB QC 95w (models CTO) 46D1264 5 Microprocessor, Xeon 2.4GHz/5.86GTS-8MB QC 80w (models CTO) 46D1266 5 Microprocessor, Xeon 2.26GHz/5.
Table 14. Parts listing, Type 3719 (continued) Index CRU part number (Tier 1) Description 19 Hard disk drive, 73GB 15K SFF 6Gbps HS HDD (models CTO All Models) 46U2128 20 2.
Table 14.
Table 15. Parts listing, Type 3821 (continued) Index CRU part number (Tier 1) Description CRU part number (Tier 2) 15 Half-High SATA DVD-ROM (models CTO) 43W8466 15 Half-High SATA Multi-Burner (models CTO) 43W8467 16 TD200x Bezel FRU (models CTO All Models) 46U2424 17 EMC Shield 4 x 3.
Table 15. Parts listing, Type 3821 (continued) Index Description CRU part number (Tier 1) Chassis (models CTO All Models) 46D1408 Hot Swap Fan Cage (models CTO All Models) 46D1410 Top/Side cover (models CTO All Models) 46D1411 ALCOHOL WIPE (models CTO All Models) 59P4739 Bottom Cover - TD200(x) Rack (models CTO All Models) 46C6704 Keyboard,. USEng103P (models CTO) 41A5100 Mouse, Opt.
Table 16.
Table 16.
Table 17. Parts listing, Type 3823 Index CRU part number (Tier 1) Description CRU part number (Tier 2) FRU part number 1 Side Cover (models CTO All Models) 46D1389 2 Retention Module (models CTO All Models) 46D1397 3 Air Duct (models CTO All Models) 46D1409 4 CPU Heat sink (models CTO All Models) 46D1407 5 Microprocessor, Xeon 2.66GHz/6.4GTS-8MB QC 95w (models CTO) 46D1264 5 Microprocessor, Xeon 2.4GHz/5.86GTS-8MB QC 80w (models CTO) 46D1266 5 Microprocessor, Xeon 2.26GHz/5.
Table 17. Parts listing, Type 3823 (continued) Index Description CRU part number (Tier 1) 19 Hard disk drive, 73GB 15K SFF 6Gbps HS HDD (models CTO All Models) 46U2128 20 2.
Table 17.
Table 18. Power cords, Type 3719 (continued) Lenovo Power cord part number Used in these countries and regions 39M5144 South Africa 2.8M (models CTO 45G 45M 45A) 39M5151 UK 2.8M (models CTO) 39M5158 Switzerland 2.8M (models CTO 45S 45G) 39M5165 Italy 2.8M (models CTO 45Y 45G) 39M5172 Israel 2.8M (models CTO 45G) 39M5081 US/Canada 2.8M (models CTO 45U 45S 45A 45T 45H 45V) 39M5219 Korea 2.8M (models CTO 45R) 39M5199 Japan 2.8M (models CTO 45E) 39M5068 Argentina 2.
Table 20. Power cords, Type 3822 (continued) Lenovo Power cord part number Used in these countries and regions 39M5144 S. Africa 2.8M (models CTO 41G 41M 41A 42G 42M 42A 43G 43M 43A 44G) 39M5151 UK 2.8M (models CTO 41G 41A 42G 42A 43G 43A) 39M5158 Switzerland 2.8M (models CTO 41Y 41G 42Y 42G 43Y 43G) 39M5165 Italy 2.8M (models CTO 41S 41G 42S 42G 43S 43G) 39M5172 Israel 2.8M (models CTO 41G 42G 43G) 39M5081 US/Canada 2.8M (models CTO 41U 41A 41T 42U 42A 42T 43U 43A 43T) 39M5219 Korea 2.
250 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Chapter 9. Configuring the server The following configuration programs come with the server: v Setup Utility The Setup Utility (formerly called the Configuration/Setup Utility program) is part of the server firmware. Use it to change the startup-device sequence, set the date and time, and set passwords. For information about using this program, see “Using the Setup Utility” on page 252. v Boot Menu program The Boot Menu program is part of the server firmware.
| | Table 22.
Utility, the changes are reflected in the system summary; you cannot change settings directly in the system summary. – Product Data Select this choice to view the system-board identifier, the revision level or issue date of the firmware, the integrated management module and diagnostics code, and the version and date. v System Settings Select this choice to view or change the server component settings. – Processors Select this choice to view or change the processor settings.
- Network Configuration Select this choice to view the system management network interface port, the IMM MAC address, the current IMM IP address, and host name; define the static IMM IP address, subnet mask, and gateway address; specify whether to use the static IP address or have DHCP assign the IMM IP address; save the network changes. - Reset IMM to Defaults Select this choice to view or reset IMM to the default settings.
v User Security Select this choice to set, change, or clear passwords. See “Passwords” for more information. This choice is on the full and limited Setup Utility menu. – Set Power-on Password Select this choice to set or change a power-on password. For more information, see “Power-on password” on page 256. – Clear Power-on Password Select this choice to clear a power-on password. For more information, see “Power-on password” on page 256.
password has access to only the limited Setup Utility menu; the user can set, change, and delete the power-on password, if the system administrator has given the user that authority. Power-on password If a power-on password is set, when you turn on the server, the system startup will not be completed until you type the power-on password. You can use any combination of up to seven characters (A - Z, a - z, and 0 - 9) for the password.
v Change the position of the power-on password switch (enable switch 2 of the system board switch block (SW6)) to bypass the power-on password check (see the following illustration). 1 2 3 UEFI boot recovery jumper (JP6) Clear CMOS jumper (JP1) SW6 switch block Attention: Before you change any switch settings or moving any jumpers, turn off the server; then, disconnect all power cords and external cables. See the safety information that begins on page 5.
Using the Boot Selection Menu program The Boot Selection Menu is used to temporarily redefine the first startup device without changing boot options or settings in the Setup Utility. To use the Boot Selection Menu program, do the following: 1. Turn off the server. 2. Restart the server. 3. Press F12 (Select Boot Device). If a bootable USB mass storage device is installed, a submenu item (USB Key/Disk) is displayed. 4.
Table 23. RAID utilities (continued) RAID configuration utility Description LSI Logic MPT Setup For: Utility v ServeRAID-BR10i controller Location In system firmware. To access: v Use UEFI Setup Utility. v ServeRAID-BR10ie v Press Ctrl + C at controller the LSI prompt during startup.
v If you install a different type of RAID controller, see the documentation that comes with the controller for information about viewing and changing settings for attached devices. Starting the LSI Configuration Utility program To start the LSI Configuration Utility program, do the following: 1. Turn on the server. 2. 3. 4. 5. 6. Note: Approximately 3 minutes after the server is connected to ac power, the power-control button becomes active. When the prompt Setup is displayed, press F1.
8. Exit the Setup Utility. Using the WebBIOS utility The WebBIOS configuration utility enables you to create and manage RAID configurations on LSI SAS controllers. The WebBIOS utility resides in the SAS controller BIOS and operates independently of the operating system. The WebBIOS utility provides a configuration wizard to guide you through the configuration of virtual disks and physical arrays.
Creating a storage configuration using the Configuration Wizard Follow these steps to start create a storage configuration: 1. Click Configuration Wizard to start the wizard. 2. Select a configuration option: Attention: If you select Clear Configuration or New Configuration, all existing data in the configuration is deleted. Make a backup copy of any data that you want to keep before selecting these options. Clear Configuration Clears the existing configuration.
Using the ThinkServer EasyStartup DVD The ThinkServer EasyStartup DVD simplifies the process of configuring your RAID controller and installing an operating system. The program works in conjunction with your Windows or Linux operating-system installation disc to automate the process of installing the operating system and associated device drivers. If you did not receive a ThinkServer EasyStartup DVD with your server, you can download an image from the Lenovo Support Web site at http://www.lenovo.
v Manually remove the drives that you do not want included in your array before you configure your RAID controller through the EasyStartup program. This method enables you to use the EasyStartup program to configure your RAID controller and install the operating system. After the operating system is installed, reinstall the drives and use the RAID configuration utility provided in the firmware to configure the secondary RAID.
If you continue to the main program interface, you will have the following selectable options: v Compatibility notes: This selection provides information about the operating systems and server configurations supported by that version of the EasyStartup program. v User Guide: This selection provides information about the features provided by that version of the EasyStartup program. v Hardware list: This selection displays a list of hardware devices detected by the EasyStartup program.
v Start installation: This task starts the actual installation process. First, the disk is prepared using the disk and partition information you specified. Then you are prompted to insert the operating system disk, and the operating system is installed using the information that you specified.
Updating the firmware The firmware in the server is periodically updated and is available for download on the Lenovo Support Web site. Go to http://www.lenovo.com/support to check for the latest level of firmware, such as unified extensible firmware interface (UEFI) code, vital product data (VPD) code, device drivers, and service processor firmware.
Starting the backup server firmware The system board contains a backup copy area for the server firmware. This is a secondary copy of server firmware that you update only during the process of updating server firmware. If the primary copy of the server firmware becomes damaged, use this backup copy. To force the server to start from the backup copy, turn off the server; then, place the UEFI boot recovery J29 jumper in the backup position (pins 2 and 3).
v Power/Reset control (power-on, hard and soft shut down, hard and soft reset, schedule power control) v Alerts (in-band and out-of-band alerting, PET traps - IPMI style, SNMP, e-mail) v Operating system failure blue screen capture v Command line interface v Configuration save and restore v PCI configuration data v Boot sequence manipulation The IMM also provides the following remote server management capabilities: v Command-line interface (IPMI Shell) The command-line interface provides direct access to se
Note: Approximately 3 minutes after the server is connected to ac power, the power-control button becomes active. 2. When the prompt Setup is displayed, press F1. If you have set both a power-on password and an administrator password, you must type the administrator password to access the full Setup Utility menu. 3. From the Setup Utility main menu, select System Settings. 4. 5. 6. 7. On the next screen, select Integrated Management Module. On the next screen, select Network Configuration.
Use the command-line interface to issue setup commands. You can save any of the settings as a file and run the file as a script. The ASU program supports scripting environments through a batch-processing mode. Installing ThinkServer EasyManage software You can install the ThinkServer EasyManage Core Server program from the ThinkServer EasyManage CD or you can download and install the program from http://www.lenovo.com/support.
5. (For both Windows Server 2003 and 2008) Download Microsoft Web Services Enhancement 2.0 Service Pack 3 (LANDesk Process Manager only) from the following Web site: http://www.microsoft.com/downloads/ details.aspx?FamilyID=1ba1f631-c3e7-420a-bc1e-ef18bab66122 &DisplayLang=en. Install the software using the default settings. Note: This specific version is required. 6. Use Windows Update to install all available critical updates. 7. Launch the EasyManage installation. 8.
4. Select the checkbox next to Web Server (IIS). A dialog box displays the additional features that are required. 5. Click Add Required Features, then click Next. In the list of additional role services that can be installed, ensure that the follow are checked: v HTTP Redirection v Static Content v ASP.NET v ASP v CGI v Server Side Includes v Windows Authentication v IIS 6 Metabase Compatibility Note: When you select ASP.Net or ASP, a dialog box displays the additional role services required.
274 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Appendix A. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This section contains information about where to go for additional information about Lenovo and Lenovo products, what to do if you experience a problem with your system, and whom to call for service, if it is necessary.
These items are not covered by the warranty: v Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts v Identification of software problem sources v Configuration of BIOS as part of an installation or upgrade v Changes, modifications, or upgrades to device drivers v Installation and maintenance of network operating systems (NOS) v Installation and maintenance of application programs Refer to the safety and warranty information that is provided with your computer for a co
Purchasing additional services During and after the warranty period, you can purchase additional services, such as support for hardware, operating systems, and application programs; network setup and configuration; upgraded or extended hardware repair services; and custom installations. Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at http://www.lenovo.com/. Lenovo product service Appendix A.
278 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Lenovo makes no representation or warranties regarding non-Lenovo products and services, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. These products are offered and warranted solely by third parties. Some software might differ from its retail version (if available) and might not include user manuals or all program functionality.
L’etiquette du système respecte la Directive européenne 2002/96/EC en matière de Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les dispositions de retour et de recyclage applicables aux systèmes utilisés à travers l’Union européenne. Conformément à la directive, ladite étiquette précise que le produit sur lequel elle est apposée ne doit pas être jeté mais être récupéré en fin de vie.
Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo.com/lenovo/environment or contact your local waste disposal facility. For Taiwan: Please recycle batteries.
batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt récupérée en fin de cycle de vie selon cette norme. In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life. The label on the battery may also include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury, and Cd for cadmium).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Class A emission compliance statement This Class A digital apparatus complies with Canadian ICES-003.
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG (früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022 Klasse A ein. Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden.
Japan Voluntary Control Council for Interference (VCCI) statement Taiwan Class A warning statement People’s Republic of China Class A warning statement Korea Class A warning statement Appendix B.
288 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Hardware Maintenance Manual
Index Numerics 2.5-inch disk drive backplane installing 200 removing 198 2.
dc power LED 130 deassertion event, system-event log 28 diagnostic error codes 91 on-board programs, starting 90 programs, overview 90 test log, viewing 91 text message format 90 tools, overview 27 diagnostics program, preboot 15 dimensions 18 DIMM installation 215 installation order 215 LED 85, 136 problems 68 removing 210 types and installation information 211 DIMMs installation sequence for memory mirroring display problems 70 drives 16, 18 DSA log 28, 91 preboot messages 91 DVD drive problems 64 drive,
G general problems 65 getting help 275 gigabit Ethernet controller, configuring gloss statement (Germany) 284 grease, thermal 226 266 H H8 heartbeat LED 87, 138 hard disk drive backplane connectors 147 diagnostic tests, types of 66 formatting 260 installing 197 LED 80 problems 65 removing 195 types 196 heat output 18 heat-sink retention module installing 228 removing 227 help, getting 275 hints and tips 25 humidity 18 I IMM error messages 38 event log 28 heartbeat LED 87, 137 overview 15 installation ord
open bezel 150 opening power-supply cage 158 operator information panel assembly, installing 206 assembly, removing 205 LEDs 76 optical drive 188 optional device problems 72 order of installation, memory modules left-side cover installing 158 local area network (LAN) 16 LOG LED 78 logs system event message 38 LSI Configuration Utility overview 259 starting 260 M management, systems 15 media door, open 155 MEM LED 81 memory 16, 18 memory mirroring description 212 DIMM population sequence 214 memory module
problems (continued) mouse 67 optional devices 72 POST 30 power 73, 123 serial port 74 software 75 undetermined 124 USB port 75 R RAID array, creating 260 rear adapter retention bracket installing 183 removing 182 rear view 130 recovering BIOS update failure 122 UEFI update failure 122 redundant power and cooling option 177 remote presence feature functions 15 using 269 removing 2.5-inch disk drive backplane 198 2.
turning on the server 147 TÜV gloss statement 284 U UEFI update failure 122 undetermined problems 124 undocumented problems 25 United States electronic emission Class A notice United States FCC Class A notice 284 Universal Serial Bus (USB) problems 75 updating server configuration 251 updating firmware 267 updating the server configuration 234 USB port problems 75 USB cable and EasyLED panel installing 194 removing 193 USB connectors 130 USB or SATA tape drive 190 using boot selection menu program 258 Easy
Part Number: XXXXXX Printed in USA (1P) P/N: XXXXXX
