Installation and User Guide ThinkServer TD200 Machine Types: 3724, 3808, 3809, 3815, 3817, 3824, 3826, and 3836
ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836 Installation and User Guide
Note: Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 191 and the Warranty and Support Information document on ThinkServer Documentation DVD. First Edition (June 2009) © Copyright Lenovo 2009. Portions © Copyright International Business Machines Corporation 2009.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1 Notices and statements in this document . . . . . . . . . . . . . . . . 2 Related documentation . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 2. Server setup roadmap . . . . . . . . . . . . . . . . . . 5 Chapter 3. What is included with your server . Features and technologies . . . . . . . . . Specifications . . . . . . . . . . . . . . Software . . . . . .
iv Removing and installing drives . . . . . . . . . . . . . . . . Removing a DVD drive . . . . . . . . . . . . . . . . . . Installing a DVD drive . . . . . . . . . . . . . . . . . . Removing an optional tape drive . . . . . . . . . . . . . . Installing an optional tape drive . . . . . . . . . . . . . . . Removing a 2.5-inch hot-swap hard disk drive . . . . . . . . . Installing a 2.5-inch hot-swap hard disk drive . . . . . . . . . . Removing a 3.5-inch hot-swap hard disk drive . . . . . . . . .
EasyStartup overview . . . . . . . . . . . . . . . Installing your operating system without using EasyStartup . Using the Boot Manager program . . . . . . . . . . . Enabling the Broadcom Gigabit Ethernet Utility program . . . Configuring the Broadcom Gigabit Ethernet controller . . . . Updating the firmware . . . . . . . . . . . . . . . . Starting the backup server firmware . . . . . . . . . . Recovering the server firmware . . . . . . . . . . . Automated boot recovery (ABR) . . . . . . . . . . . .
Lenovo product service . . . . . . . . . . . . . . . . . . . . . 189 Appendix B. Notices . . . . . . . . . . . . . . . . . . . . . Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . Important notes . . . . . . . . . . . . . . . . . . . . . . . Product recycling and disposal . . . . . . . . . . . . . . . . . Compliance with Republic of Turkey Directive on the Restriction of Hazardous Substances . . . . . . . . . . . . . . . . . . . . . . . . Recycling statements for Japan . . . . . . . . . . . . . .
Safety Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Lees voordat u dit product installeert eerst de veiligheidsvoorschriften. Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information. Avant d’installer ce produit, lisez les consignes de sécurité.
Important: All caution and danger statements in this documentation begin with a number. This number is used to cross reference an English caution or danger statement with translated versions of the caution or danger statement in the Safety Information book. For example, if a caution statement begins with a number 1, translations for that caution statement appear in the Safety Information document under statement 1.
Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product. v When possible, use one hand only to connect or disconnect signal cables.
Statement 2: CAUTION: When replacing the lithium battery, use only a battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. v Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
Statement 4: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. Statement 11: CAUTION: The following label indicates sharp edges, corners, or joints nearby.
Statement 13: DANGER Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch circuit protection requirements. Refer to the information that is provided with your device for electrical specifications. Statement 15: CAUTION: Make sure that the rack is secured properly to avoid tipping when the server unit is extended.
Statement 26: CAUTION: Do not place any object on top of rack-mounted devices. This server is suitable for use on an IT power-distribution system whose maximum phase-to-phase voltage is 240 V under any distribution fault condition. Important: This product is not suitable for use with visual display workplace devices according to Clause 2 of the German Ordinance for Work with Visual Display Units.
xvi ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Chapter 1. Introduction This Installation and User Guide contains information and instructions for setting up your ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836 server, instructions for installing optional devices, and instructions for cabling and configuring the server. For removing and installing optional devices, diagnostics and troubleshooting information, see the Hardware Maintenance Manual.
The model number and serial number are on the lower right side of the bezel. 1 Note: The illustrations in this document might differ slightly from your hardware. The server comes with the ThinkServer EasyStartup DVD to help you configure the hardware and install the operating system. Important: The server keys cannot be duplicated by a locksmith. If you lose them, order replacement keys from the key manufacturer.
v Danger: These statements indicate situations that can be potentially lethal or extremely hazardous to you. A danger statement is placed just before the description of a potentially lethal or extremely hazardous procedure step or situation. Related documentation The Lenovo ThinkServer Documentation DVD contains documentation for the server in Portable Document Format (PDF). The Lenovo ThinkServer Documentation DVD requires Adobe® Acrobat Reader 5.
4 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Chapter 2. Server setup roadmap The installation process varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configured and just needs to be installed in the rack, connected to power and the network, and started. In other cases, the server needs to have hardware features installed, requires hardware and firmware configuration, and required the operating system to be installed.
6 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Chapter 3. What is included with your server The TD200 server package includes the server, power cords, and the ThinkServer Documentation DVD.
Note: The server does not support Disk Operating System (DOS). v Preboot diagnostics program The preboot diagnostics programs are stored on the integrated USB memory. They collect and analyze system information to aid in diagnosing server problems.
Some models support memory mirroring. Memory mirroring replicates and stores data on two pairs of DIMMs within two channels (channel 0 and 1) simultaneously. If a failure occurs, the memory controller switches from the primary pair of memory DIMMs to the backup pair of DIMMs. To support memory mirroring, you must install a pair of DIMMs at a time. One DIMM must be in channel 0, and the mirroring DIMM must be in the same slot in channel 1. For more information, see 91.
Table 1. Features and specifications Microprocessor: v Supports up to two Intel® Pentium® dual-core or quad-core microprocessors (one installed) with integrated memory controller and QuickPath Interconnect (QPI) architecture.
Table 1. Features and specifications (continued) Drives (depending on the model): v Optical drives: SATA v Hard disk drives: SAS and SATA Integrated functions: v Integrated Management Module (IMM), which provides service processor control and monitoring functions, video Drive bays (depending on the model): controller, and (when the optional virtual v Three 5.25-in. bays (one half-high media key is installed) remote DVD-ROM drive installed).
Table 1.
Reliability, availability, and serviceability Three important server design features are reliability, availability, and serviceability (RAS). The RAS features help to ensure the integrity of the data that is stored in the server, the availability of the server when you need it, and the ease with which you can diagnose and repair problems.
v Upgradeable microcode for POST, server firmware, and read-only memory (ROM) resident code, locally or over a LAN v Vital product data (VPD); includes serial-number information and replacement part numbers, stored in nonvolatile memory, for easier remote maintenance 14 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Chapter 4. Server controls, LEDs, and power This section describes the controls, light-emitting diodes (LEDs), and connectors on the front and rear of the server, and how to turn the server on and off. For the location of the LEDs on the system board, see “System-board LEDs” on page 33. Note: The illustrations in this document might differ slightly from your model. Front view The following illustrations show the controls, LEDs, and connectors on the front of the server models.
1 2 3 4 5 6 Power-on LED 7 Power-control button 8 Hard disk drive activity LED 9 System-error LED 10 USB 2 11 USB 1 DVD-eject button Hard disk drive activity LED (green) Hard disk drive status LED (amber) DVD drive activity LED (green) Front information panel The following is an illustration of the 3.
1 2 3 4 5 Power-on LED 6 Power-control button 7 Hard disk drive activity LED 8 System-error LED 9 USB 2 10 USB 1 DVD-eject button Simple-swap hard disk drive DVD drive activity LED (green) Information panel Power control button and power-on LED Press this button to turn the server on and off manually or to wake the server from a reduced-power state. The states of the power-on LED are as follows: Off: ac power is not present, or the power supply or the LED itself has failed.
An LED on the system board might also be lit to help isolate the error. Detailed troubleshooting information is in the Hardware Maintenance Manual. USB connectors Connect USB devices to these connectors. DVD-eject button Press this button to release a CD or DVD from the DVD drive. DVD drive activity LED When this LED is lit, it indicates that the DVD drive is in use. Hot-swap hard disk drive activity LED (some models) On some server models, each hot-swap drive has a hard disk drive activity LED.
Operator information panel The following illustration shows the LEDs on the operator information panel on the front of the server. 1 2 3 4 5 System power-on LED Hard disk drive activity LED System-locator LED System-information LED System-error LED v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Rear view The following illustration shows the LEDs and connectors on the rear of the server.
Power-error (Fault) LED When this amber LED is lit, it indicates that the power supply has failed. For any other combination of LEDs, see the Hardware Maintenance Manual. Video connector Connect a monitor to this connector. Note: The maximum video resolution is 1600 x 1200 at 60 MHz. Serial connector Connect a 9-pin serial device to this connector. Systems-management Ethernet connector Use this connector to manage the server, using a dedicated management network.
System-board internal connectors The following illustration shows the internal connectors on the system board.
System-board external connectors The following illustration shows the external input/output (I/O) connectors on the system board. 1 2 3 4 5 Power connector Serial (COM 1) Video Systems-management Ethernet connector NMI button 6 7 8 9 USB 1-2 Ethernet 1 USB 3-4 Ethernet 2 Chapter 4.
System-board option connectors The following illustration shows the system-board connectors for user-installable options.
System-board switches and jumpers The following illustration shows the switches and jumpers on the system board. 1 2 3 UEFI boot recovery jumper (JP8) Clear CMOS jumper (JP1) SW8 switch block The following table describes the jumpers on the system board. Table 2. System-board jumpers Jumper number Jumper name Jumper setting JP1 Clear CMOS jumper v Pins 1 and 2: Normal (default) - This keeps the CMOS data.
Table 2. System-board jumpers (continued) Jumper number Jumper name Jumper setting JP6 UEFI boot recovery jumper v Pins 1 and 2: Normal (default) - Loads the primary server firmware ROM. v Pins 2 and 3: This enables the server to recovery if the server firmware becomes damaged. Notes: v If no jumper is present, the server responds as if the pins are set to 1 and 2. v Do not change the jumper pin position after the server is turned on.
Important: 1. Before you change any switch settings or move any jumpers, turn off the server, then, disconnect all power cords and external cables. Read the safety information (see “Safety” on page vii, “Handling static-sensitive devices” on page 39, and “Working inside the server with the power on” on page 38). 2. Any system-board switch blocks or jumpers that are not shown in the illustrations in this document are reserved.
1 2 3 4 5 6 7 8 Microprocessor mismatch LED Microprocessor 2 error LED DIMMs 9-18 error LEDs DIMMs 1-8 error LEDs Microprocessor 1 error LED System-board error LED Battery error LED IMM heartbeat LED 9 PCI slot 6 error LED 10 11 12 13 14 15 16 PCI slot 5 error LED PCI slot 4 error LED Enclosure manager heartbeat LED PCI slot 3 error LED PCI slot 2 error LED PCI slot 1 error LED VRM error LED For more information about the system-board LEDs, see the Hardware Maintenance
Server power features When the server is connected to an ac power source but is not turned on, the operating system does not run, and all core logic except for the service processor (the Integrated Management Module) is shut down; however, the server can respond to requests to the service processor, such as a remote request to turn on the server. The power-on LED flashes to indicate that the server is connected to ac power but is not turned on.
2 1 The server can be turned off in any of the following ways: v You can turn off the server from the operating system, if your operating system supports this feature. After an orderly shutdown of the operating system, the server will be turned off automatically. v You can press the power-control button to start an orderly shutdown of the operating system and turn off the server, if your operating system supports this feature.
Chapter 5. Installing optional devices and replacing customer replaceable units Important: Before you install optional hardware, make sure that the server is working correctly. Start the server, and make sure that the operating system starts, if an operating system is installed. If the server is not working correctly, see the Hardware Maintenance Manual and “Troubleshooting tables” on page 163 for diagnostic information.
v You do not have to turn off the server to install or replace hot-swap fans and hot-swap drives. v Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the server, open or close a latch, and so on.
v Remove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist watches. v Remove items from your shirt pocket, such as pens and pencils, that could fall into the server as you lean over it. v Avoid dropping any metallic objects, such as paper clips, hairpins, and screws, into the server. Handling static-sensitive devices Attention: Static electricity can damage the server and other electronic devices.
Major components of the server The following illustration shows the major components in the server (depending on the server model). The illustrations in this document might differ slightly from your hardware. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Bezel Optical drive bay EMC shield 2.5-inch EMC shield 3.5-inch EMC shield 2.5-inch hot-swap 3.5-inch hot-swap 3.5-inch simple-swap drive SAS/SATA 2.5-inch backplane SAS/SATA 3.5-inch backplane Simple-swap 3.
Note: You must unlock the side cover to open or remove the bezel. When you lock the server side cover, it locks both the cover and the bezel. 3. Remove the bezel. Position your finger on the depressed area on the left side of the bezel and rotate the bezel away from the server. 4. If you want to remove the bezel completely, press the retention tabs on the hinge assembly toward each other and pull the hinge assembly out of the chassis.
1 2 3 Bezel Hinge assembly Retention tabs Note: The bezel will also disengage from the chassis hinges if you rotate the bezel beyond 180° or if excessive pressure is applied to the bezel. Do not be alarmed because this is how the bezel was designed. The bezel is designed with breakaway hinges so that you can easily reattach it to the chassis. Opening and closing the bezel media door To open the media door, do the following: 1.
4. From inside of the top section of the bezel door, slide the blue tab up to unlock the bezel media door (slide the tab down when you want to lock it); then, grasp the pull-point area on the left side of the media door and pull the door open. Note: To close and lock the bezel media door, rotate the door to the closed position and slide the blue tab down to lock it.
1 2 3 Cover release latch Latch Left-side cover To replace the side cover, see “Installing the side cover” on page 134. Attention: For proper cooling and airflow, replace the cover before turning on the server. Operating the server for extended periods of time (more than 30 minutes) with the cover removed might damage server components. Removing the air baffle To remove the air baffle, do the following: 1.
1 2 Power supply Power-supply handle 8. Remove the air baffle assembly. Press the blue tab (on top of the fan cage) on the air baffle assembly to the left and lift it from the server and set it aside. Note: It might be easier to remove the air baffle if you lift up the plastic tab that is over the DIMMs in the rear of the server. 1 2 Air baffle pinch tab Air baffle Chapter 5.
Removing the fan cage assembly Attention: v Replace a hot-swap fan within 30 seconds of removal. v To ensure proper cooling and airflow, do not operate the server for more than 2 minutes with the side cover removed. To remove the front fan cage assembly, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3.
1 2 Fan cage assembly Fan cage assembly release buttons 8. If you are instructed to return the fan cage, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing the fan cage assembly Attention: v Replace a hot-swap fan within 30 seconds of removal. v To ensure proper cooling and airflow, do not operate the server for more than 2 minutes with the side cover removed.
1 2 Fan cage assembly Fan cage assembly release buttons 2. Slide the fan cage into the chassis and press firmly until the fan cage is seated firmly in place. Note: Make sure that both release buttons click into place. 3. Install the air baffle (see “Installing the air baffle” on page 132). 4. Rotate the power-supply cage assembly back into the server. Press the power-supply release tab and rotate the power-supply cage assembly into the chassis.
1 2 Power supply support bracket Power supply release tab 5. Install the side cover (see “Installing the side cover” on page 134). 6. Lock the side cover. 7. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing the front USB connector assembly To remove the front USB connector assembly, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2.
1 2 Power supply Power-supply handle 5. Remove the air baffle (see “Removing the air baffle” on page 44). 6. Remove the fan cage assembly (see “Removing the fan cage assembly” on page 46). 7. Open the bezel. Place your finger on the pull-point area on the left side of the bezel door and rotate it away from the server. 8. Disconnect the front USB cable from the system board, noting the routing of the cable (see “System-board internal connectors” on page 28 for the location of the front USB connector).
9. Press the release tab on the front USB housing; then, tilt the top of the housing away from the chassis and lift the housing out of the chassis. 10. Squeeze the spring clips 1 on the sides of the front USB connector assembly and pull the assembly out of the back of the housing. 11. Pull the front USB cable out of the chassis. 12. If you are instructed to return the front USB connector assembly, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping.
6. Install the fan cage assembly (see “Installing the fan cage assembly” on page 47). Note: Make sure that all cables are routed so that they are not damaged when inserting the fan cage assembly into the server. 7. Install the air baffle (see “Installing the air baffle” on page 132). 8. Rotate the power-supply cage assembly back into the server. Press the power-supply cage release tab and rotate the power-supply cage assembly into the chassis.
4. Open the rear adapter retention bracket. 5. Press the rear adapter retention bracket and release the top hinge point; then, release the other hinge point and remove the bracket from the chassis. 1 2 Rear adapter retention bracket Hinge pins 6. If you are instructed to return the rear adapter-retention bracket, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping.
4. Install the side cover (see “Installing the side cover” on page 134). 5. Lock the side cover, if necessary. 6. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing the front adapter-retention bracket To remove the front adapter-retention bracket, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2.
Statement 2: CAUTION: When replacing the lithium battery, use only a battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble To remove the battery, do the following: 1.
v The lithium battery must be handled correctly to avoid possible danger. If you replace the battery, you must adhere to the following instructions. v You must replace the battery with a lithium battery of the same type from the same manufacturer. v To avoid possible danger, read and follow the following safety statement. Statement 2: CAUTION: When replacing the lithium battery, use only a battery recommended by the manufacturer.
Note: You must wait approximately 1 to 3 minutes after you connect the power cord of the server to an electrical outlet before pressing the power-control button. 6. Start the Setup Utility and reset the configuration. v Set the system date and time. v Set the power-on password. v Reconfigure the server. See “Using the Setup Utility” on page 138 for details. Removing and installing drives Depending on the server model, the server might come with a SATA attached DVD-ROM drive in bay 1.
1 2 3 4 5 6 7 Bay Bay Bay Bay Bay Bay Bay 1 2 3 4 5 6 7 The following illustration shows the location of the drive bays in the 3.5-inch simple-swap SATA hard disk drive server models.
1 2 3 4 5 6 7 Bay Bay Bay Bay Bay Bay Bay 1 2 3 4 5 6 7 The following notes describe the types of drives that the server supports and other information that you must consider when installing a drive: v Make sure that you have all the cables and other equipment that is specified in the documentation that comes with the drive. v Check the instructions that come with the drive to see whether you have to set any switches or jumpers on the drive.
1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3. Unlock and remove the side cover (see “Removing the side cover” on page 43). 4. Open the bezel. Place your finger on the pull-point area on the left side of the bezel door and rotate it away from the server. 5. Rotate the power-supply cage assembly out of the chassis.
1 2 Fan cage assembly Fan cage assembly release buttons 8. Disconnect the power and signal cables from the drive that is to be removed. 9. Press and hold the blue release tabs on each side of the DVD drive to release the drive; then, pull the drive out of the front of the server. 10. Remove the blue optical drive rails 1 from the side of the drive 2 and save the optical rails to use when you install the replacement drive. 11.
Installing a DVD drive To install a DVD drive, do the following: 1. If you are replacing a drive, make sure that: v You have all the cables and other equipment that are specified in the documentation that comes with the new drive. v You have checked the instructions that come with the new drive to determine whether you must set any switches or jumpers in the drive. v You have removed the blue optical drive rails from the side of the old drive and have them available for installation on the new drive.
1 2 Power supply Power-supply handle 3. Remove the air baffle (see “Removing the air baffle” on page 44). 4. Remove the fan cage assembly. Press in on the fan cage assembly release buttons on the sides of the chassis to release the fan cage assembly from the connector on the chassis. Lift the fan cage assembly up and out of the chassis and set it aside. 1 2 Fan cage assembly Fan cage assembly release buttons Chapter 5.
5. Touch the static-protective package that contains the new DVD drive to any unpainted metal surface on the server; then, remove the DVD drive from the package and place it on a static-protective surface. 6. Follow the instructions that come with the drive to set jumpers or switches, if there are any. Note: You might find it easier to install the new drive from the front and then attach the cables. 7.
1 2 Optical drive power cable SATA optical drive signal cable 10. Install the fan cage assembly (see “Installing the fan cage assembly” on page 47). 11. Install the air baffle (see “Installing the air baffle” on page 132). 12. Rotate the power-supply cage assembly back into the server. Press the power-supply cage release tab and rotate the power-supply cage assembly into the chassis. Chapter 5.
1 2 13. 14. 15. 16. Power supply support bracket Power supply release tab Close the bezel. Install the side cover (see “Installing the side cover” on page 134). Lock the side cover. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. If you have other options to install or remove, do so now; otherwise go to “Completing the installation” on page 130. Removing an optional tape drive To remove an optional full-high tape drive, do the following: 1.
and set it aside. 8. Disconnect the tape drive cable from the system board. 9. Remove the screws that secure the tape drive 1 to the server. 10. Gently pull the drive out of the server. 11. If you are instructed to return the tape drive, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing an optional tape drive To install a optional full-high tape drive, do the following: 1. Remove the EMC shields from the drive bay, if installed. 2.
1 2 EMC shield Tape drive 5. If the tape drive comes with screws, secure the tape drive to the chassis with the supplied screws. 6. Connect one of the connectors on the optical drive power cable to the tape drive. Note: If you are installing an RDX internal USB tape drive, use the SATA-to-traditional power converter cable to serve as a bridge between the optical power cable and the power connector on the RDX tape drive. 7.
1 2 3 4 5 SATA optical drive power cable USB signal cable connector USB signal cable SATA optical drive power cable (SATA-to-traditional power converter cable also included but not pictured) SATA optical drive signal cable 8. Reinstall the fan cage assembly. Align the fan cage assembly over the fan cage assembly slot and with the connector on the system board. Lower the fan cage assembly into the chassis and press down firmly until the fan cage assembly is seated firmly in place.
Removing a 2.5-inch hot-swap hard disk drive Attention: To maintain proper system cooling, do not operate the server for more than 10 minutes without either a drive or a filler panel installed in each drive bay. To remove a 2.5-inch hot-swap hard disk drive, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37).
1 2 3 4 Release latch Drive tray handle (in open position) Drive tray Hard disk drive 7. If you are instructed to return the 2.5-inch hot-swap hard disk drive, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing a 2.5-inch hot-swap hard disk drive Before installing a 2.5-inch hot-swap hard disk drive, read the following information: v The 2.
1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 3. Remove the filler panel from the drive bay, if one is installed. 4. Orient the drive as shown in the illustration.
Removing a 3.5-inch hot-swap hard disk drive Attention: To maintain proper system cooling, do not operate the server for more than 10 minutes without either a drive or a filler panel installed in each drive bay. To remove a 3.5-inch hot-swap SAS or hot-swap SATA hard disk drive, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2. Unlock the side cover. 3. Open the bezel.
1 2 3 Hot-swap hard disk drive Drive tray Drive tray handle (in open position) 6. If you are instructed to return the 3.5-inch hot-swap hard disk drive, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing a 3.5-inch hot-swap hard disk drive Before installing a 3.5-inch hot-swap hard disk drive, read the following information: v The 3.
6. Check the hard disk drive status indicator to make sure that the hard disk drive is operating correctly. After you replace a failed hard disk drive, the green activity LED flashes as the disk spins up. The amber LED turns off after approximately 1 minute. If the new drive starts to rebuild, the amber LED flashes slowly, and the green activity LED remains lit during the rebuild process. If the amber LED remains lit, see the Hardware Maintenance Manual.
1 2 3 4 Filler panels Drive-bay EMC shield Tab Hard disk drive 6. Pull the loops of the drive assembly that is to be removed toward each other; then, pull the drive assembly out of the bay and set it aside. 7. If you are instructed to return the simple-swap hard disk drive, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing a simple-swap hard disk drive Attention: Simple-swap hard disk drives are not hot-swappable.
1 2 3 4 Filler panels Drive-bay EMC shield Tab Hard disk drive 3. Pull the loops of the drive assembly toward each other; then, carefully slide the drive assembly into the drive bay until it stops and release the loops. Note: Do not release the loops on the drive assembly until it is completely seated. 4. Close the drive bay EMC shield. 5. Close the bezel. 6. Lock the side cover. 7. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.
Table 4. IDs for the four-bay 3.5-inch hot-swap drive models (continued) Drive bay number ID Drive bay 5 1 Drive bay 6 2 Drive bay 7 3 Table 5. IDs for the eight-bay 2.
– The 2.5-inch hot-swap SAS and hot-swap SATA models come with the following cables to provide signal and power to the hot-swap SAS/SATA drives: - Two single signal cables (thick red and black) that connects to the signal cable connectors on the hard disk drive backplanes and the connectors on the SAS/SATA RAID adapter (see the ServeRAID adapters installation instructions in this document for more cabling information). - A split power cable (red/yellow/black).
CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. Statement 11: CAUTION: The following label indicates sharp edges, corners, or joints nearby.
1 2 Power supply Power-supply handle 5. Disconnect the cables from the power supply to the system board and all internal components. Be sure to make a note of the cable routing. Attention: Support the power supply while you remove the mounting screws. After the screws are removed, the power supply is loose and can damage other components in the server. 6.
1 2 Power supply retaining screws Power supply assembly 7. If you are instructed to return the power supply, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing a power supply To install a power supply, do the following: Note: Approximately 1 to 3 minutes after the server is connected to ac power, the power-control button becomes active. 1.
1 2 Power supply retaining screws Power supply assembly 2. While you support the power supply cage, install the three screws that secure the power supply to the chassis. 3. Connect the cables from the power supply to the system board and all internal components. 4. Rotate the power-supply-cage assembly back into the server. Press the power-supply-cage release tab and rotate the power-supply-cage assembly into the chassis. Chapter 5.
1 2 Power supply support bracket Power supply release tab 5. Install the side cover (see “Installing the side cover” on page 134). 6. Lock the side cover. 7. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing a hot-swap fan Attention: v Replace a hot-swap fan within 30 seconds of removal. v To ensure proper cooling and airflow, do not operate the server for more than 2 minutes with the side cover removed.
4. If you are instructed to return the hot-swap fan, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing a hot-swap fan Attention: v Replace a hot-swap fan within 30 seconds of removal. v To ensure proper cooling and airflow, do not operate the server for more than 2 minutes with the side cover removed. To install a hot-swap fan, do the following: 1.
3. Press down on the fan until it locks into place; then, close the fan handle to the locking position. 4. Install the side cover (see “Installing the side cover” on page 134). 5. Lock the side cover. Removing a memory module To remove a DIMM, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2. Turn off the server and all attached devices; then, disconnect all power cords and external cables. 3.
1 2 Power supply Power-supply handle 6. Remove the air baffle (see “Removing the air baffle” on page 44). 7. Locate the DIMM connector that contains the DIMM that is to be replaced. Note: Do not insert memory DIMMs into connectors marked as reserved. These DIMM slots are not supported in this model. Chapter 5.
88 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
1 2 3 4 5 6 7 8 DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM 1 (reserved) 2 3 4 (reserved) 5 6 7 8 9 10 11 12 13 14 15 16 DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM 9 (reserved) 10 11 12 (reserved) 13 14 15 16 . Attention: To avoid breaking the DIMM retaining clips or damaging the DIMM connectors, open and close the clips gently. 8. Carefully open the retaining clips on each end of the DIMM connector and remove the DIMM. 1 2 DIMM Retaining clip 9.
supported options for the server, see http://www.lenovo.com/thinkserver; then, select your country and navigate to the list of options for the server. – The specifications of a DDR3 DIMM are on a label on the DIMM, in the following format.
v v v v Note: The amount of usable memory is reduced depending on the system configuration. A certain amount of memory must be reserved for system resources. To view the total amount of installed memory and the amount of configured memory, run the Setup Utility. For additional information, see “Using the Setup Utility” on page 138. A minimum of one DIMM must be installed for each microprocessor. For example, you must install a minimum of two DIMMs if the server has two microprocessors installed.
The following table lists the installation sequence for installing DIMMs in memory-mirroring mode. Table 9. Memory-mirroring mode DIMM population sequence DIMMs Number of installed microprocessors DIMM connector First pair of DIMMs 1 3, 6 Second pair of DIMMs 1 2, 5 Third pair of DIMMs 2 11, 14 Fourth pair of DIMMs 2 10, 13 Note: DIMM connectors 7, 8, 15, and 16 are not used in memory-mirroring mode and DIMM connectors 1, 4, 9, and 12 are not functional on this server.
1 2 Power supply Power-supply handle 4. Remove the air baffle (see “Removing the air baffle” on page 44). 5. Locate the DIMM connectors on the system board. Determine the connector in which you will install the DIMM. Install the DIMMs in the sequence indicated earlier in this section. Note: DIMM connectors 1, 4, 9, and 12 are not functional in this server. Do not install DIMMs in these connectors.
8. Turn the DIMM so that the DIMM keys align correctly with the connector. 1 2 DIMM Retaining clip 9. Insert the DIMM into the connector by aligning the edges of the DIMM with the slots at the ends of the DIMM connector. Firmly press the DIMM straight down into the connector by applying pressure on both ends of the DIMM simultaneously. The retaining clips snap into the locked position when the DIMM is firmly seated in the connector.
1 2 Power supply support bracket Power supply release tab 12. Install the side cover (see “Installing the side cover” on page 134). 13. Lock the side cover. 14. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Removing an adapter To remove an adapter, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2.
1 2 3 Rear adapter-retention bracket Adapter Front adapter-retention bracket 8. If the adapter is not being replaced, install an expansion-slot cover in the expansion-slot opening. 9. If you are instructed to return the adapter, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping.
for x4 and x8 adapters. These same rules apply to the other PCI slots also. Check the information that comes with your adapter for compatibility information.
Note: Do not allow the server to fall over. 4. Follow the cabling instructions that come with the adapter to set jumpers or switches, if there are any. Route the adapter cables before you install the adapter. 5. Rotate the rear adapter-retention bracket to the open (unlocked) position. 6. If you are installing a full-length adapter, press on the release lever on the right side of the front adapter-retention bracket to release the retaining tab on the left side of the bracket. 7.
1 2 3 Adapter Rear adapter retention bracket Front adapter retention bracket 8. Connect all required cables to the adapter. Route cables so that they do not block air flow from the fans. 9. Rotate the rear and front adapter-retention brackets to the closed position. 10. Close the bezel. Install the side cover (see “Installing the side cover” on page 134). Lock the side cover. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.
v The first microprocessor must always be installed in microprocessor socket 1. v When one microprocessor is installed, a heat sink filler is not required for microprocessor socket 2; however, the air baffle must be installed to provide proper system cooling. v Do not remove the first microprocessor from the system board when you install the second microprocessor. v When you install the second microprocessor, you must also install additional memory. See “Installing a memory module” on page 89.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM DIMM 9 (reserved) 10 11 12 (reserved) 13 14 15 16 8 7 6 5 4 (reserved) 3 15 16 17 18 19 20 21 22 23 24 25 26 27 28 DIMM 2 DIMM 1 (reserved) Battery PCI extender card connector Microprocessor 1 Microprocessor 2 Slot 6, PCI 32 bit/33 MHz Slot 5, PCI Express Gen2 x8 (x8) Slot 4, PCI Express Gen2 x8 (x4) Slot 3, PCI Express Gen2 x8 (x4) Slot 2, PCI Express
4. Remove the air baffle (see “Removing the air baffle” on page 44). 5. Remove the fan cage assembly (see “Removing the fan cage assembly” on page 46). 6. Install the VRM in the VRM connector: a. Turn the VRM so that the VRM keys align correctly with the slot connector. b. Firmly press the VRM straight down into the connector by applying pressure on both ends of the VRM simultaneously.
c. Rotate the microprocessor release latch on the microprocessor socket from the closed and locked position to the fully open position. Attention: v Do not touch the microprocessor contact; handle the microprocessor by the edges only. Contaminants on the microprocessor contacts, such as oil from your skin, can cause connection failures between the contacts and the socket. v Handle the microprocessor carefully. Dropping the microprocessor during installation or removal can damage the contacts.
1 2 Thermal grease Heat sink a. Make sure that the heat-sink release lever is in the open position. b. Remove the plastic protective cover from the bottom of the heat sink. c. If the new heat sink did not come with thermal grease, (Trained service technician only) apply thermal grease on the microprocessor before you install the heat sink (see the Hardware Maintenance Manual for information on applying thermal grease). d. Align the heat sink above the microprocessor with the thermal-grease side down.
e. Tilt the heat sink slightly to the side and slide the heat sink flange underneath the flange of the heat sink retainer bracket. f. Press down firmly on the heat sink until it is seated securely. g. Rotate the heat-sink lever to the closed position and hook it underneath the lock tab. 10. Reinstall the air baffle (see “Installing the air baffle” on page 132). 11. Rotate the power-supply cage assembly back into the server.
5. Disconnect any cables connected to the adapter. Attention: To avoid breaking the retaining clips or damaging the ServeRAID-BR10i adapter connector, open and close the clips gently. 6. Carefully open the retaining clip on each end of the ServeRAID-BR10i adapter connector and remove the adapter from the server. 7. If you are instructed to return the adapter, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping.
1 2 ServeRAID-BR10i controller PCI slot 1 8. Press the ServeRAID-BR10i adapter firmly into the connector on the system board. 9. Rotate the power-supply cage assembly out of the chassis. Lift up the power-supply cage handle and pull the power-supply cage assembly all the way up until the retainer latch locks the cage in place on the chassis. 1 2 Power supply Power-supply handle 10. Remove the air baffle (see “Removing the air baffle” on page 44). Chapter 5.
11. Remove the fan cage assembly (see “Removing the fan cage assembly” on page 46). 12. Connect the configuration signal cable. See “Power and signal cables for internal drives” on page 78 for information about cabling the power and signal cables. 13. Complete the cabling of the ServeRAID-BR10i SAS/SATA adapter. v For the eight drive-bay, 2.
slots on the bottom of the chassis underneath the fan cage assembly; then, connect it to the ServeRAID-BR10i SAS/SATA controller as shown in the following illustration: 1 2 3 4 Signal cable for drives 4-7 Adapter connector for drives 4-7 signal cable Signal cable for drives 0-3 Adapter connector for drives 0-3 signal cable Connect the single end of the power cable to the Hard disk drive backplane power connector on the system board and connect the split end of the power cable to the connectors on
1 2 Adapter connector Signal cable 14. Reinstall the front fan cage assembly. Align the front fan cage assembly over the fan cage assembly slot and with the connector on the system board. Lower the fan cage assembly into the chassis and press down firmly until the fan cage assembly is seated firmly in place. Make sure that no cables will be pinched. 15. Reinstall the air baffle (see “Installing the air baffle” on page 132). 16. Rotate the rear adapter-retention bracket to the closed (locked) position.
1 2 Power supply support bracket Power supply release tab If you have other options to install or remove, do so now. Otherwise, Go to “Completing the installation” on page 130. Removing an optional ServeRAID-MR10i SAS/SATA controller To remove a ServeRAID-MR10i SAS/SATA adapter, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables.
Installing the optional ServeRAID-MR10i SAS/SATA controller The optional ServeRAID-MR10i SAS/SATA controller can be installed only in its dedicated connector, PCI slot 1, on the system board. The ServeRAID-MR10i adapter is supported on hot-swap server models only. The ServeRAID-MR10i SAS/SATA adapter enables integrated RAID levels 0, 1, 5, 6, 10, 50, and 60 support capability on hot-swap hard disk drives. For configuration information, see the documentation on the ServeRAID CD that comes with the adapter.
1 2 3 4 ServeRAID adapter Battery carrier Battery Connector for battery carrier b. Press the battery carrier into the connector on the ServeRAID adapter until it is firmly connected. c. Secure the battery carrier to the ServeRAID adapter with the screws that came with the battery pack. 9. Turn the ServeRAID-MR10i adapter so that the ServeRAID-MR10i adapter keys align correctly with the connector. Attention: Incomplete insertion might cause damage to the system board or the ServeRAID-MR10i adapter.
1 2 ServeRAID-MR10i controller PCI slot 1 10. Press the ServeRAID-MR10i adapter firmly into the connector on the system board. 11. Rotate the power-supply cage assembly out of the chassis. Lift up the power-supply cage handle and pull the power-supply cage assembly all the way up until the retainer latch locks the cage in place on the chassis. 1 2 Power supply Power-supply handle 12. Remove the air baffle (see “Removing the air baffle” on page 44). 13.
1 2 Adapter connector for drives 0-3 signal cable Signal cable for drives 0-3 The following illustration shows the connectors on the controller to which you connect the signal cables from the drive backplanes.
1 2 3 4 Signal cables for drives 4-7 Adapter connector for drives 4-7 signal cable Signal cable for drives 0-3 Adapter connector for drives 0-3 signal cable Connect the single end of the power cable to the Hard disk drive backplane power connector on the system board and connect the split end of the power cable to the connectors on the backplane as shown in the illustration. 1 2 3 Power connector Power cable Backplane power connectors v For the four drive-bay, 3.
1 2 Adapter connector Signal cable 16. Reinstall the front fan cage assembly. Align the front fan cage assembly over the fan cage assembly slot and with the connector on the system board. Lower the fan cage assembly into the chassis and press down firmly until the fan cage assembly is seated firmly in place. Make sure that no cables will be pinched. 17. Reinstall the air baffle (see “Installing the air baffle” on page 132). 18. Rotate the power-supply cage assembly back into the server.
1 2 Power supply support bracket Power supply release tab 19. If you have other options to install or remove, do so now. 20. Replace the side cover (see “Installing the side cover” on page 134). Go to “Completing the installation” on page 130. If you have other options to install or remove, do so now. Otherwise, go to “Completing the installation” on page 130. Removing an optional ServeRAID-MR10is VAULT SAS/SATA controller To remove a ServeRAID-MR10is SAS/SATA adapter, do the following: 1.
2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. Attention: To avoid breaking the retaining clips or damaging the ServeRAID-MR10is SAS/SATA adapter connector, open and close the clips gently. 3. Remove the side cover (see “Removing the side cover” on page 43). 4. Carefully position the server on its side so that it is lying flat and facing up. Note: Do not allow the server to fall over. 5.
c. Secure the battery carrier to the ServeRAID adapter with the screws that came with the battery pack. 10. Turn the ServeRAID-MR10is adapter so that the ServeRAID-MR10is adapter keys align correctly with the connector on the system board. Attention: Incomplete insertion might cause damage to the system board or the ServeRAID-MR10is adapter. 1 2 ServeRAID-MR10is connector PCI slot 1 11. Press the ServeRAID-MR10is adapter firmly into the connector on the system board. 12.
1 2 Power supply Power-supply handle 13. Remove the air baffle (see “Removing the air baffle” on page 44). 14. Remove the front fan cage assembly (see “Removing the fan cage assembly” on page 46). 15. Connect one end of the black configuration signal cable to the backplane and connect the other end to the hard disk drive backplane configuration signal cable connector on the system board. 16. Complete the cabling of the ServeRAID-MR10is SAS/SATA adapter. v For the eight drive-bay, 2.
1 2 Adapter connector for drives 0-3 signal cable Signal cable for drives 0-3 The following illustration shows the connectors on the controller to which you connect the signal cables from the drive backplanes.
1 2 3 4 Signal cable for drives 4-7 Adapter connector for drives 4-7 signal cable Signal cable for drives 0-3 Adapter connector for drives 0-3 signal cable Connect the single end of the power cable to the Hard disk drive backplane power connector on the system board and connect the split end of the power cable to the connectors on the backplane as shown in the following illustration. 1 2 3 Power connector Power cable Backplane power connectors v For the four drive-bay, 3.
1 2 Adapter connector Signal cable 17. Reinstall the front fan cage assembly. Align the front fan cage assembly over the fan cage assembly slot and with the connector on the system board. Lower the fan cage assembly into the chassis and press down firmly until the fan cage assembly is seated firmly in place. Make sure that no cables will be pinched. 18. Reinstall the air baffle (see “Installing the air baffle” on page 132). 19. Rotate the rear adapter-retention bracket to the closed (locked) position.
1 2 Power supply support bracket Power supply release tab 21. If you have other options to install or remove, do so now. 22. Replace the side cover (see “Installing the side cover” on page 134). Go to “Completing the installation” on page 130. Removing the virtual media key To remove the virtual media key, do the following: 1. Read the safety information (see “Safety” on page vii and “Installation guidelines” on page 37). 2.
Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model.
Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. Do not insert a memory DIMM in this connector. This DIMM slot is not supported in this model. 1 2 3 4 5 9. 10. 11. 12.
5. Rotate the power-supply cage assembly out of the chassis. Lift up the power-supply cage handle and pull the power-supply cage assembly all the way up until the retainer latch locks the cage in place on the chassis. 1 2 Power supply Power-supply handle 6. Remove the air baffle (see “Removing the air baffle” on page 44). 7. Remove the fan cage assembly (see “Removing the fan cage assembly” on page 46). 8. Slide the drives in bay 1 and bay 2 forward slightly toward the front of the server.
9. Disconnect the control-panel assembly cable from the system board, noting the routing of the cable (see “System-board internal connectors” on page 28 for the location of the front panel connector). 10. Locate the control-panel assembly release latch. 11. Press down the release latch of the control-panel assembly and pull the assembly toward the rear of the server. After you pull the assembly out approximately halfway, start turning it downward and pull it out of the chassis.
1 2 Power supply support bracket Power supply release tab 8. Close the bezel. 9. Install the side cover (see “Installing the side cover” on page 134). 10. Lock the side cover. 11. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Completing the installation To complete the installation, you must install the bezel, install the side cover, and connect all the cables and, for certain options, run the Setup Utility.
1 2 3 Bezel Hinge assembly Retention tabs 2. Push the hinges into the holes on the chassis until they snap into place. 3. If however, the bezel was removed by detaching the sliding hinge mount from the hinge assembly (using the breakaway method as the bezel was designed to do), do the following to reattach the bezel: a. Press in on the rear of the sliding hinge mount until it extends beyond the edge of the bezel and hold it in place. Chapter 5.
1 2 3 Sliding hinge mount Hinge pin Hinge assembly b. Align the sliding hinge mount with the hinge pin on the hinge assembly on the chassis. c. Press the sliding hinge mount against the hinge pin until the sliding hinge mount snaps onto the hinge pin. 4. Close the bezel. Note: When you lock the server side cover, it locks both the cover and the bezel. Installing the air baffle To replace the air baffle, do the following: 1.
1 2 Air baffle pinch tab Air baffle 2. Lower the air baffle into the server until the air baffle is seated firmly. 3. Press the power supply release tab and rotate the power supply back into the server. 1 2 Power supply support bracket Power supply release tab 4. Install the side cover (see “Installing the side cover” on page 134). Chapter 5.
5. Lock the side cover. 6. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. Installing the side cover If you removed the side cover, reinstall it. Attention: For proper cooling and airflow, replace the side cover before turning on the server. Operating the server for extended periods of time (more than 30 minutes) with the side cover removed might damage server components.
If the server cables and connector panel have color-coded connections, match the color of the cable end with the color of the connector. For example, match a blue cable end with a blue panel connector, a red cable end with a red connector, and so on. The following illustration shows the input/output (I/O) connectors on the rear of the server.
Some options have device drivers that you must install. For information about installing device drivers, see the documentation that comes with each option. If the server has a ServeRAID adapter and you have installed or removed a hard disk drive, see the ServeRAID documentation for information about reconfiguring the disk arrays. Connecting external devices If you install a supported optional adapter, you can attach external devices to the server. To attach an external device, do the following: 1.
Chapter 6. Configuring the server The following configuration programs and utilities come with the server: v Setup Utility The UEFI (formerly BIOS) Setup Utility program is part of the basic input/output system firmware. Use it to change the startup-device sequence, set the date and time, and set passwords. For information about using this program, see “Using the Setup Utility” on page 138. v Boot Manager program The Boot Manager program is part of the server firmware.
v Advanced Settings Utility (ASU) program Use this program as an alternative to the Setup Utility for modifying UEFI settings and IMM settings. Use the ASU program online or out of band to modify UEFI settings from the command line without the need to restart the server to access the Setup Utility. For more information about using this program, see “Advanced Settings Utility program” on page 159.
Select this choice to view the system-board identifier, the revision level or issue date of the firmware, the integrated management module and diagnostics code, and the version and date. This choice is on the full Setup Utility menu only. v System Settings Select this choice to view or change the server component settings. – Processors Select this choice to view or change the processor settings. – Memory Select this choice to view or change the memory settings.
specify whether to use the static IP address or have DHCP assign the IMM IP address; save the network changes. - Reset IMM to Defaults Select this choice to view or reset IMM to the default settings. - Reset IMM Select this choice to reset IMM. – System Security Select this choice to view or configure Trusted Platform Module (TPM) support. – Adapters and UEFI Drivers Select this choice to view information about the UEFI 1.10 and UEFI 2.0 compliant adapters and drivers installed in the server.
v User Security Select this choice to set, change, or clear passwords. See “Passwords” for more information. This choice is on the full and limited Setup Utility menu. – Set Power-on Password Select this choice to set or change a power-on password. See “Power-on password” on page 142 for more information. – Clear Power-on Password Select this choice to clear a power-on password. See “Power-on password” on page 142 for more information.
password has access to only the limited Setup Utility menu; the user can set, change, and delete the power-on password, if the system administrator has given the user that authority. Power-on password If a power-on password is set, when you turn on the server, the system startup will not be completed until you type the power-on password. You can use any combination of up to seven characters (A - Z, a - z, and 0 - 9) for the password.
Table 11. RAID configuration utilities (continued) RAID configuration utility MegaRAID BIOS Configuration Utility (WebBIOS) Description Location Where to find more information For: In system firmware. To access: “Using the WebBIOS utility” on page 145 v ServeRAID-MR10i controller v ServeRAID-MR10is controller v ServeRAID-MR10m controller LSI Logic MPT Setup For: Utility v ServeRAID-BR10i controller v Use UEFI Setup Utility. v Press Ctrl + H at the WebBIOS prompt during startup. In system firmware.
v Hard disk drive capacities affect how you create arrays. The drives in an array can have different capacities, but the RAID controller treats them as if they all have the capacity of the smallest hard disk drive. v If you use an integrated SAS/SATA controller with RAID capabilities to configure a RAID 1 (mirrored) array after you have installed the operating system, you will lose access to any data or applications that were previously stored on the secondary drive of the mirrored pair.
3. Select the type of array that you want to create. 4. In the RAID Disk column, use the Spacebar or Minus (-) key to select [Yes] (select) or [No] (deselect) to select or deselect a drive from a RAID disk. 5. Continue to select drives, using the Spacebar or Minus (-) key, until you have selected all the drives for your array. 6. Press C to create the disk array. 7. Select Save changes then exit this menu to create the array. 8. Exit the Setup Utility.
Physical View or Logical View Select this to toggle between the Physical View and Logical View. Events From this view, you can display the system events in the Event Information page. Exit Select this to exit the WebBIOS utility and continue with the system boot. Creating a storage configuration using the Configuration Wizard Do the following to start create a storage configuration: 1. Click Configuration Wizard to start the wizard. 2.
menu and click Change. The Operations panel lists operations that can be performed on the virtual disk. Select the operation and click Go. Then choose from the following operations: v Select Del to delete this virtual disk. v Select Locate and the LEDs flash on the physical drives used by this virtual disk. v Select Fast or Slow to initialize this virtual disk. Attention: Before you run an initialization, back up any data on the virtual disk that you want to save.
Configuring RAID The RAID configuration feature that is part of the EasyStartup program enables you to view and change RAID settings for supported RAID controllers. Through this feature, you have the ability to select one RAID level for each installed controller, and the program automatically uses the discs currently attached to the controller to support that RAID level. This method satisfies most users' needs.
You will then see one or more reminders about configuring storage devices, and then you will be presented with the Lenovo License Agreement. Read the license agreement carefully. You must agree with terms in order to continue.
v Install applications: This task enables you to run custom commands or scripts at the end of the installation process. It also facilitates the installation of DVD-burning software and EasyManage software products. v Install Windows components: This task enables you to install optional Windows components such as IIS, ASP.NET, and SNMP. v Confirm settings: This task enables you to review all of the information you provided.
Enabling the Broadcom Gigabit Ethernet Utility program The Broadcom Gigabit Ethernet Utility program is part of the server firmware. You can use it to configure the network as a startable device, and you can customize where the network startup option appears in the startup sequence. To enable the Broadcom Gigabit Ethernet Utility program, do the following: 1. From the Setup Utility main menu, select Devices and I/O Ports and press Enter. 2. Select Enable/Disable onboard device(s) and press Enter. 3.
3. From Family list, select ThinkServer TD200, and click Continue. 4. Click Downloads and drivers to download firmware updates. Download the latest firmware for the server; then, install the firmware, using the instructions that are included with the downloaded files. When you replace a device in the server, you might have to either update the server with the latest version of the firmware that is stored in memory on the device or restore the pre-existing firmware from a diskette or CD image.
To download the server firmware update package from the World Wide Web, do the following: Note: Changes are made periodically to the Lenovo Web site. The actual procedure might vary slightly from what is described in this document. 1. Go to: http://www.lenovo.com/support. 2. Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. 3. From Family list, select ThinkServer TD200, and click Continue. 4.
6. Reinstall the server cover (see “Installing the side cover” on page 134); then, reconnect all power cords. 7. Restart the server. The power-on self-test (POST) starts. 8. Boot the server to an operating system that is supported by the firmware update package that you downloaded. 9. Perform the firmware update by following the instructions that are in the firmware update package readme file. 10. Copy the downloaded firmware update package into a directory. 11.
2. Remove any devices that you added recently and restart the server. 3. If the problem remains, go to the Setup utility and select Load Default Settings, and then click Save to restore the server factory settings. Using the integrated management module The integrated management module (IMM) is a second generation of the functions that were formerly provided by the baseboard management controller hardware.
v Boot sequence manipulation. The IMM also provides the following remote server management capabilities: v Command-line interface (IPMI Shell) The command-line interface provides direct access to server management functions through the IPMI 2.0 protocol. Use the command-line interface to issue commands to control the server power, view system information, and identify the server. You can also save one or more commands as a text file and run the file as a script.
1. Install the virtual media key into the dedicated slot on the system board (see “System-board option connectors” on page 30). 2. Turn on the server. Note: Approximately 1 to 3 minutes after the server is connected to ac power, the power-control button becomes active. Obtaining the IP address for the IMM To access the Web interface, you need the IP address for the IMM. You can obtain the IMM IP address through the Setup Utility. The server comes with a default IP address for the IMM of 192.168.70.125.
Diagnostics programs and messages The diagnostics programs are the primary method of testing the major components of the server. As you run the diagnostics programs, text messages are displayed on the screen and are saved in the test log. A diagnostics text message indicates that a problem has been detected and provides the action you should take as a result of the text message. Make sure that the server has the latest version of the diagnostics programs.
Note: The DSA Preboot diagnostics program might appear to be unresponsive for an unusual length of time when you start the program. This is normal operation while the program loads. 4. Optionally, select Quit to DSA to exit from the stand-alone memory diagnostics program. Note: After you exit from the stand-alone memory diagnostics environment, you must restart the server to access the stand-alone memory diagnostics environment again. 5.
Installing EasyManage software You can install the ThinkServer™ EasyManage Core Server program from the EasyManage CD or you can download and install the program from http://www.lenovo.com/support. After one instance of the EasyManage Core Server has been installed, you can use the EasyManage Agent installer to install the agent on other servers and clients on the network.
Note: This specific version is required. 6. Use Windows Update to install all available critical updates. 7. Launch the EasyManage installation. 8. After EasyManage is installed, enable Security and Patch Manager to obtain the LANDesk 8.8 Software Updates. In the console application, click Help -> LANDesk -> Security Updates for a guide to configuring Security and Patch Manager. 9.
v v v v v Static Content ASP.NET ASP CGI Server Side Includes v Windows Authentication v IIS 6 Metabase Compatibility Note: When you select ASP.Net or ASP, a dialog box displays the additional role services required. Click Add Required Role Services. 6. Click Install. Note: If IIS is already installed and certain Role Services are still required, expand Roles in the tree view on the left in Server Manager and click Web Server (IIS), then click Add Role Services.
Chapter 7. Troubleshooting This chapter describes the diagnostic tools that are available to help you solve problems that might occur in the server. If you cannot locate and correct the problem using the information in this chapter, see the Hardware Maintenance Manual for more information. Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms. If you cannot find the problem in these tables, see the Hardware Maintenance Manual.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action A CD or DVD is not working correctly. 1. Clean the CD or DVD. 2.
General problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Intermittent problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Memory problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action The amount of system memory 1.
Microprocessor problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action A microprocessor LED is lit 1.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action The screen is blank. 1. Make sure that: v The server is turned on.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action Wrong characters appear on the 1.
Power problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action The power-control button does 1.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Software problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Symptom Action You suspect a software problem. 1.
clear the CMOS memory; see “System-board switches and jumpers” on page 31. If you suspect that the server firmware is damaged, see “Recovering the server firmware” on page 152. Check the LEDs on all the power supplies. If the LEDs indicate that the power supplies are working correctly, do the following: 1. Turn off the server. 2. Make sure that the server is cabled correctly. 3. Remove or disconnect the following devices, one at a time, until you find the failure.
1. Make sure that external SCSI devices are turned on before you turn on the server. 2. Make sure that the cables for all external SCSI devices are connected correctly. 3. If an external SCSI device is attached, make sure that the external SCSI termination is set to automatic. 4. Make sure that the last device in each SCSI chain is terminated correctly. 5. Make sure that the SCSI devices are configured correctly. Solving power problems Power problems can be difficult to solve.
– The Ethernet transmit/receive activity LED is lit when the Ethernet controller sends or receives data over the Ethernet network. If the Ethernet transmit/receive activity light is off, make sure that the hub and network are operating and that the correct device drivers are installed. v Check the LAN activity LED on the rear of the server. The LAN activity LED is lit when data is active on the Ethernet network.
v Integrated management module (IMM) event log: This log contains a superset of IMM, POST, and systems-management interrupt (SMI) information that is in the system-event log. You can only access the event log through the IMM Web interface. v DSA log: This log is generated by the Dynamic System Analysis (DSA) Preboot program, and it contains merged contents of the system-event log and the IMM system-event log.
Table 12. Methods for viewing event logs Condition Action The server is not hung and is connected to a Run Portable or Installable DSA to view the network. event log or create an output file that you can send to Lenovo service and support. Alternatively, you can use IPMItool to view the system-event log. The server is not hung and is not connected to a network. Use IPMItool locally to view the system-event log.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error code Description Action 0010002 Microprocessor not supported. 1.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error code Description Action 0011004 Microprocessor failed BIST. 1.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error code Description Action 005100A No usable memory detected. 1.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error code Description Action 0068002 CMOS battery cleared. 1. Reseat the battery. 2.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Appendix A. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This section contains information about where to go for additional information about Lenovo and Lenovo products, what to do if you experience a problem with your system, and whom to call for service, if it is necessary.
Calling for service During the warranty period, you can get help and information by telephone through the Customer Support Center. These services are available during the warranty period: v Problem determination - Trained personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the problem. v Hardware repair - If the problem is caused by hardware under warranty, trained service personnel are available to provide the applicable level of service.
Service methods and procedures vary by country, and some services might not be available in all countries. International Warranty Service is delivered through the method of service (such as depot, carry-in, or on-site service) that is provided in the servicing country. Service centers in certain countries might not be able to service all models of a particular machine type. In some countries, fees and restrictions might apply at the time of service.
190 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Maximum memory might require replacement of the standard memory with an optional memory module. Lenovo makes no representations or warranties with respect to non-Lenovo products. Support (if any) for the non-Lenovo products is provided by the third party, not Lenovo. Some software might differ from its retail version (if available) and might not include user manuals or all program functionality.
Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenne et à la Norvège. L’etiquette du système respecte la Directive européenne 2002/96/EC en matière de Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les dispositions de retour et de recyclage applicables aux systèmes utilisés à travers l’Union européenne. Conformément à la directive, ladite étiquette précise que le produit sur lequel elle est apposée ne doit pas être jeté mais être récupéré en fin de vie.
Recycling statements for Japan Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo.com/lenovo/environment or contact your local waste disposal facility. For Taiwan: Please recycle batteries.
For the European Union: Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union.
Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der Bildschirmarbeitsverordnung geeignet. Electronic emission notices Federal Communications Commission (FCC) statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-Lenovo option cards This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment.
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A. Nach der EN 55022: “Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.
Korea Class A warning statement 200 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Index A ABR, automatic boot failure recovery 154 acoustical noise emissions 9, 11 adapter hot-plug devices 106 installing 97 hot-plug 106 removing 95 requirements 96 scanning order 97 ServeRAID-BR10i 106 ServeRAID-MR10i installing 112 ServeRAID-MR10is installing 118 specifications 9 administrator password 142 administrator password, clear 141 administrator password, set 141 Advanced Settings Utility program overview 159 assertion event, system-event log 176 assistance, getting 187 attention notices 2 automa
D danger statements 2 DASD LED 22 data rate, Ethernet 151 deassertion event, system-event log 176 diagnostics program 8 DIMM installation sequence for memory mirroring 92 DIMMs installing 89 order of installation for independent mode 91 removing 86 diskette drive problems 164 display problems 168 documentation DVD 3 drive cables 78 removable-media 62 drive, installing 2.
firmware updates 1 firmware, server starting the backup 152 firmware, server, recovering 152 firmware, updating 151 formatting hard disk drive 144 front USB connector assembly installing 51 removing 49 front, controls and indicators 15 G getting help 187 gloss statement (Germany) 196 guidelines, system reliability 38 H handling static-sensitive devices 39 hard disk drive activity LED 17, 18 formatting 144 LED 22 problems 165 status LED 18 hard disk drives hot-swap SAS or SATA, installing 74 hot-swap SAS o
LEDs DVD drive activity 18 EasyLED; diagnostics 25 Ethernet link status 27 Ethernet transmit/receive activity 27 hard disk drive activity 17 hot-swap hard disk drive activity 18 hot-swap hard disk drive status 18 power-on 17 system board 33 system-error 17 LEDs and controls on the front of the server 15 LEDs, EasyLED CNFG 23 CPU 24 DASD 22 fan 21 LOG 21 MEM 23 NMI 22 PCI bus 21 power supply 22 SP 25 System Board 21 TEMP 21 VRM 24 LEDs, on the rear of the server 26 locking and unlocking, the bezel media door
password, power-on clear 141 set 141 passwords 141 PCI bus LED 21 PCI extender card one-slot 34 two-slot 34 pointing-device problems 166 ports Ethernet 27 serial 27 Universal Serial Bus (USB) 18, 27 video 27 POST 176 error codes 178 event log 177 POST event log 176 power and signal cables connecting to internal drives 78 power control-button 17 power on and working inside the server power problems 171, 175 power supply LED 22 non-hot-swap installing 82 specifications 10 power supply cage assembly non-hot-sw
safety information (continued) Statement 3 xi Statement 4 xii Statement 5 xii Statement 8 xiii system reliability considerations 38 when the server is on 38 SAS or SATA hot-swap drives installing 74 removing 73 SATA backplane activity LEDs for hot-swap drives 18 SATA simple-swap drives installing 76 removing 75 scanning order for adapters 97 SCSI (SAS) error messages 174 Serial Advanced Technology Attachment (SATA) status LEDs for hot-swap drives 18 Serial Attached SCSI (SAS) backplane description 77 IDs fo
weight 9, 10 working inside the server with the power on 38 TÜV gloss statement 196 two-slot PCI extender card 34 U UEFI boot recovery jumper 153 UEFI update failure recovery 152 undetermined problems 173 United States electronic emission Class A notice United States FCC Class A notice 197 Universal Serial Bus (USB) connectors front 18 rear 27 Universal Serial Bus (USB) problems 173 updating firmware 151 USB, front connector assembly installing 51 removing 49 user password 142 using EasyStartup 147 LSI Co
208 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide
Part Number: 44W2344 Printed in USA (1P) P/N: 44W2344
