ThinkPad T500 and W500 Hardware Maintenance Manual
ThinkPad T500 and W500 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 205. Forth Edition (January 2009) © Copyright Lenovo 2008, 2009. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices: multilingual translations . . . . . 7 Laser compliance statement . . . . . . . . . 14 Important service information . . . . .
Miscellaneous parts . AC adapters . . . . Power cords . . . . Recovery discs . . . Common service tools iv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 191 192 193 203 ThinkPad T500 and W500 Hardware Maintenance Manual Notices . . . . . . . . . . . . . . 205 Trademarks . . . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad T500 MT 2055, 2056, 2081, 2082, 2083, 2087, 2088, 2089, 2241, 2242, 2243, 2246, 2247, and 2261 ThinkPad W500 MT 4058, 4061, 4062, 4063, 4064, and 4065 Use this manual along with the advanced diagnostic tests to troubleshoot problems.
vi ThinkPad T500 and W500 Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
16 ThinkPad T500 and W500 Hardware Maintenance Manual
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 18 – “Important notice for replacing a system board” on page 18 – “How to use error message” on page 18 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19 – “Product definition” on page 19 – “FRU identification for CTO, CMV, and GAV products” on page 19 v “Important information about replacing RoHS compliant FRUs” on p
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
warranty.vm&sitestyle=lenovo Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
22 ThinkPad T500 and W500 Hardware Maintenance Manual
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-Doctor for Windows” on page 28 – “PC-Doctor for Rescue and Recovery” on page 28 v “Power system checkout” on page 29 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “ThinkPad T500 and W500” on page 47. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.
2. The main panel of PC-Doctor appears. 3. Select Diagnostics with the arrow keys, and press Enter. A pull-down menu appears. (Its exact form depends on the model.) Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu.
To cancel the test, press Esc. Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect.
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 63). 4. Remove the backup battery (see “1100 Backup battery” on page 79). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
32 ThinkPad T500 and W500 Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on page 37 v “Symptom-to-FRU index” on page 39 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Passwords As many as three passwords may be needed for any ThinkPad computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 63. 3. Remove the backup battery. For how to remove the backup battery, see “1100 Backup battery” on page 79. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5.
3. 4. 5. 6. 7. 8. 9. 36 Note: To check whether the ThinkPad computer supports the Passphrase function, enter the BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. Select Security, using the cursor directional keys to move down the menu. Select Password. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens. Select Master HDP.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press the ThinkVantage® button and use the ThinkVantage Productivity Center. To end screen blank mode and resume normal operation, press any key.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 43 v “Beep symptoms” on page 44 v “No-beep symptoms” on page 44 v “LCD-related symptoms” on page 45 v “Intermittent problems” on page 46 v “Undetermined problems” on page 46 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 40 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication.
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 39. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is as follows: Table 5.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
ThinkPad T500 and W500 This chapter presents following product-specific service references and product-specific parts information. v “Specifications” v “Status indicators” on page 50 v “FRU tests” on page 53 v “Fn key combinations” on page 55 v “FRU replacement notices” on page 58 v “Removing and replacing a FRU” on page 62 v “Locations” on page 119 v “Parts list” on page 121 Specifications The following table lists the specifications of the ThinkPad T500 and W500 : Table 7.
Table 7. Specifications (continued) Feature Description Display v 15.4-inch, 16M colors, WXGA (1280 × 800 resolution) TFT color LCD v 15.4-inch, 16M colors, WXGA (1280 × 800 resolution) TFT color LCD, LED backlight v 15.4-inch, 16M colors, WSXGA+ (1680 × 1050 resolution) TFT color LCD v 15.
Table 7. Specifications (continued) Feature Description Internal modem v 56.
Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 6 7 8 9 10 11 10 50 ThinkPad T500 and W500 Hardware Maintenance Manual 9 8
Table 8. Status indicators Indicator Meaning 1 Wireless status Green: The wireless feature (802.11 standard or 802.11n) is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 2 Wireless PAN status Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. R 3 Wireless WAN status Green: The wireless WAN is on, and the radio link is ready for use. Blinking green: Data is being transmitted.
Table 8. Status indicators (continued) 52 Indicator Meaning 11 Green: A Serial Ultrabay Slim device is installed and in use. Blinking green: A Serial Ultrabay Slim device is in the process of being detached. Turn off: A Serial Ultrabay Slim device is ready to be attached or detached. Note: If you are using Windows 2000, the Serial Ultrabay Slim status indicator does not blink while a Serial Ultrabay Slim device is being detached.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the ThinkPad Advanced Dock, the ThinkPad Advanced Mini Dock or the ThinkPad Essential Port Replicator is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
Table 9. FRU tests (continued) FRU Applicable test Diskette drive 1. Diagnostics --> Diskette Drives 2. Interactive Tests --> Diskette Optical drive 1. Diagnostics --> Other Devices--> Optical Drive 2. Interactive Tests --> Optical Drive Test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Advanced Memory Tests. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. Fan 1.
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock your computer. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears. Notes: 1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer. 2.
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Notes: 1.
Table 10. Fn key combinations (continued) Key combination Description Fn+Spacebar Enable the FullScreen Magnifier function. Fn+PrtSc Has the same function as the SysRq key. Fn+ScrLk Enable or disable the numeric keypad. Fn+Pause Has the same function as the Break key. Fn+cursor keys These key combinations work with Windows Windows Media Player.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 61 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application. To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 58. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 11. Removal steps of battery pack Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 . 1 2 3 When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1020 Serial Ultrabay Slim device Note: Serial Ultrabay Slim does not accept any of the following devices: v Ultrabay Plus™ devices v Ultrabay 2000™ devices v Ultrabay Enhanced devices v Ultrabay Slim devices v Ultrabay devices Table 12. Removal steps of Serial Ultrabay Slim device When you release the switch in step 1 , the lever pops out. In step 2 , pull the lever a little to release the device from the bay.
1030 Hard disk drive (HDD) cover, HDD and HDD rubber rails or solid state drive (SSD) and storage converter For access, remove this FRU: v “1010 Battery pack” on page 63 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 13. Removal steps of HDD cover, HDD and HDD rubber rails or SSD and storage converter (continued) HDD and HDD rubber rails: 5 5 When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly.
1040 Palm rest or palm rest with fingerprint reader For access, remove this FRU in order: v “1010 Battery pack” on page 63 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader has any defects, you can replace it by the procedures given in this section, which are the same for a palm rest with or without a fingerprint reader. Table 14.
Table 14. Removal steps of palm rest (continued) 3 When installing: When you attach the palm rest, do as follows: Table 15. Installation of the palm rest 1. Attach the fingerprint reader connector firmly to the system board. 2. Attach the palm rest so that the two projections of the palm rest ( a ) firmly fit into the guide holes of the keyboard bezel as shown in this figure.
Table 15. Installation of the palm rest (continued) 3. Push the front side of the palm rest until it clicks into place. 4. Close the LCD cover and turn the computer over. Then fasten the four screws to secure the palm rest.
1050 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 Table 16. Removal steps of DIMM Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a : lower slot), but not in SLOT-1 ( b : upper slot). 1 b 2 a 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1060 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 Table 17. Removal steps of keyboard 1 Step 1 Icon Screw (quantity) Color Torque M2 × 14 mm, wafer-head, nylon-coated (1) Black 0.189 Nm (1.85 kgfcm) Lift the keyboard a little in the direction shown by arrow 2 , and then detach the connector 3 .
Table 17. Removal steps of keyboard (continued) When installing: Make sure that the keyboard edges a are under the frame as shown in this figure.
1070 Modem daughter card (MDC-3.0) For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 Table 18. Removal steps of MDC-3.0 1 1 2 1 3 Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (3) Silver 0.189 Nm (1.85 kgfcm) In step 3 , remove the card by pulling the tab with your fingers in the direction shown by the arrow.
Table 18. Removal steps of MDC-3.0 (continued) Turn the card over 4 , and detach the modem connector 5 . 4 5 When installing: Make sure that the modem connector and the connector on the underside of the card are attached firmly.
1080 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 Table 19. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 19. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN, and the black cable into the jack labeled AUX on the card. If the computer you are servicing has three cables, put the white cable in the cable holder and place it under the card.
1090 Intel Turbo Memory Minicard or Wireless USB adapter For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 Table 20. Removal steps of Intel Turbo Memory Minicard or Wireless USB adapter Note: Step 1 is only for the models with the Wireless USB adapter. For the models with the Intel Turbo Memory Minicard, skip step 1 .
Table 20. Removal steps of Intel Turbo Memory Minicard or Wireless USB adapter (continued) 2 3 Step Screw (quantity) 2 For Japan M2 × 3 mm, tamper proof (2) Color Torque Black 0.189 Nm (1.85 kgfcm) Silver 0.189 Nm (1.
1100 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 Table 21. Removal steps of backup battery 1 2 When installing: Make sure that the battery connector is attached firmly.
1110 SIM card slot For access, remove these FRUs, in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 Note: If the SIM card has been inserted in the slot, remove it before you start the servicing. After you finish the servicing, make sure that you insert the card back into the slot firmly. Table 22. Removal steps of SIM card slot 1 2 Step Screw (quantity) Color 1 M2 × 3.
1120 Keyboard bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 Table 23. Removal steps of keyboard bezel 1 1 Step Screw (quantity) Color Torque 1 M2 × 14 mm, wafer-head, nylon-coated (2) Black 0.189 Nm (1.
Table 23. Removal steps of keyboard bezel (continued) 3 4 3 2 4 3 3 In step 2 , release the wireless antenna cables from the cable guide. Step Screw (quantity) Color Torque 3 M2 × 3 mm, small-head, nylon-coated (4) Silver 0.189 Nm (1.85 kgfcm) 4 M2 × 3.5 mm, wafer-head, nylon-coated (2) Black 0.189 Nm (1.85 kgfcm) In step 5 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 6 .
1130 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 81 Table 24. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 24. Removal steps of PCI Express Mini Card for wireless WAN (continued) 3 Table 25. Installation of the PCI Express Mini Card for wireless WAN Cable routing: When you install the card, route the antenna cables as shown in this figure. If the computer you are servicing is the wireless WAN-ready model, put the cables in the cable holders and secure them with tape as shown in this figure.
1140 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 81 Table 26. Removal steps of speaker assembly The speaker cables are secured with tapes ( a ). 1 1 a 1 1 a Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (4) Silver 0.189 Nm (1.
Table 26. Removal steps of speaker assembly (continued) Cable routing: Make sure that the speaker connector is attached firmly, and the cables are routed as in this figure.
1150 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 81 v “1140 Speaker assembly” on page 85 Table 27. Removal steps of fan assembly 2 3 2 1 3 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (2) Silver 0.189 Nm (1.85 kgfcm) 2 M2 × 9.5 mm, wafer-head, nylon-coated (2) Black 0.189 Nm (1.
Table 27. Removal steps of fan assembly (continued) 5 5 4 4 Step Screw (quantity) Color 4 M2 × 9.5 mm, wafer-head, nylon-coated (2) Silver Torque 0.189 Nm (1.85 kgfcm) In step 5 , release the wireless antenna cables from the cable guide of the fan assembly.
Table 28. Installation of the fan assembly When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. In some modes, you need to peel the thin film off from the rubber b .
Table 28. Installation of the fan assembly (continued) v When attaching the fan assembly to the frame, take care not to damage the heat sink and the cable guides ( b ) of the fan assembly.
1160 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 81 v “1140 Speaker assembly” on page 85 v “1150 Fan assembly” on page 87 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Table 29.
1170 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1120 Keyboard bezel” on page 81 v “1130 PCI Express Mini Card for wireless WAN” on page 83 Table 30. Removal steps of LCD assembly 1 92 1 Step Screw (quantity) Color Torque 1 M2.5 × 6.5 mm, wafer-head, nylon-coated (2) Black 0.
Table 30. Removal steps of LCD assembly (continued) 3 2 3 Step Screw (quantity) Color Torque 3 M2.5 × 6.5 mm, wafer-head, nylon-coated (2) Black 0.
Table 30. Removal steps of LCD assembly (continued) 4 4 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 2. Make sure that the LCD connector is attached firmly.
1180 Base cover and USB sub card with cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1120 Keyboard bezel” on page 81 v “1130 PCI Express Mini Card for wireless WAN” on page 83 v “1170 LCD unit” on page 92 Table 31.
Table 31. Removal steps of base cover and USB sub card with cable (continued) 3 4 4 96 Step Screw (quantity) 3 M2 × 9.5 mm, wafer-head, nylon-coated (1) Black 0.189 Nm (1.85 kgfcm) 4 M2 × 14 mm, wafer-head, nylon-coated (2) 0.189 Nm (1.
Table 31. Removal steps of base cover and USB sub card with cable (continued) 6 6 6 5 Step Screw (quantity) Color Torque 5 M2 × 3 mm, small-head, nylon-coated (1) Silver 0.189 Nm (1.85 kgfcm) When installing: Make sure that the connectors are attached firmly.
Table 31. Removal steps of base cover and USB sub card with cable (continued) Attention: Before step 7 , be sure that the Serial Ultrabay Slim device eject lever has not popped out. It must be housed in its position as shown in the figure a . 7 8 a Remove the USB sub card with cable as shown in this figure. 1 1 2 98 Step Screw (quantity) 1 M2 × 3.5 mm, wafer-head, nylon-coated (2) Black ThinkPad T500 and W500 Hardware Maintenance Manual Color Torque 0.189 Nm (1.
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 1 Product label 1a Non-mercury label Note: If the computer you are servicing is an LED-backlight LCD model, you need to paste this label so that the notice for mercury on the product label is covered.
1190 Structure frame For access, remove these FRUs, in order: v “1010 Battery pack” on page 63 v “1020 Serial Ultrabay Slim device” on page 64 v “1030 Hard disk drive (HDD) cover, HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 65 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1070 Modem daughter card (MDC-3.
Table 32. Removal steps of structure frame (continued) Remove the AC power jack cable a . 3 a 2 When installing: Make sure the connector is attached firmly, and that the cable is routed as in the figure above. Remove the CPU support plate. 4 5 Step Screw (quantity) Color Torque 4 M2 × 5 mm, wafer-head, nylon-coated (1) Black 0.189 Nm (1.
Table 32. Removal steps of structure frame (continued) 7 6 6 6 8 6 a 9 9 Step Screw (quantity) Color 6 M2 × 3.5 mm, wafer-head, nylon-coated (4) Black 0.189 Nm (1.85 kgfcm) 7 M2 × 9.5 mm, wafer-head, nylon-coated (1) Black 0.189 Nm (1.85 kgfcm) 8 M2 × 3 mm, small-head, nylon-coated (1) 0.189 Nm (1.85 kgfcm) Silver Torque In step 9 , loosen the hex screws. When installing: When attaching the system board to the frame, adjust the placement with the small projection a .
1200 System board and ExpressCard slot assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
For access, remove these FRUs, in order: v “1010 Battery pack” on page 63 v “1020 Serial Ultrabay Slim device” on page 64 v “1030 Hard disk drive (HDD) cover, HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 65 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1050 DIMM” on page 70 v “1060 Keyboard” on page 71 v “1070 Modem daughter card (MDC-3.
Table 33. Removal steps of system board and ExpressCard slot assembly 1 1 Step Screw (quantity) Color 1 M2 × 2.7 mm, wafer-head, nylon-coated (2) Black Torque 0.189 Nm (1.85 kgfcm) Turn the system board over, and then disconnect the ExpressCard slot assembly a from the system board. a 2 When installing: Make sure that the connector of the Express Card slot assembly is attached to the system board firmly.
2010 LCD front bezel (LCD cover kit) For access, remove this FRU: v “1010 Battery pack” on page 63 Table 34. Removal steps of LCD front bezel 2 1 2 1 1 1 Step 106 Screw cap Screw (quantity) Color Torque 1 M2.5 × 6.5 mm, bind-head, nylon-coated (3) Black 0.392 Nm (4 kgfcm) 2 M2.5 × 6.5 mm, bind-head, nylon-coated (2) Black 0.
Table 34. Removal steps of LCD front bezel (continued) Close the LCD cover. Detach the LCD rear cover a little as shown in step 3 of this figure, and detach the rear edge of the LCD rear cover 4 .
2020 LCD rear cover (LCD cover kit) For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel (LCD cover kit)” on page 106 Table 35.
2030 Inverter card or LED control card For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel (LCD cover kit)” on page 106 Table 36. Removal steps of inverter card or LED control card 1 2 1 3 4 Step Screw (quantity) Color 1 M2 × 2.8 mm, wafer-head, nylon-coated (2) Silver Torque 0.189 Nm (1.
2040 Integrated camera For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel (LCD cover kit)” on page 106 Table 37. Removal steps of integrated camera 2 1 2 Step Screw (quantity) Color 1 M2 × 3.5 mm, wafer-head, nylon-coated (2) Black Torque 0.189 Nm (1.
2050 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel (LCD cover kit)” on page 106 Table 38. Removal steps of BDC-2.1 1 2 Step Screw (quantity) Color 1 M2 × 2.8 mm, wafer-head, nylon-coated (1) Silver Torque 0.189 Nm (1.85 kgfcm) When installing: Make sure that connector is attached firmly.
2060 Antenna assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 81 v “1130 PCI Express Mini Card for wireless WAN” on page 83 v “1170 LCD unit” on page 92 v “2010 LCD front bezel (LCD cover kit)” on page 106 v “2020 LCD rear cover (LCD cover kit)” on page 108 Table 39.
Table 39.
Table 39.
2070 LCD panel and LCD cable For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1120 Keyboard bezel” on page 81 v “1130 PCI Express Mini Card for wireless WAN” on page 83 v “1170 LCD unit” on page 92 v “2010 LCD front bezel (LCD cover kit)” on page 106 v “2020 LCD rear cover (LCD cover kit)” on page 108 v “2030 Inverter card or LE
Table 40. Removal steps of LCD panel and LCD cable (continued) 5 4 8 7 6 9 6 6 6 6 116 7 Step Screw (quantity) Color Torque 6 M2 × 2.8 mm, small-head, nylon-coated (5) Silver 0.189 Nm (1.
Table 40. Removal steps of LCD panel and LCD cable (continued) 8 b 9 When installing: Make sure that the LCD cable is attached firmly.
2080 Hinges and LCD magnesium frame For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Palm rest or palm rest with fingerprint reader” on page 67 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1120 Keyboard bezel” on page 81 v “1130 PCI Express Mini Card for wireless WAN” on page 83 v “1170 LCD unit” on page 92 v “2010 LCD front bezel (LCD cover kit)” on page 106 v “2020 LCD rear cover (LCD cover kit)” on page 108 v “2030 Inverter car
Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ThinkLight Integrated camera (for some models) Status indicators Note: For the description of each indicator, see “Status indicators” on page 50.
Rear view 1 2 3 4 5 6 7 8 9 Status indicators Note: For the description of each indicator, see “Status indicators” on page 50.
Parts list This section contains following lists of the service parts. v “Overall” on page 122 v “LCD FRUs” on page 173 v “Keyboard” on page 187 v “Miscellaneous parts” on page 189 v “AC adapters” on page 191 v “Power cords” on page 192 v “Recovery discs” on page 193 v “Common service tools” on page 203 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 27 26 2 25 a b 3 4 d 24 c 23 22 e 5 6 7 21 8 9 10 20 19 11 f 12 13 14 15 18 16 17 122 ThinkPad T500 and W500 Hardware Maintenance Manual
Table 42. Parts list—Overall No. FRU FRU no. RoHS ID CRU ID a - d See “Miscellaneous parts” on page 189. 1 LCD unit (see “LCD FRUs” on page 173.) 2 Keyboard bezel assembly 45N5499 R N 3 SIM card slot 42X3919 R N 4 Speaker assembly 42W3803 R N 4 Speaker assembly 39T7492 R N 5 Modem daughter card (MDC-3.
Table 42. Parts list—Overall (continued) No. 6 124 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 126 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 7 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 128 FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm OP v 2055-CTO, 2Bx, 74x v 2056-CTO, 4Px, 79x v 2081-CTO v 2082-CTO v 2083-CTO, 4Yx v 2087-CTO, 4Zx v 2088-CTO v 2089-CTO, 2Jx, 59x v 2241-CTO, 3Wx, 5Sx, v 2242-CTO v 2243-CTO v 2246-CTO, 4Bx v 2247-CTO, 4Cx v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 42T1491 R * 11 SATA hard disk drive, 80 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm v 2055-CTO, 2Bx, 74x v 2056-CTO, 4Px, 79x v 2081-CTO v 2082-CTO v 2083-CTO, 4Yx v 2087-CTO, 4Zx v 2088-CTO v 2089-CTO, 2Jx, 59x v 2241-CTO, 3Wx, 5Sx, v 2242-CTO v 2243-CTO v 2246-CTO, 4Bx v 2247-CTO, 4Cx v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 42T1575 R * 11 SATA hard disk drive, 160 GB, 9.
Table 42. Parts list—Overall (continued) No. 11 130 FRU FRU no. SATA hard disk drive, 160 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 160 GB, 9.
Table 42. Parts list—Overall (continued) No. 132 FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 250 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 250 GB, 9.
Table 42. Parts list—Overall (continued) No. 134 FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 320 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 320 GB, 9.
Table 42. Parts list—Overall (continued) No. 136 FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 100 GB, 9.5 mm, 7,200 rpm v 2055-CTO, 2Nx v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO, 2Ux v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 39T2799 R * 11 SATA hard disk drive, 160 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 160 GB, 9.
Table 42. Parts list—Overall (continued) No. 138 FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 200 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 250 GB, 9.5 mm, 7,200 rpm v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO, 3Xx, 44x v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 42T1563 R * 11 SATA hard disk drive, 250 GB, 9.
Table 42. Parts list—Overall (continued) No. 140 FRU FRU no. RoHS ID CRU ID 11 SATA hard disk drive, 320 GB, 9.5 mm, 7,200 rpm v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO, 3Vx, 3Wx, 3Yx, 3Zx, 42x, 43x, 45x, 46x, 47x, 48x, 4Ax, 4Bx v 4062-CTO, 3Nx v 4063-CTO, 4Cx v 4064-CTO v 4065-CTO 42T1559 R * 11 SATA hard disk drive, 320 GB, 9.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 12 1.8-inch - 2.
Table 42. Parts list—Overall (continued) No. 142 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 14 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 14 144 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 14 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 146 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 15 RJ11 sub card 42W7887 R N 15 RJ11 sub card 42W7886 R N 16 DVD drive, 9.5 mm v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 42T2511 R N 16 DVD drive, 9.
Table 42. Parts list—Overall (continued) No. 148 FRU FRU no. RoHS ID CRU ID 16 DVD/CD-RW combo drive, 9.
Table 42. Parts list—Overall (continued) No. 16 FRU FRU no. DVD-RAM/RW drive, 9.
Table 42. Parts list—Overall (continued) No. 16 150 FRU FRU no. DVD-RAM/RW drive, 9.
Table 42. Parts list—Overall (continued) No. 16 FRU FRU no. DVD-RAM/RW drive, 9.
Table 42. Parts list—Overall (continued) No. 152 FRU FRU no. RoHS ID CRU ID 16 Blu-ray drive, 9.5 mm v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO, 3Jx, 5Px, 6Rx, 6Zx v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO, 2Fx v 4063-CTO, 2Ux v 4064-CTO v 4065-CTO 42T2517 R * 16 Travel cover, 9.
Table 42. Parts list—Overall (continued) No. 18 18 18 18 18 18 18 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 18 18 18 18 18 18 18 154 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 18 18 18 18 18 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 156 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 158 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 160 FRU FRU no. RoHS ID CRU ID 21 CPU assembly, Intel Core 2 Duo processor P7370 (2.0 GHz) v 2055-CTO, 7Ex, 7Fx v 2056-CTO v 2081-CTO v 2082-CTO, 7Dx v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO, 5Vx v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 42W8149 R N 21 CPU assembly, Intel Core 2 Duo processor P8400 (2.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 21 CPU assembly, Intel Core 2 Duo processor P8600 (2.
Table 42. Parts list—Overall (continued) No. 162 FRU FRU no. RoHS ID CRU ID 21 CPU assembly, Intel Core 2 Duo processor P9500 (2.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 21 CPU assembly, Intel Core 2 Duo processor T5670 (1.
Table 42. Parts list—Overall (continued) No. 164 FRU FRU no. RoHS ID CRU ID 21 CPU assembly, Intel Core 2 Duo processor T6570 (2.1 GHz) v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO 42W8193 R N 21 CPU assembly, Intel Core 2 Duo processor T9400 (2.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 21 CPU assembly, Intel Core 2 Duo processor T9550 (2.
Table 42. Parts list—Overall (continued) No. 21 166 FRU FRU no. RoHS ID CRU ID CPU assembly, Intel Core 2 Duo processor T9800 (2.
Table 42. Parts list—Overall (continued) No. 22 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 168 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 170 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 172 FRU FRU no. RoHS ID CRU ID — Telephone cable, RoHS 91P6915 R * — AC adapter (see “AC adapters” on page 191.
LCD FRUs In ThinkPad T500 and W500, there are following types of LCDs. v “15.4-in. WXGA TFT” on page 174 v “15.4-in. WSXGA+ TFT” on page 181 v “15.4-in.
15.4-in. WXGA TFT Table 43. Parts list—15.4-in. WXGA TFT No. 174 FRU FRU no.
Table 43. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no.
Table 43. Parts list—15.4-in. WXGA TFT (continued) No. 176 FRU FRU no.
Table 43. Parts list—15.4-in. WXGA TFT (continued) No. 8 FRU FRU no. Bluetooth daughter card (BDC-2.
Table 43. Parts list—15.4-in. WXGA TFT (continued) No. 9 178 FRU FRU no. LCD panel, 15.4-in.
Table 43. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no. RoHS CRU ID ID 9 LCD panel, 15.4-in.
Table 43. Parts list—15.4-in. WXGA TFT (continued) No. 180 FRU FRU no. RoHS CRU ID ID 9 LCD panel, 15.4-in.
15.4-in. WSXGA+ TFT Table 44. Parts list—15.4-in. WSXGA+ TFT No. FRU FRU no.
Table 44. Parts list—15.4-in. WSXGA+ TFT (continued) No. 8 182 FRU FRU no. Bluetooth daughter card (BDC-2.
Table 44. Parts list—15.4-in. WSXGA+ TFT (continued) No. 9 FRU FRU no. LCD panel, 15.4-in.
Table 44. Parts list—15.4-in. WSXGA+ TFT (continued) No. 184 FRU FRU no. RoHS ID CRU ID 9 LCD panel, 15.4-in.
15.4-in. WUXGA TFT Table 45. Parts list—15.4-in. WUXGA TFT No. FRU FRU no.
Table 45. Parts list—15.4-in. WUXGA TFT (continued) No. 186 FRU FRU no. RoHS ID CRU ID 8 Bluetooth daughter card (BDC-2.
Keyboard Table 46.
Table 47. Parts list—Keyboard 188 Language P/N Arabic 42T3212 42T3276 42T3146 Belgian 42T3213 42T3277 42T3147 Brazilian Portuguese 42T3240 42T3304 42T3174 Canadian French (058) 42T3211 42T3275 42T3145 Canadian French (Acnor) 42T3210 42T3274 42T3144 Czech 42T3214 42T3278 42T3148 Danish 42T3215 42T3279 42T3149 Dutch 42T3223 42T3287 42T3157 Finnish, Swedish 42T3230 42T3294 42T3164 French 42T3217 42T3281 42T3151 German 42T3218 42T3282 42T3152 Greek (U.S.
Miscellaneous parts Table 48. Parts list—Miscellaneous parts FRU P/N RoHS ID CRU ID Screw kit (including nylon-coated screws): v M2 × 5 mm (black), flat head (11) v M2 × 2.7 mm (black), flat head (10) v M2 × 3.5 mm (black), bind head (18) v M2 × 14 mm (black), flat head (10) v M2 × 14 mm with TB2440B (2) v M2 × 2.8 mm (silver), flat head (5) v M2 × 14 mm HDD security (2) v Security screw (2) v M2.5 × 4 mm (black), flat head (2) v M2.5 × 6.
Table 48. Parts list—Miscellaneous parts (continued) FRU P/N RoHS ID CRU ID System miscellaneous parts: v (a)Cable assembly, DC in. v (b) Bracket, N/B, fan discrete/integ. v (c) Bracket, VGA, fan discrete/integ.
AC adapters Table 49.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 51. Parts list—2-pin power cords Region P/N Argentina v models -CTO, xxY 42T5020 42T5105 Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -Exx, Jxx 42T5014 42T5099 RoHS ID CRU ID R * RoHS ID CRU ID R * Table 52.
Recovery discs Windows XP Professional DVDs Windows XP Professional is preinstalled as the operating system in the following models: v 2055-CTO, 62x, 63x, 64x, 65x v 2056-CTO, 63x v 2081-CTO v 2082-CTO, 27x, 3Hx, 5Ax, 5Bx, 5Xx, 5Yx, 5Zx, 6Mx, 6Nx, 6Yx, 7Px, 7Qx, 7Tx, 7Ux v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO, 53x, 58x, 59x, 5Ax v 2241-CTO, 58x v 2242-CTO, 23x, 33x, 35x, 3Ax, 4Fx, 55x, 5Fx, 5Gx, 5Hx, 6Cx v 2243-CTO, 3Cx, 4Lx, 4Mx, 56x, 57x, 5Lx, 64x, 65x, 68x, 69x v 2246-CTO v 2247-CTO v 2261-CTO v 405
Table 53.
Windows Vista Home Basic (32 bit) DVDs Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO, 28x, v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO, 2Hx v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO ThinkPad T500 and W500 195
Table 54.
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2055-CTO v 2056-CTO v 2081-CTO, 52x v 2082-CTO, 7Dx v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO, 27x, 38x, 39x, 4Gx, 4Hx, 4Jx, 5Vx, 66x v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO, 2Gx v 4058-CTO v 4061-CTO v 4062-CTO v 4063-CTO v 4064-CTO v 4065-CTO Table 55.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 2055-CTO, 2Bx, 2Cx, 2Dx, 2Ex, 2Lx, 2Mx, 2Nx, 2Px, 2Vx, 2Xx, 3Ax, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Ex, 4Fx, 4Gx, 4Hx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx, 74x, 75x, 76x, 77x, 78x, 7Ex, 7Fx, 7Hx, 7Jx, 7Kx, 7Lx, E1x, E2x v 2056-CTO, 34x, 4Kx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 5Tx, 79x, 7Ax, 7Bx, 7Cx, 7Lx, E1x, E2x v 2081-CTO, 22x, 24x v 2082-CTO, 26x, 28x, 3Fx, 3Gx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Rx
Table 56.
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 2055-CTO v 2056-CTO v 2081-CTO v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO v 4061-CTO, 32x, 3Vx, 42x, 46x, 4Bx v 4062-CTO, 25x, 2Fx v 4063-CTO, 34x v 4064-CTO v 4065-CTO Table 57.
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 2055-CTO v 2056-CTO v 2081-CTO, 3Ex, 53x v 2082-CTO v 2083-CTO v 2087-CTO v 2088-CTO v 2089-CTO v 2241-CTO v 2242-CTO, 24x, 5Ex v 2243-CTO v 2246-CTO v 2247-CTO v 2261-CTO v 4058-CTO, 3Lx v 4061-CTO, 2Mx, 2Nx, 2Px, 2Qx, 4Ax v 4062-CTO, 28x, 2Ax, 2Xx, 3Cx, 3Gx, 3Hx v 4063-CTO, 2Tx, 2Ux v 4064-CTO v 4065-CTO ThinkPad T500 and W500 201
Table 58.
Common service tools Table 59. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
204 ThinkPad T500 and W500 Hardware Maintenance Manual
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 43Y6630_03 (1P) P/N: 43Y6630_03
